Plugwise Stealth 070155 Bruksanvisning

Plugwise Inte kategoriserad Stealth 070155

Läs nedan 📖 manual på svenska för Plugwise Stealth 070155 (3 sidor) i kategorin Inte kategoriserad. Denna guide var användbar för 8 personer och betygsatt med 4.5 stjärnor i genomsnitt av 2 användare

Sida 1/3
Be wise, plug in.
Stealth installaon
Stealth installaon guide
Also applicable to: Stealth+, Stealth M, Stealth M+
Be aware:
The Stealth is specically designed
to be built in to an appliance/lighng
xture or as a permanently connected
device in the electrical installaon of
a building. Installaon should always
be executed by a registered installer
in compliance with the local electrical
code (e.g. BS 7671 or NEC).
It is required to include an overcurrent protecve device (Circuit breaker)
before the Stealth, in the EU the maximum rang should be 16A, in North
America it should be no more than 20A. Be sure to switch o the circuit
before installing the Stealth!
The product should be installed in a closed ame retardant casing with a
proper strain-relief mechanism.
Use the L↑ labelled clamp to connect the phase wire to the appliance and
connect the neutral wire to one of the ‘Nlabelled clamps. Then connect
the incoming phase wire to the clamp labelled Land the neutral wire to
the free ‘N’ connecon.
For double phase 230V networks the second phase can be connected to the N poles
(it will not be switched).
Informaon for the installer
Technical details
Voltage: 100-240 V~ Frequency: 50 / 60 Hz Total max. current: 16 A
If a normal Stealth with relay is used, these addional maximum rangs apply:
Inducve load: 4A
Capacive load: 1A
Exceeding these rangs will adversely aect the service life of the relay!
Dimensions:
57.1 x 39 x 21 mm
ZigBee Dynamic MESH
2.4 GHz
E: helpdesk@plugwise.com T: +31(0) 252 43 30 70 W: www.plugwise.com
All specicaons without prejudice.
See www.plugwise.com for detailed informaon.
Be wise, plug in.
Stealth installaon
Stealth installaon guide
1. Insert screwdriver and move in the direcon of the arrow (up)
2. Insert wire
L L N
Appliance/ circuit
Inverter
N
L
Be aware:
Connect the L (black line) to the appliance to be measured (in this
example the inverter of the solar panel).
Be wise, plug in.
Stealth installaon
Verify the installaon
You can verify the installaon without the need of WiFi/ LAN:
Make sure you have installed the Stealth and Stretch 2.0.
Remember, the Stretch 2.0 must not be connected to LAN cable!
1. Connect the adapter with the Stretch 2.0 and the wall socket. The Stretch
2.0 will start in WiFi access point modus.
2. Connect your smartphone (installer) with the network of the Stretch via
the WiFi access point.
Password: The Stretch ID (see scker)
3. Go to : hp://192.168.40.40 via the mobile browser on your smartphone.
The Stretch 2.0 web interface starts loading and connues generang a
new appliance for the installed module.
Username: stretch
Password: The Stretch ID (see scker)
4. In case of energy producon (solar panel):
You will noce below the image of the Stealth in the green eld (and
the MAC adress) a negave sign (-) in front of the solar producon if
the installaon has been executed correctly (and if the solar panels are
producing). This may take some me. If the installaon is connected
incorrectly there will be no negave sign (-) in front of the power output.
In case of energy consumpon (appliance):
If the installaon has been executed correctly there will be no negave
sign (-) in front of the power output.

Produktspecifikationer

Varumärke: Plugwise
Kategori: Inte kategoriserad
Modell: Stealth 070155

Behöver du hjälp?

Om du behöver hjälp med Plugwise Stealth 070155 ställ en fråga nedan och andra användare kommer att svara dig




Inte kategoriserad Plugwise Manualer

Inte kategoriserad Manualer

Nyaste Inte kategoriserad Manualer