Panduit MSPT-1.3 Bruksanvisning

Läs nedan 📖 manual på svenska för Panduit MSPT-1.3 (6 sidor) i kategorin Inte kategoriserad. Denna guide var användbar för 7 personer och betygsatt med 4.5 stjärnor i genomsnitt av 2 användare

Sida 1/6
MSPT-1.3
PA26214A01
Rev. 01 18-Sep-09
© Panduit Corp. 2009
TOOL SPECIFICATIONS .......................................................................................... 1
Safety ........................................................................................................................ 1
PRECAUTIONS AND GENERAL GUIDELINES ...................................................... 2
TOOL OPERATION .................................................................................................. 3
Bushings .................................................................................................................... 3
MAINTENANCE ........................................................................................................ 3
SPARE PARTS LISTING .......................................................................................... 5
Website: www.panduit.com
Email: cs@panduit.com
Panduit Corp. • USA Headquarters • Tinley Park, IL
Tel: 888-506-5400, ext. 3255 • Fax: 630-759-7532
MSPT-1.3
MSPT-1.3: PA26214A01_01 Page: 1 of 5 18-Sep-09
The Panduit MSPT-1.3 Stud Punch tool punches a 34.1 mm (1-11/32") round hole
in 25 GA. min. to 20 GA max. mild steel studs.
TOOL SPECIFICATIONS
7.0 lbs. (3.2 kg)
NOTE: In the interest of higher quality and value, Panduit products are continually being
improved and updated. Consequently, pictures may vary from the enclosed product.
Safety
Safety
Safety
SafetySafety
Safety is essential in the use and maintenance of Panduit tools and equipment. This manual and any
markings on the tool provide information for avoiding hazards and unsafe practices related to the use of
this tool. Observe all of the safety information provided.
MSPT-1.3
MSPT-1.3: PA26214A01_01 Page: 2 of 5 18-Sep-09
PRECAUTIONS AND GENERAL GUIDELINES
This symbol is used to call your attention to hazards or unsafe practices which could result in an
injury or property damage. The signal word, defined below, indicates the severity of the hazard.
The message after the signal word provides information for preventing or avoiding the hazard.
WARNING Hazards which, if not avoided, COULD result in severe injury or death.
CAUTION Hazards or unsafe practices which, if not avoided, MAY result in injury or
property damage.
WARNING
Read and understand all of the instructions and safety information in this manual
before operating or servicing this tool.
WARNING
Wear eye protection when operating or servicing this tool.
Failure to wear eye protection can result in serious eye injury from flying debris.
WARNING
Electric Shock Hazard:
This tool is not insulated. When using this unit on or near energized electrical lines,
use proper personal protective equipment.
CAUTION
Inspect the tool prior to use. Replace worn, damaged or missing components with replacement parts.
A damaged or improperly assembled tool may break. Use this tool for manufacturer’s intended use
only. Use other than that which is described in this manual may result in injury or damage to the tool.
CAUTION
Do not add extensions (cheaters) to the handles. Using excessive force may result in injury or
damage to the tool. If excessive force is required to complete a punch, verify that the type and
thickness of material do not exceed the capacity of the tool.
IMPORTANT INFORMATION
Do not use on heavier than 20 gauge mild steel.

Produktspecifikationer

Varumärke: Panduit
Kategori: Inte kategoriserad
Modell: MSPT-1.3

Behöver du hjälp?

Om du behöver hjälp med Panduit MSPT-1.3 ställ en fråga nedan och andra användare kommer att svara dig




Inte kategoriserad Panduit Manualer

Inte kategoriserad Manualer

Nyaste Inte kategoriserad Manualer