Ozito PXMFTS-100U Bruksanvisning

Ozito Multiverktyg PXMFTS-100U

Läs nedan 📖 manual på svenska för Ozito PXMFTS-100U (4 sidor) i kategorin Multiverktyg. Denna guide var användbar för 7 personer och betygsatt med 4.5 stjärnor i genomsnitt av 2 användare

Ladda ner PDF

Sida 1/4

Category Example

Wear parts* Carbon brushes, Triangular sanding/grinding plate,

Scraper, HSS saw blade, Diamond Saw blade, Battery

Consumables* Grinding/sanding paper

Missing parts

SPECIFICATIONS

Voltage: 18V

No Load Speed: 11,000-20,000/min

Orbit Angle: 3.2°

Sanding Pad Size: 90 x 90 x 90mm

Sandpaper Size: 93 x 93 x 93mm

Weight: 1kg

MULTI FUNCTION

TOOL

ORIGINAL INSTRUCTIONS

STANDARD EQUIPMENT

Multi Function Tool

TROUBLESHOOTING

• Keep ventilation slots of the multi function tool clean at all times to ensure efﬁ cient

operation.

• After each use, blow air through the tool housing to ensure it is free from all dust,

dirt, etc. Build up of dust, dirt particles may cause the tool to overheat and shorten

the life of the tool.

• If the housing of the multi function tool requires cleaning, do not use solvents but a

moist soft cloth or soft brush only.

• Never let any liquid get inside the tool, never immerse any part of the tool into liquid.

• No lubrication is necessary as the tool has sealed bearings.

• When not in use, the multi function tool should be stored in a dry, frost free location

not within the reach of children.

WARNING! ALWAYS ENSURE THE TOOL HAS

COMPLETELY STOPPED AND THE BATTERY IS

REMOVED PRIOR TO ANY MAINTENANCE.

Battery protection system

The tool is equipped with the battery protection system, which helps to ensure a long service

life.

The output power automatically cuts off during operation when the tool and/or battery are

placed under the following situations:

• When the tool is overloaded:

If this occurs, release the trigger switch and remove causes of overload, then pull the

switch trigger again to restart.

• When the remaining battery capacity becomes low:

Recharge the battery pack.

Note: The battery protection system does not in any way damage the tool.

Note: The indicated capacity may be lower than the actual level during use or immediately

after using the tool.

LED lights do not illuminate on charger

Check the charging adaptor is securely plugged into the wall out let.

Check the battery is ﬁ rmly connected to the charging cradle.

Check that the charging jack is securely connected to the charging cradle.

Sparking visible through the housing air vents

A small amount of sparking may be visible through the housing vents. This is normal

and does not indicate a problem.

Accessories are falling off the spindle after locking

For non-Ozito multi function tool compatible accessories, the included accessory

adapter may need to be ﬁ tted to ensure the accessory is secured correctly.

Note: Ozito Industries will not be responsible for any damage or injuries

caused by the repair of the multi function tool by an unauthorised person or by

mishandling of the multi function tool.

MULTI FUNCTION TOOL SAFETY WARNINGS

Accessories

MAINTENANCE

PXMFTS-100U

Art.-No.: 30.002.86 I.-No.: 11017

0318

WOOD M ETA L

WARNING!

• This tool may only be used for dry grinding/sanding operations.

• Use of the tool on materials containing asbestos is prohibited.

• Keep your workplace clean and well illuminated.

• Make sure that the workpiece is sufficiently secured so that it cannot slip.

• Keep children away.

• For your own sake, keep the machine clean at all times and check it for signs of

damage each time after using it.

• Make sure that the switch is set to OFF before you insert the plug into the power

supply socket.

• Make sure of your footing, particularly when working on ladders and platforms.

• Harmful or toxic dust can be produced when working on wood or metal.

Touching or inhaling this dust can be harmful for the operator and other persons

nearby.

• To protect your health, always wear safety goggles and a dust mask during san-

ding/grinding work!

• If you discover any damage to the machine, use the exploded diagram and the

spare parts list to determine which parts need to be ordered from Customer

Service.

• Important! Wear safety goggles and a dust mask.

Do not lose these safety instructions.

ozito-diy.co.uk

WARRANTY

iSC GmbH · Eschenstraße 6 · 94405 Landau /Isar · Germany

All of our products undergo strict quality checks to ensure that they reach you in perfect

condition. In the unlikely event that your device develops a fault, please contact our service

department at the address shown on this guarantee card. You can also contact us by

telephone using the customer service number shown. Please note the following terms under

which guarantee claims can be made:

1. These warranty terms regulate additional warranty services, which the manufacturer

mentioned below promises to buyers of its new products in addition to their statutory

guarantee claims are not affected by this guarantee. Our guarantee is free of charge to you.

2. The warranty services only covers defects due to material or manufacturing faults on

a product which you have bought from the manufacturer mentioned below are limited to

either the rectiﬁ cation of said defects on the product or the replacement of the product,

whichever we prefer.

Please note that our devices are not designed for use in commercial, trade or professional

applications. A guarantee contract will not be created if the device has been used by

commercial, trade or industrial business or has been exposed to similar stresses during the

guarantee period.

3. The following are not covered by our guarantee:

- Damage to the device caused by a failure to follow the assembly instructions or due to

incorrect installation, a failure to follow the operating instructions (for example connecting

it to an incorrect mains voltage or current type) or a failure to follow the maintenance and

safety instructions or by exposing the device to abnormal environmental conditions or by

lack of care and maintenance.

- Damage to the device caused by abuse or incorrect use (for example overloading the

device or the use or unapproved tools or accessories), ingress of foreign bodies into the

device (such as sand, stones or dust, transport damage), the use of force or damage caused

by external forces (for example by dropping it).

- Damage to the device or parts of the device caused by normal or natural wear or tear or by

normal use of the device.

4. Your Product is guaranteed for a period of 60 months from the original date of purchase

and is intended for DIY (Do It Yourself) use only. Lithium Ion batteries and chargers are

covered by a 12 month warranty. Warranty excludes consumable parts. Guarantee claims

should be submitted before the end of the guarantee period within two weeks of the defect

being noticed. No guarantee claims will be accepted after the end of the guarantee period.

The original guarantee period remains applicable to the device even if repairs are carried

out or parts are replaced. In such cases, the work performed or parts ﬁ tted will not result

in an extension of the guarantee period, and no new guarantee will become active for the

work performed or parts ﬁ tted. This also applies if an on-site service is used.

IN ORDER TO MAKE A CLAIM UNDER THIS WARRANTY YOU MUST RETURN THE PRODUCT TO

THE PLACE OF PURCHASE WITH YOUR REGISTER RECEIPT.

Please refer to the restrictions of this warranty concerning wearing parts, consumables and

missing parts as set out in the service information in these operating instructions.

CUSTOMER SERVICE HELPLINE

GB: 0151 294 4488

IRL: 1850 882711

Ozito-diy.co.uk

SOUND & VIBRATION

Sound and vibration values were measured in accordance with EN 60745.

Lpa sound pressure level: 78 dB

Kpa uncertainty: 3 dB

Lwa

sound power level: 89 dB

Kwa uncertainty: 3 dB

Wear ear-muffs.

The impact of noise can cause damage to hearing.

Total vibration values (vector sum of three directions) determined in accordance with EN 60745.

Handle

Vibration emission value ah = 13.9 m/s2

K uncertainty = 1.5 m/s2

Keep the noise emissions and vibrations to a minimum.

• Only use appliances which are in perfect working order.

• Service and clean the appliance regularly.

• Adapt your working style to suit the appliance.

• Do not overload the appliance.

• Have the appliance serviced whenever necessary.

• Switch the appliance off when it is not in use.

• Wear protective gloves.

SERVICE INFORMATION

Please note that the following parts of this product are subject to normal or natural

wear and that the following parts are therefore also required for use as consumables.

* Not necessarily included in the scope of delivery!

DESCRIPTION OF SYMBOLS

Danger! Read the operating instructions to reduce the risk of inquiry.

Caution! Wear ear-muffs. The impact of noise can cause

damage to hearing.

Caution! Wear a breathing mask. Dust which is injurious to

health can be generated when working on wood and other materials. Never

use the device to work on any materials containing asbestos!

Caution! Wear safety goggles. Sparks generated during

working or splinters, chips and dust emitted by the device can cause

loss of sight.

SPARE PARTS

Dust extraction adapter (Art. No.: 44.651.63)

Spare parts can be ordered from the Special Orders Desk at your local

Bunnings Warehouse or Homebase store.

For further information, or any parts visit

www.ozito-diy.co.uk or contact Ozito Customer Service:

Great Britain: 0151 294 4488

Ireland: 1850 882711

E-mail: info@ozito-diy.co.uk

For EU countries only

Never place any electric power tools in your household refuse.

To comply with European Directive 2012/19/EC concerning old electric and electronic equipment and its

implementation in national laws, old electric power tools have to be separated from other waste and

disposed of in an environment-friendly fashion, e.g. by taking to a recycling depot.

Recycling alternative to the return request:

As an alternative to returning the equipment to the manufacturer, the owner of the electrical

equipment must make sure that the equipment is properly disposed of if p1-he no longer wants to keep

the equipment. The old equipment can be returned to a suitable collection point that will dispose of

the equipment in accordance with the national recycling and waste disposal regulations. This does not

apply to any accessories or aids without electrical components supplied with the old equipment.

The reprinting or reproduction by any other means, in whole or in part, of documentation and papers

accompanying products is permitted only with the express consent of the iSC GmbH.

Subject to technical changes

DECLARATION OF CONFORMITY

Nigel Yang/Product-ManagementAndreas Weichselgartner/General-Manager

explains the following conformity according to EU directives and norms for

the following product

Cordless Multifunction Tool PXMFTS-100U (Ozito)

2014/29/EU

2005/32/EC_2009/125/EC

(EU)2015/1188

2014/35/EU

2006/28/EC

X2014/30/EU

2014/32/EU

2014/53/EU

2014/68/EU

(EU)2016/426

Notiﬁ ed Body:

(EU)2016/425

X2011/65/EU_(EU)2015/863

X2006/42/EC

Annex IV

Notiﬁ ed Body:

Reg. No.:

2000/14/EC_2005/88/EC

Annex V

Annex VI

Noise: measured LWA

= dB (A); guaranteed LWA = dB (A)

P = KW; L/Ø = cm

Notiﬁ ed Body:

2012/46/EU_(EU)2016/1628

Emission No.:

Standard references: EN 62841-1; EN 62841-2-4;

EN 55014-1; EN 55014-2; EN 62321

Landau/Isar, den 11.12.2019

First CE: 17 Archive-File/Record: NAPR018291

Art.-No.: 30.002.86 I.-No.: 11017 Documents registrar: Georg Riedel

Subject to change without notice Wiesenweg 22, D-94405 Landau/Isar

ISC GmbH · Eschenstraße 6 · D-94405 Landau/Isar

GENERAL POWER TOOL SAFETY WARNINGS

ELECTRICAL SAFETY

WARNING! When using mains-powered tools, basic safety precautions, including the

following, should always be followed to reduce risk of ﬁ re, electric shock, personal injury

and material damage.

Read the whole manual carefully and make sure you know how to switch the tool off in an emergency, before operating the tool.

Save these instructions and other documents supplied with this tool for future reference.

Before you connect the charger to the mains supply make sure that the data on the rating plate are identical to the mains data.

This tools charger is double insulated; therefore no earth wire is required.

If the supply cord is damaged, it must be replaced by an electrician or a power tool repairer in order to avoid a hazard.

Note: Double insulation does not take the place of normal safety precautions when operating this tool. The insulation system is for

added protection against injury resulting from a possible electrical insulation failure within the tool.

The power supply for this products charger should be protected by a residual current device (rated at 30mA or less). A residual current

device reduces the risk of electric shock.

WARNING! Read all the safety information, instructions, illustrations and technical data

provided on or with this power tool. Failure to adhere to the following instructions may result

in electric shock, ﬁ re and/or serious injury.

Keep all the safety information and instructions in a safe place for future use.

The term „power tool“ used in the safety information and instructions refers to power tools operated

from the mains power supply (with a power cable) and to battery operated power tools (without a power

cable).

1. Workplace safety

a) Untidy or unlit work areas can result in acci-Keep your work area clean and well illuminated.

dents.

b) Do not operate the electric tool in an environment where there is a risk of explosions and

where there are inﬂ ammable liquids, gases or dust. Electric tools produce sparks which could

set the dust or vapours alight.

c) If you are Keep children and other people away from the power tool while you are using it.

distracted you may lose control of the power tool.

2. Electrical safety

a) The connector plug from this electric tool must ﬁ t into the socket. The plug should never

be altered in any way. Never use adapter plugs together with earthed electric tools. Unalte-

red plugs and correct sockets reduce the risk of an electric shock.

b) Avoid bodily contact with earthed surfaces such as pipes, heating, ovens and fridges. The

risk of electric shock is increased if your body is earthed.

c) The ingress of water into an electric tool Keep the tool out of the rain and away from moisture.

increases the risk of an electric shock.

d) Do not use the power cable for a purpose for which it is not designed, for example to carry

the power tool, hang it up or to pull the plug out of the socket. Keep the power cable away

from heat, oil, sharp edges and moving parts. Power cables that are damaged or tangled in-

crease the risk of an electric shock.

e) If you use an electric power tool outdoors, use only extension cables that are suitable for

outdoor use. The use of an extension cable which is suitable for outdoor use reduces the risk of

an electric shock.

f) If operation of the electric tool in a damp environment can not be avoided, use a earth-lea-

kage circuit-breaker. The earth-leakage circuit-breaker reduces the risk of an electric shock.

3. Safety of persons

a) Be careful, watch what you are doing and use an electric tool sensibly. Do not use the tool

if you are tired or under the inﬂ uence of drugs, alcohol or medication. A moment of inattenti-

on when using the electric tool can result in serious injuries.

b) Wearing personal Wear personal protection equipment and always wear safety goggles.

protection (such as dust masks, non-slip safety shoes, safety helmet or ear protection, depending

upon the type and use of the electric tool) reduces the risk of injury.

c) Make sure that the appliance cannot start up accidentally. Ensure that the electric tool is

switched oﬀ before you connect it to the power supply and/or insert the battery, or pick up

or carry the tool. If your ﬁ nger is on the switch whilst carrying the electric tool or if you connect

the appliance to the mains when it is switched on, this can lead to accidents.

d) Any tool or Remove all adjusting tools or wrenches before you switch on the power tool.

wrench in a rotating part of the power tool could cause injuries.

e) Avoid abnormal working postures. Make sure you stand squarely and keep your balance at

all times. This will enable you to control the power tool better in unexpected situations.

f) Wear suitable clothes. Never wear loose ﬁ tting clothes or jewelry. Keep hair, clothing and

gloves away from moving parts. Loose clothing, jewelry or long hair can be caught by moving

parts.

g) If dust extraction devices and dust collection devices can be ﬁ tted, they must be connected

and must be used correctly. The use of a dust extractor can reduce the dangers posed by dust.

h) Do not allow yourself to be lulled into a false sense of security and do not ignore the safety

regulations covering electric power tools, even if you are familiar with the power tool after

having used it many times. Carelessness can lead to serious injuries in just a fraction of a se-

cond.

4. Using and handling the power tool

a) The cor-Do not overload your power tool. Use the correct electric tool for the job in hand.

rect tool will enable you to work better and more safely within the speciﬁ c performance range.

b) An electric power tool that cannot Do not use an electric power tool if the switch is defective.

be switched on or oﬀ is dangerous and must be repaired.

c) Pull the plug out of the socket and/or remove the battery pack before making any adjust-

ments to the tool, changing accessories or putting the power tool down. These precautions

will prevent the power tool starting accidentally.

d) Keep unused electric tools out of the reach of children. Do not allow people who are not

familiar with the power tool or who have not read these instructions to use the tool. Electric

tools are dangerous if they are used by inexperienced people.

e) Look after power tools plug-in tools with care. Check that moving parts function correctly

and do not jam, and whether any parts are broken or damaged such that they adversely af-

fect the function of the power tool. Have damaged parts repaired before you use the power

tool. Many accidents are caused by poorly maintained electric tools.

f) Carefully maintained cutting tools with sharp cutting edges Keep cutting tools sharp and clean.

will jam less and are easier to control.

g) Use the power tool, accessories, plug-in tools, etc. as set out in these instructions. Take

account of the conditions in your work area and the job in hand. Using electric tools for pur-

poses other than the one for which they are designed can result in dangerous situations.

h) Keep the handles and grip surfaces dry, clean and free from oil and grease. If the handles

and grip surfaces are slippery, it will not be possible to operate and control the power tool safely in

unforeseen situations.

5. Using and handling the cordless tool

a) Only charge the batteries in chargers that are recommended by the manufacturer. A charger

that is designed for a certain type of battery may pose a ﬁ re risk if it is used with other types of

battery.

b) The use of other batteries may result in Use only the correct batteries in the electric tools.

injuries and a ﬁ re risk.

c) Keep unused batteries away from paper clips, coins, keys, nails, screws and other metallic

objects that could cause a short circuit between the contacts. A short circuit between the bat-

tery contacts may cause burns or a ﬁ re.

d) In case of incorrect use, ﬂ uid may escape from the battery. Avoid contact with it. If you

touch it by accident, rinse the aﬀ ected area with water. If you get the ﬂ uid in your eyes, also

seek medical advice. Leaking battery ﬂ uid can cause skin irritation or burns.

e) Damaged or altered rechargeable bat-Never use damaged or altered rechargeable batteries.

teries can behave unpredictably and lead to a risk of ﬁ re, explosion or injury.

f) Never expose a rechargeable battery to ﬁ re or high temperatures. Fire or temperatures over

130°C pose a risk of explosion.

g) Follow all the instructions on charging and never charge the rechargeable battery or cord-

less tool outside the speciﬁ ed allowable charging temperature range. Incorrect charging or

charging outside the allowable charging temperature range could cause irreparable damage to the

battery and increase the risk of ﬁ re.

6. Service

a) Have your electric tool repaired only by trained personnel using only genuine spare parts.

This will ensure that your electric tool remains safe to use.

b) Never perform maintenance work on damaged rechargeable batteries. All maintenance work

on rechargeable batteries should only be performed by the manufacturer or authorized after sales

service outlets..

Anleitung_PXMFTS_100U.indd 1-4

Anleitung_PXMFTS_100U.indd 1-4Anleitung_PXMFTS_100U.indd 1-4 28.01.2020 16:01:59

28.01.2020 16:01:59

28.01.2020 16:01:5928.01.2020 16:01:59

2. FITTING THE BATTERY

WOOD METAL

PXMFTS-100U

5. SANDING4. CONTROLS3. FITTING ACCESSORIES

KNOW YOUR PRODUCT

1. BEFORE USE

SETUP & PREPARATION

WARNING! ENSURE THE TOOL IS SWITCHED OFF AND

THE BATTERY IS REMOVED BEFORE PERFORMING ANY

OF THE FOLLOWING TASKS.

WARNING! AFTER USE, HOLD THE TOOL AWAY FROM

YOUR BODY UNTIL THE SPINDLE STOPS COMPLETELY.

6. SAWING AND SCRAPPING

OPERATION

CORDLESS MULTI FUNCTION TOOL

ACCESSORIES

1 2 3 4

7 8 9 10 11 12 13

1 Accessory Locking Lever

2 On/Off Switch

3 Variable Speed Dial

4 Battery Seating

5 Accessory Drive Spindle

6 Sure Grip Handle

7 Sanding Pad

8 Sanding Paper

(3 x 60grit, 3 x 80grit, 3 x 120grit)

9 Wood Plunge Blade

10 Metal Plunge Blade

11 Semi-Circular Blade

12 Scraper

13 Accessory Adapter

Inserting & Removing the Battery

1 Slide the battery into the seating at the back of the tool until it clicks into

place.

2 To remove, press and hold the battery release tab and then slide out.

Turning On and Off

Fitting Sand Paper

Sawing or Cutting

Scraping

Sanding

Variable Speed Control

1 To start the tool press the on/

off switch forward into the on

position.

1 To increase the speed of the tool,

rotate the variable speed dial to

a higher number.

2 To decrease the speed of the

tool, rotate the variable speed

dial to a lower number.

2 To stop the tool press the on/

off switch backward into the off

position.

Note: Do not apply heavy pressure to the tool or tilt the sanding base as this

will wear out the sanding paper and may damage the sanding pad.

Note: Ensure blades are not blunt or damaged in any way before

commencing.

Note: Allow the scraper to do the work; do not apply heavy pressure to the

tool. This may cause the multi function tool to overload or cut into the surface

of the material.

ONLINE MANUAL

Scan this QR Code with your

mobile device to take you to the

online manual.

BATTERY & CHARGER

This tool is compatible with all batteries and chargers from the Ozito

Power X Change Range.

WARNING! KEEP FINGERS CLEAR OF SPINDLE WHEN

SECURING THE ACCESSORY TO AVOID PINCHING.

Attaching Accessories

Removing Accessories

2 Place the desired accessory

onto the accessory drive

spindle ensuring the holes in

the accessory align with the

notches on the tool.

4 Rotate the

accessory locking

lever clockwise

to secure the

accessory.

Note: Pull on the

accessory to check if it

is secured correctly.

1 To remove the accessory rotate the

locking lever anti-clockwise and

then remove from the spindle.

1 Rotate the accessory locking

lever anti-clockwise to open

spindle ﬁtment.

3 When using other non-Ozito

multi function tool compatible

accessories, the accessory

adapter may need to be ﬁtted to

secure correctly.

10° - 15°

2 Press the sanding

paper onto the

sanding pad by

aligning the edges

and holes.

2 Switch the tool

on use a slight

pendulum motion

while cutting.

2 Hold the tool at an

angle of 10°-15° to

the workpiece.

2 Place the multi

function tool ﬂat

on the workpiece

and make smooth

back and forth

movements.

1 The sanding pad must ﬁrst be

ﬁtted to the spindle following

the instructions in the previous

section. 1 Ensure the work piece is securely

held down and the accessory is

secure.

1 Ensure the accessory is secure,

and then start the tool.

1 Ensure the accessory is secure,

and then start the tool.

3 To remove, peel away from the

sanding pad starting from an

edge.

With the sanding pad and sand paper ﬁtted, the multi function tool can be

used on materials such as wood, plastic and painted surfaces. When sawing, the multi function tool can be used on wood, plastic and sheet

metal using the correct accessory.

When being used as a scraper, the tool can remove materials such as fabric,

adhesives, vinyl or paint from wood, plastic and metal.

Items Supplied

Please check that the article is complete as speciﬁed in the scope of delivery. If parts

are missing, please contact our service center or the sales outlet where you made

your purchase at the latest within 5 working days after purchasing the product and

upon presentation of a valid bill of purchase. Also, refer to the warranty table in the

service information at the end of the operating instructions.

• Open the packaging and take out the equipment with care.

• Remove the packaging material and any packaging and/or transportation braces

(if available).

• Check to see if all items are supplied.

• Inspect the equipment and accessories for transport damage.

• If possible, please keep the packaging until the end of the guarantee period.

Danger!

The equipment and packaging material are not toys. Do not

let children play with plastic bags, foils or small parts. There

is a danger of swallowing or suffocating!

Proper Use

The equipment is suitable for sanding/grinding small areas. For larger areas we

recommend the use of a dust extraction adaptor, which is available for purchase (see

‘Spare Parts’ section of this manual).

The equipment is designed for the sanding/grinding of wood, iron, plastic and

similar materials using the appropriate abrasive paper. Furthermore, the equipment

is intended for sawing wood, plastic and similar materials, as well as scraping off

glued carpets, ﬁlling compound residues, old paint and similar applications.

The equipment is to be used only for its prescribed purpose. Any other use is deemed

to be a case of misuse. The user / operator and not the manufacturer will be liable

for any damage or injuries of any kind caused as a result of this.

Please note that our equipment has not been designed for use in commercial, trade

or industrial applications. Our warranty will be voided if the machine is used in

commercial, trade or industrial businesses or for equivalent purposes.

Caution!

Residual risks

Even if you use this electric power tool in accordance with

instructions, certain residual risks cannot be rules out.

The following hazards may arise in connection with the

equipment’s construction and layout:

1. Lung damage if no suitable protective dust mask is used.

2. Damage to hearing if no suitable ear protection is used.

3. Health damage caused by hand-arm vibrations if the equipment is used over a

prolonged period or is not properly guided and maintained.

To absorb the vibrations which arise

on the rechargeable battery, there

is some play between the battery

and the tool’s battery seating. This

is normal and has no effect on the

performance of the equipment or the

rechargeable battery

Vibration Absorption

Anleitung_PXMFTS_100U.indd 5-8

Anleitung_PXMFTS_100U.indd 5-8Anleitung_PXMFTS_100U.indd 5-8 28.01.2020 16:02:00

28.01.2020 16:02:00

28.01.2020 16:02:0028.01.2020 16:02:00

Produktspecifikationer

Varumärke:	Ozito
Kategori:	Multiverktyg
Modell:	PXMFTS-100U
Färg på produkten:	Green, Orange
Vikt:	8900 g
Bredd:	1250 mm
Djup:	660 mm
Höjd:	740 mm
Maximal viktbelastning:	- kg
Kijkglas:	Ja
Antalet hjul:	2 wiel(en)
Förvaringsväska:	Ja
Hopfällbar:	Ja
Bredd hopfälld:	740 mm
Djup när den är hopfälld:	200 mm
Färgning:	Afbeelding
Hjulhjul:	Ja
Antal ben/ben:	4 poot/poten
Lätt att vika ihop:	Ja
Lätt att montera:	Ja
Utfartsplats:	Zijkant