Polmar DB-50M Bruksanvisning

Polmar Marin DB-50M

Läs nedan 📖 manual på svenska för Polmar DB-50M (2 sidor) i kategorin Marin. Denna guide var användbar för 8 personer och betygsatt med 4.5 stjärnor i genomsnitt av 2 användare

Ladda ner PDF

Sida 1/2

Polmar DB-50M quick reference guide

Front panel

Dial A

R: Change channel/freq/scan dir

P: Set as main band/confirm setup

Dial B

R: Change channel/freq/scan dir

P: Set as main band/confirm setup

Vol A

R: Adjust volume

H: Delete memory channel (Hold to confirm)

Vol B

R: Adjust volume

H: Delete memory channel (Hold to confirm)

Sql

H: turn Squelch off momentarily, rotate dial to change Squelch level

Set

P: enter Set menu

H: Write/Copy Memory channel (hold Set to

confirm) or Delete Memory channel (hold

Vol to confirm)

H: Power on/off

LOW

P: Power level Low/Mid2/Mid1/High

H: Additional Signalling 5T/2T/DTMF

V/M

P: VFO mode <-> Memory mode

H: Channel spacing Wide/Middle/Narrow

P: Enable Home channel

H: Dual Watch (VFO+Memory ch) on/off

SCN

P: Scanning on/off

H: turn Skip on/off for Memory channel

MHZ

P: change dial step 1MHz/10 ch

H: Talk Around (RX/TX on repeater output)

on/off

REV

P: Frequency Reverse on/off

H: Compander on/off

TONE

P: cycle Tone/CTCSS/DCS

H: CTCSS/DCS scan (when CTCSS/DCS is on)

SUB

P: configure sub band settings

H: cycle through Scrambler settings

P: = press knob/key once, H: = hold knob/key down for 1 second, R: rotate knob

Microphone

RX: channel/frequency up

TX: Call Out

RX: channel/frequency down

TX: TBST

PTT

Transmit

0..9

RX: input memory ch/frequency

TX: send DTMF

0..9/*/#/A..D

RX: Squelch on/off

RX: input and store memory freq

PA..PD

RX: programmed keys

A/B

RX: main band A<->B

MAIN

Main band indicator

RX/TX indicators

MIC

Microphone

Speaker (when enabled in Menu 55)

RX: = press while in standby, TX: press while transmitting

Often used Menu settings

 03 – STEP: change frequency step (in VFO mode only)

 29 – NAME C: edit channel name (in Memory mode only)

 36 – RPT MOD: change repeater offset direction (or off), can also be programmed as PA..PD

 39 – SHIFT: set repeater shift in MHz (seperate settings for band A and B)

 55 – HND SPK: turn internal and hand speaker on/of

Tips and tricks

 Starting a VFO scan between a set of Lower/Upper memories scans between those frequencies only

 A and B band have seperate Home, VFO and Repeater Offset configurations, so keeping one side for 2m

(0.6MHz offset) and the other for 70cm (1.6 or 7.6MHz offset) keeps you from changing the offset when

programming repeaters.

 Set Menu 20 TBST to 1750Hz for opening repeaters.

 Set Menu 25 MUTE to off, since you can turn the volume down for the sub band if you do not want to hear

it while listening/transmitting to the main band.

 Set Menu 40 DISPLAY to Name to show the channel name and press * on the microphone keypad to turn

squelch off and display the frequency of the channel at the same time,

 Functions not available on front panel keys but available for programmable PA-PD keys are: RPTR, PRI,

TBST (also as PTT+DN), CALL OUT (also as PTT+UP).

 Set one of the programmable keys to PRI and set Menu 38 SCAN M to MSN to scan priority channels only,

now you can mark channels to scan on the fly.

 Programming the DB-50M trhough software will enable you to use other characters than A-Z, space, 0-9

for channel names (only * and # though), change the welcome text, change Home frequencies and more.

Unfortunately the programming cable is not included, but is available separately.

 The DB-50M does not turn on automatically when applying 13.8V DC.

 108-136MHz frequencies cannot be programmed/edited with the official software (frequency out of range

error, correct since the DB50M does not officially supports those frequencies), but can be stored on the

DB50 itself (and then read and written by the software). However, Menu 04 BAND needs to be set to OFF,

since otherwise you can only enter frequencies in the same band in VFO mode. You also need to set Menu

51 AUT AM to AUTO to let the radio switch to AM below 136MHz automatically or need to manually set

Menu 50 AM to ON when in VFO mode.

 The DB-50M can be programmed with Chirp (daily build, program as Anytone AT-5888UV) and can be

used to program 108-136 (AM) frequencies, but not all settings are supported. Chirp lacks the Power and

Optional Signalling and doesn’t support the use of * and # as channel name characters. But it can import

bij CSV file, something the official software can’t.

 When you use AM on band A (which can only be used on the not supported 108-136MHz and on band A

only), the DB50M will refuse to TX on VHF (on band B) and sound 5 short beeps. Using FM on band A on

any frequency does not do this.

Programmable keys suggestion

 PA: V/M, switch between VFO and memory mode

 PB: PRI, mark current main channel as Priority channel

 PC: TBST, send Tone Burst (1750Hz) to open repeater

 PD: LOW, cycle through output power settings (LOW/MID2/MID1/HIGH)

Note: reference is for Keymode 2 and opened up set only, hold Sql while powering up and select Mode 1 with

left dial knob, power cycle, then set Menu 23 Keymod to Key 2.

Produktspecifikationer

Varumärke:	Polmar
Kategori:	Marin
Modell:	DB-50M
Enhetsplacering:	Vrijstaand
Färg på produkten:	Wit
Inbyggd display:	Nee
Vikt:	50000 g
Bredd:	1285 mm
Djup:	696 mm
Höjd:	850 mm
Nettoskatt:	180 W
Ljudnivå:	41 dB
Energie-efficiëntieklasse:	D
Årlig-energiförbrukning:	185 kWu
Förpackningens bredd:	1325 mm
Djuppackning:	760 mm
Förpackningshöjd:	865 mm
Frys nettokapacitet:	300 l
Fryskapacitet:	13.5 kg/24u
Belysning inuti:	Ja
Retentionstid vid strömavbrott:	62 uur
Snabbfrysfunktion:	Nee
antal stjärnor:	4*
Temperaturlarm:	Ja
Inget frostsystem:	Nee
Larm för öppen dörr:	Nee
Klimaatklasse:	SN-T
Automatisk avfrostning (frys):	Nee
Bulleremissionsklass:	C
Ursprungsland:	China
Paket vikt:	57 kg
AC-ingångsspänning:	220 - 240 V
AC-ingångsfrekvens:	50 Hz
Energieffektivitetsskala:	A tot G