Porter-Cable PC60TPAG Bruksanvisning

Porter-Cable Slipmaskin PC60TPAG

Läs nedan 📖 manual på svenska för Porter-Cable PC60TPAG (56 sidor) i kategorin Slipmaskin. Denna guide var användbar för 2 personer och betygsatt med 4.5 stjärnor i genomsnitt av 2 användare

Ladda ner PDF

Sida 1/56

www.portercable.com

INSTRUCTIVO DE OPERACIÓN, CENTROS DE

SERVICIO Y PÓLIZA DE GARANTÍA.

ADVERTENCIA: LÉASE ESTE INSTRUCTIVO

ANTES DE USAR EL PRODUCTO.

CATALOG NUMBER

N° de catalogue

Catálogo N°

PC60TPAG

PCE829

7 amp 4-1/2 inch (114mm) angle grinder/cut off tool

Meuleuse d’angle/outil coupant de 114 mm (4 1/2 po) et de 7 A

Esmeriladora angular/cortar herramienta de 7 mperios y

114 mm (4-1/2 pulg.)

Instruction manual

Manuel d’instructions

Manual de’instrucciones

WARNING:

Read all safety warnings and all instructions. Failure to follow the

warnings and instructions may result in electric shock, fire and/or serious injury.

SAVE ALL WARNINGS AND INSTRUCTIONS FOR FUTURE REFERENCE

The term “power tool” in the WARNINGs refers to your mains-operated (corded) power

tool or battery-operated (cordless) power tool.

SAVE THESE INSTRUCTIONS

1) WORK AREA SAFETY

a) Keep work area clean and well lit. Cluttered or dark areas invite accidents.

Do not operate power tools in explosive atmospheres, such as in the presence of flammable

liquids, gases or dust. Power tools create sparks which may ignite the dust or fumes.

c) Keep children and bystanders away while operating a power tool. Distractions can cause

you to lose control.

2) ELECTRICAL SAFETY

a) Power tool plugs must match the outlet. Never modify the plug in any way. Do not use

any adapter plugs with earthed (grounded) power tools. Unmodified plugs and matching

outlets will reduce risk of electric shock.

Avoid body contact with earthed or grounded surfaces such as pipes, radiators, ranges and

refrigerators. There is an increased risk of electric shock if your body is earthed or grounded.

c) Do not expose power tools to rain or wet conditions. Water entering a power tool will

increase the risk of electric shock.

d) Do not abuse the cord. Never use the cord for carrying, pulling or unplugging the

power tool. Keep cord away from heat, oil, sharp edges or moving parts. Damaged or

entangled cords increase the risk of electric shock.

e) W

hen operating a power tool outdoors, use an extension cord suitable for outdoor

use. Use of a cord suitable for outdoor use reduces the risk of electric shock.

f) If operating a power tool in a damp location is unavoidable, use a ground fault circuit

interrupter (GFCI) protected supply. Use of a GFCI reduces the risk of electric shock.

3) PERSONAL SAFETY

a) Stay alert, watch what you are doing and use common sense when operating a power

tool. Do not use a power tool while you are tired or under the influence of drugs,

alcohol or medication. A moment of inattention while operating power tools may result in

serious personal injury.

b) Use personal protective equipment. Always wear eye protection. Protective equipment

such as dust mask, nonskid safety shoes, hard hat, or hearing protection used for appropriate

conditions will reduce personal injuries.

c) Prevent unintentional starting. Ensure the switch is in the off position before

connecting to power source and/ or battery pack, picking up or carrying the tool.

Carrying power tools with your finger on the switch or energizing power tools that have the

switch on invites accidents.

d) Remove any adjusting key or wrench before turning the power tool on. A wrench or a

key left attached to a rotating part of the power tool may result in personal injury.

e) Do not overreach. Keep proper footing and balance at all times. This enables better

control of the power tool in unexpected situations.

f) Dress properly. Do not wear loose clothing or jewelry. Keep your hair, clothing and gloves

away from moving parts. Loose clothes, jewelry or long hair can be caught in moving parts.

SAFETY GUIDELINES - DEFINITIONS

It is important for you to read and understand this manual. The information it contains

relates to protecting The symbols YOUR SAFETY and PREVENTING PROBLEMS.

below are used to help you recognize this information.

DANGER: Indicates an imminently hazardous situation which, if not avoided,

will result in death or serious injury.

WARNING: Indicates a potentially hazardous situation which, if not avoided,

could result in death or serious injury.

CAUTION: Indicates a potentially haz ard ous situation which, if not avoided,

may result in minor or mod er ate injury.

NOTICE: Used without the safety alert symbol indicates potentially hazardous

situation which, if not avoided, may result in property damage.

g) If devices are provided for the connection of dust extraction and collection facilities,

ensure these are connected and properly used. Use of dust collection can reduce dust-

related hazards.

4) POWER TOOL USE AND CARE

a) Do not force the power tool. Use the correct power tool for your application. The correct

power tool will do the job better and safer at the rate for which it was designed.

b) Do not use the power tool if the switch does not turn it on and off. Any power tool that

cannot be controlled with the switch is dangerous and must be repaired.

c) Disconnect the plug from the power source and/or the battery pack from the power tool

before making any adjustments, changing accessories, or storing power tools. Such

preventive safety measures reduce the risk of starting the power tool accidentally.

d) Store idle power tools out of the reach of children and do not allow persons unfamiliar

with the power tool or these instructions to operate the power tool. Power tools are

dangerous in the hands of untrained users.

e) Maintain power tools. Check for misalignment or binding of moving parts, breakage of

parts and any other condition that may affect the power tool’s operation. If damaged,

have the power tool repaired before use. Many accidents are caused by poorly maintained

power tools.

f) Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp cutting

edges are less likely to bind and are easier to control.

) Use the power tool, accessories and tool bits, etc. in accordance with these instructions,

taking into account the working conditions and the work to be performed. Use of the

power tool for operations different from those intended could result in a hazardous situation.

5) SERVICE

a) Have your power tool serviced by a qualified repair person using only identical

replacement parts. This will ensure that the safety of the power tool is maintained.

SAFETY INSTRUCTIONS FOR ALL OPERATIONS

SAFETY WARNINGS COMMON FOR GRINDING, SANDING,

WIRE BRUSHING OR ABRASIVE CUTTING-OFF OPERATIONS

a) This power tool is intended to function as a grinder, wire brush, sander

or cut-off tool. Read all safety warning instructions, illustrations and

specifications provided with this power tool. Failure to follow all instructions

listed below may result in electric shock, fire and/or serious injury. Operations

such as polishing are not recommended to be performed with this power

tool. Operations for which the power tool was not designed may create a hazard

and cause personal injury.

b) Do not use accessories which are not specifically designed and

recommended by the tool manufacturer. Just because the accessory can be

attached to your power tool, it does not assure safe operation.

c) The rated speed of the accessory must be at least equal to the maximum

speed marked on the power tool. Accessories running faster than their rated

speed can break and fly apart.

d) The outside diameter and the thickness of your accessory must be within

the capacity rating of your power tool. Incorrectly sized accessories cannot be

adequately guarded or controlled.

e) The arbor size of wheels, flanges, backing pads or any other accessory must

properly fit the spindle of the power tool. Accessories with arbor holes that do

not match the mounting hardware of the power tool will run out of balance, vibrate

excessively and may cause loss of control.

f) Do not use a damaged accessory. Before each use inspect the accessory

such as abrasive wheel for chips and cracks, backing pad for cracks, tear or

excess wear, wire brush for loose or cracked wires. If power tool or

accessory is dropped, inspect for damage or install an undamaged

accessory. After inspecting and installing an accessory, position yourself

and bystanders away from the plane of the rotating accessory and run the

power tool at maximum no-load speed for one minute. Damaged accessories

will normally break apart during this test time.

g) Wear personal protective equipment. Depending on application, use face

shield, safety goggles or safety glasses. As appropriate, wear dust mask,

hearing protectors, gloves and work shop apron capable of stopping small

abrasive or workpiece fragments. The eye protection must be capable of

Produktspecifikationer

Varumärke:	Porter-Cable
Kategori:	Slipmaskin
Modell:	PC60TPAG
Färg på produkten:	Black, Stainless steel
Vikt:	190 g
Sladdlängd:	1.8 m
Användarmanual:	Ja
Typ av förpackning:	Polybag
Med lås:	Ja
Ursprungsland:	Taiwan
Kabellåsspårtyp:	Kensington
Certifiering:	REACH, RoHS, Prop 65
Material:	Koolstofstaal
Antal per paket:	1 stuk(s)
Typ av kabel:	Standaard
Bästa användningen:	Notebook
Harmoniserad systemkod (HS):	83014090
Kabelns diameter:	5 mm
Slot typ:	Sleutel
Antal medföljande nycklar:	2
kabellås säkerhetsfunktioner:	T-stang
Säkerhetsöppningsankartyp:	Nano