Planet MFB-TFA40 Bruksanvisning

Läs nedan 📖 manual på svenska för Planet MFB-TFA40 (4 sidor) i kategorin Inte kategoriserad. Denna guide var användbar för 6 personer och betygsatt med 4.5 stjärnor i genomsnitt av 2 användare

Sida 1/4
- 1 -
- 2 -
- 3 -
- 4 -
- 5 -
- 6 -
- 7 -
- 8 -
1. Overview
Thank you for purchasing PLANET MFB family SFP
100Base-FX Fast Ethernet module. The MFB family SFP
Fast Ethernet module can install into PLANET Switch
products with 100Base-FX SFP interface. The distance
can be extended from 2km (MM) up to 60 kilometers
(Single-mode, LC).
2. Model List
Your MFB family SFP Fast Ethernet module comes with
one of the following models.
Fast Ethernet SFP module List
Model Interface Fiber connector and distance
MFB-FX
SFP-Port
100Base-FX
Module
LC, Multi-Mode (1310nm)
-2km
MFB-F20
SFP-Port
100Base-FX
Module
LC, Single Mode (1310nm)
20km
MFB-F40
SFP-Port
100Base-FX
Module
LC, Single Mode (1310nm)
40km
MFB-F60
SFP-Port
100Base-FX
Module
LC, Single Mode (1310nm)
60km
MFB-FA20
SFP-Port
100Base-BX
Module
LC WDM, Single Mode
(TX:1310nm, RX:1550nm)
-20km
MFB-FB20
SFP-Port
100Base-BX
Module
LC WDM, Single Mode
(TX:1550nm, RX:1310nm)
-20km
* Models with last two numbered characters indicate the
maximum distance in km.
3. Check List
Your MFB carton should contain the following items:
The MFB family SFP Fast Ethernet module
This user’s manual
If any item is missing or damaged, please consult the
dealer from whom you purchased you MFB family SFP
Fast Ethernet module.
l
l
4. Introduction
4-1 1-Port 100Base-FX SFP Modules MFB-
FX / MFB-F20 / MFB-F40 / MFB-F60
Features:
Comply with IEEE 802.3u Fast Ethernet standard
1 x 100Mbps ber port
Plug and Play Installation
MFB-FX provides distance up to 2km over 62.5/125μm
multi-mode ber cable
MFB-F20 provides distance up to 20km over 9/125μm
single mode ber cable
MFB-F40 provides distance up to 40km over 9/125μm
single mode ber cable
MFB-F60 provides distance up to 60km over 9/125μm
single mode ber cable
l
l
l
l
l
l
l
4-2 1-Port 100Base-BX WDM SFP Modules
MFB-FA20 / MFB-FB20
Features:
Comply with IEEE 802.3u Fast Ethernet standard
1 x 100Mbps ber port (Single LC ber connectors)
Plug and Play Installation
MFB-FA20 provides distance up to 20km over
9/125μm single mode ber cable
MFB-FB20 provides distance up to 20km over
9/125μm single mode ber cable
Caution
The MFB series single mode SFP trans-
ceivers provide the optical power budget
from 15 dB to 30dB. When shorter
distance of single-mode fiber cables is
used, you might need to insert an in-
line optical attenuator in the link to avoid
overloading the receiver:
l
l
l
l
l
SFP Model
In-line
Optical
Attenuator
MFB-F20 MFB-F40 MFB-F60 MFB-FA20 MFB-FB20
Optical power
budget 15 dB 24 dB 30 dB 20 dB 20 dB
Fiber Cable Length
= 10 Km 5 dB 10 dB 15 dB 5 dB 5 dB
15Km Fiber
Cable Length <
60Km
2 dB 10 dB -- 2 dB 2 dB
5. Installing SFP Modules
5.1 Installing the SFP transceiver
The sections describe how to insert an SFP transceiver
into an SFP slot.
The SFP transceivers are hot-pluggable and hot-
swappable. You can plug-in and out the transceiver to/
from any SFP port without having to power down the
Switch/Media Converter. As the Figure -1 appears.
MFB MFB
Figure 1 Plug-in the SFP transceiver
Before connect the other switches, workstation or Media
Converter.
1. Make sure both side of the SFP transceiver are with
the same media type or WDM pair, for example:
100Base-FX to 100Base-FX, 100Base-BX20-U to
100Base-BX20-D.
2. Check the ber-optic cable type match the SFP trans-
ceiver model.
To connect to MFB-FX SFP transceiver, use the
multi-mode ber cable- with one side must be male
duplex LC connector type.
To connect to MFB-F20/F40/F60/FA20/FB20 SFP
transceiver, use the single-mode ber cable-with
one side must be male duplex LC connector type.
Connect the ber cable
1. Attach the duplex LC connector on the network cable
into the SFP transceiver.
2. Connect the other end of the cable to a device
switches with SFP installed, ber NIC on a worksta-
tion or a Media Converter.
3. Check the LNK/ACT LED of the SFP slot of the switch
/ converter. Ensure that the SFP transceiver is oper-
ating correctly.
4. Check the Link mode of the SFP port if the link failed.
Co works with some ber-NICs or Media Converters,
set the Link mode to “100 Forceis needed.
l
l
- 9 -
- 10 -
5.2 Remove the module
1. Make sure there is no network activity by consult
or check with the network administrator. Or through
the management interface of the switch/converter (if
available) to disable the port in advance.
2. Remove the Fiber Optic Cable gently.
3. Turn the handle of the MFB module to horizontal.
4. Pull out the module gently through the handle.
MGB/MFB
1
2
Figure-2 Pull Out the SFP transceiver
Caution
Never pull out the module without pull the
handle or the push bolts on the module.
Direct pull out the module with violent could
damage the module and SFP module slot of
the device.
APPENDIX A
A.1 Fiber Optical Cable Connection
Parameters
The wiring details are as below:
Fiber Optical patch Cables:
Standard Fiber Type Cable Specication
100Base-FX
(1310nm) Multi-mode 50/125μm or
62.5/125μm
100Base-FX
(1310nm)
Multi-mode 50/125μm or
62.5/125μm
Single-mode 9/125μm
100Base-BX-U
(TX:1310/RX:1550)
100Base-BX-D
(TX:1550/RX:1310)
Single-mode 9/125μm

Produktspecifikationer

Varumärke: Planet
Kategori: Inte kategoriserad
Modell: MFB-TFA40

Behöver du hjälp?

Om du behöver hjälp med Planet MFB-TFA40 ställ en fråga nedan och andra användare kommer att svara dig




Inte kategoriserad Planet Manualer

Inte kategoriserad Manualer

Nyaste Inte kategoriserad Manualer