Porter-Cable FR350B Bruksanvisning
Porter-Cable
Häftapparat
FR350B
Läs nedan 📖 manual på svenska för Porter-Cable FR350B (51 sidor) i kategorin Häftapparat. Denna guide var användbar för 4 personer och betygsatt med 4.5 stjärnor i genomsnitt av 2 användare
Sida 1/51
FR350B
ROUND HEAD
FRAMING NAILER
Cloueuse de charpente à
clous à tête ronde
Clavadora para
estructuras con
cabezal redondo
www.portercable.com
INSTRUCTIVO DE OPERACIÓN, CENTROS
DE SERVICIO Y PÓLIZA DE GARANTÍA.
LÉASE ESTE INSTRUCTIVO
ANTES DE USAR EL PRODUCTO.
Française: Page 17
Español: Página 34
Instruction manual
Manuel d'instructions
Manual de'instrucciones
9R195763RA
2 - ENG
These safety glasses must
conform to ANSI Z87.1 requirements (approved glases
have “Z87” printed or stamped on them). It is the
employer’s responsibility to enforce the use of eye
protection equipment by the tool operator and other
people in the work area. (Fig. A)
(Fig. A)
(Fig. B)
[Not to
exceed 120 psi (8.3 bar).] Do not connect the tool to a
compressor rated at over 175 psi. The tool operating
pressure must never exceed 175 psi even in the event of
regulator failure. (Fig. C)
(Fig. D)
70 psi
4.9 bar
save these instructions
When using any pneumatic tool, all safety precautions, as outlined
below, should be followed to avoid the risk of death or serious injury. Read and
understand all instructions before operating the tool.
The definitions below describe the level of severity for each signal word. Please read the
manual and pay attention to these symbols.
Indicates an imminently hazardous situation which, if not avoided,
result in .
Indicates a potentially hazardous situation which, if not avoided,
result in
Indicates a potentially haz ard ous situation which, if not avoided,
result in
Used without the safety alert symbol indicates a situation which, if not
avoided, result in
3 - ENG
Never use combustible
gases or any other reactive gas as a power source for this
tool. Danger of explosion and/or serious personal injury
may result. (Fig. E)
(Fig. F)
If the contact trip is adjusted when the tool
is connected to the air supply and nails are loaded,
accidental discharge may occur. (Fig. G)
•
Do
not load fasteners with the trigger or the contact trip
depressed to prevent unintentional driving.
Do not remove spring from contact trip. Make
daily inspections for free movement of trigger and contact
trip. Uncontrolled discharge could result.
•
Leaking air, damaged parts or missing parts
should be repaired or replaced before use. Refer to
Repairs. (Fig. H)
(Fig. I)
Work safe! Respect the tool as a
working implement. (Fig. J)
•
When tool is not in use, it should be locked
in a safe place, out of the reach of children.
Produktspecifikationer
| Varumärke: | Porter-Cable |
| Kategori: | Häftapparat |
| Modell: | FR350B |
Behöver du hjälp?
Om du behöver hjälp med Porter-Cable FR350B ställ en fråga nedan och andra användare kommer att svara dig
Häftapparat Porter-Cable Manualer
26 Augusti 2024
19 Augusti 2024
Häftapparat Manualer
- Häftapparat Bosch
- Häftapparat DeWalt
- Häftapparat Whirlpool
- Häftapparat Silverline
- Häftapparat Gude
- Häftapparat Makita
- Häftapparat Hitachi
- Häftapparat Ryobi
- Häftapparat Rapoo
- Häftapparat Targus
- Häftapparat Metabo
- Häftapparat Parkside
- Häftapparat Milwaukee
- Häftapparat Hikoki
- Häftapparat Sun Joe
- Häftapparat President
- Häftapparat Einhell
- Häftapparat Kensington
- Häftapparat Proline
- Häftapparat Craftsman
- Häftapparat Meister
- Häftapparat Powerplus
- Häftapparat Genesis
- Häftapparat Fellowes
- Häftapparat Powerfix
- Häftapparat Aqua Joe
- Häftapparat Rexel
- Häftapparat Rapid
- Häftapparat Fieldmann
- Häftapparat Iluv
- Häftapparat Holzmann
- Häftapparat Surtek
- Häftapparat Dedra
- Häftapparat POWERNAIL
- Häftapparat Werckmann
- Häftapparat Neo
- Häftapparat Klein Tools
- Häftapparat Syscom
- Häftapparat MSW
- Häftapparat CTA Digital
- Häftapparat Mannesmann
- Häftapparat Smart365
- Häftapparat Total
Nyaste Häftapparat Manualer
4 Mars 2025
16 Januari 2025
17 December 2024
9 December 2024
9 December 2024
7 December 2024
15 Oktober 2024
2 Oktober 2024
1 Oktober 2024
24 September 2024