Prima LPR601 Bruksanvisning

Prima DISKmaskiner LPR601

Läs nedan 📖 manual på svenska för Prima LPR601 (8 sidor) i kategorin DISKmaskiner. Denna guide var användbar för 3 personer och betygsatt med 4.5 stjärnor i genomsnitt av 2 användare

Ladda ner PDF

Sida 1/8

GB -1-

Chart

PROGRAMME SELECTION BUTTON

Press this button (repeatedly) until the indicator of the required programme lights

up (see “Table of programmes” below).

BUTTON

OFF

BUTTON

START BUTTON

The indicator lights up during operation, flashes when a fault occurs and goes off at

the end of the programme.

START BUTTON RESET FUNCTION

Press this button for at least 2 seconds; the selected programme and options are

cancelled. Main failure displays (repeated flashing of the START indicator lamp) can

be cancelled by RESETTING. Detailed instructions are given in chapter “What to

do if...”.

1) Programme data obtained in conformity with European standard EN 50242, obtained under normal conditions (without additional

options) and may vary depending on conditions. Differences of up to 20 minutes are possible with sensor programmes as a result of

the appliance’s automatic calibration system.

2) Reference programme for energy label in compliance with EN 50242 regulations. - Note for Testing Institutes: for detailed information

on the EN/Standard loading comparison test and other tests, contact the following address: “nk_customer@whirlpool.com”.

Table of programmes

Detergent

Consumption

PProgrammes Loading instructions Litres kWh Minutes 1)

1Pre-Wash cold Crockery to be washed later. — 5.0 0.02 10

2Quickwash 40°C Lightly soiled crockery, with no

dried-on food. * Use of tablets not

recommended. X *13.0 0.70 30

3Bio 2) 50°C Normally soiled crockery. Energy

saving programme with prolonged

drying cycle.

X 16.0 1.05 195

4Daily 60°C Normally or heavily soiled crockery. X 16.0 1.35 120

5Intensive 70°C Recommended programme for

heavily soiled crockery, especially

suitable for pots and pans.

X 17.0 1.65 145

5019 696 01535

LPR 601

BEFORE USING THE APPLIANCE FOR THE

FIRST TIME CAREFULLY READ THIS QUICK

REFERENCE GUIDE AND THE INSTALLATION

INSTRUCTIONS! THE GUARANTEE IS NOT

APPLICABLE IF FAULTS ARE CAUSED BY

INCORRECT USE OF THE APPLIANCE.

Quick reference guide

GB -2-

First time use

1- salt reservoir

2- rinse aid dispenser

3- detergent dispenser

4- racks system

5,6,7,8- available functions on the panel

9- filters

10- spray arms

In order to always ensure the best cleaning

results, you NEED to set:

DETERGENT type and WATER HARDNESS.

1. Select 3rd programme

(see Table of programmes

- page 1)

2. Press START button

for 7 seconds

3a. Check your

detergent type...

3b....and set it on your dishwasher

using the START button

(as per table below)

4. Remember to use salt and rinse

aid when needed (as indicated

below)

5. Switch off and switch on

again to save setting

Detergent

types

Dishwasher models

model without

display model with display

Powder or gel

(factory setting) no symbol add rinse aidadd salt

Tablet 2 in 1 add salt

Tablet 3 in 1

Tablet All in 1

For models without “detergent type” option, the salt and rinse aid indicators will be lit when tablets are used.

3h 6h 9h

rinse aid

salt rinse aid

1. Ask your water supply company what

the water hardness is... 2. ...enter this value on your dishwasher Suggestions for detergent use

English

degrees °eH

Water

hardness

Dishwasher with

display: insert value

in the display

Dishwasher without

display: count

START button led

flashes

Gel or Powder

(rinse aid and salt) Tabl et s

0 - 6.3 Soft 1 1x

go to step 1

(see “Daily check”)

if extra salt is

needed go to step 1

(see “Daily check”)

7 - 12.6 Medium 2 2x

13.3 - 18.9 Average 3 3x

19.6 - 25.9 Medium-hard 4 4x

26.6 - 35 Hard 5 5x

35.7 - 44.1 Very hard 6 6x

44.8 - 74.9 Extremely hard 7 7x

How to set water hardness

* only before the first wash or if the

water hardness has been changed

Switch on the appliance

- Select the 2nd programme “P2” - consult the table of programmes.

- Press the START button for at least 5 seconds until the START indicator lamp flashes.

- The water hardness setting is shown on the display (if present) or the START button flashes.

- With each successive touch of the START button the setting increases and when it reaches 7 it returns to 1 again.

- The appliance must be switched off to memorise the new setting.

Even if you use tablets which include salt,

you must still add salt since such

detergents are not effective enough at

softening hard water.

Water hardness level is factory set for

medium hard water (a number “4” is

shown on the display or the START

indicator lamp flashes 4 times).

How to set detergent type: powder/gel/tablet (if option is available)

GB -3-

Daily check

Adding rinse aid (not necessary when you use tablets). How to adjust the rinse aid dosage regulator

Daily use

The salt level indicator lamp may remain lit for the duration of several wash cycles. If the

water hardness level falls within category (soft), no salt is required.

Salt indicator

(depending on

the model)

The indicator lamp on the control panel lights

up when SALT NEEDS TO BE ADDED. orange: OK. clear: NEEDS TO BE ADDED

Rinse aid indicator (depending on model) The indicator lamp on the control panel lights up when RINSE AID NEEDS TO BE

ADDED. dark: OK. clear: NEEDS TO BE ADDED

Only use rinse aids recommended for use in domestic dishwashers. Immediately wipe away any rinse aid spilt accidentally. This prevents the formation of excess suds which can cause a fault function of the appliance.

If there are streaks: reduce the dosage by turning the dial to a lower setting (1-3). If crockery is not perfectly dry: increase the dosage by turning the dial to a higher setting (5-6). lty drying and a higher rinse aid Plastic dishes have more difficu

setting will not improve the situation.

Detergents with rinse aid incorporated may be effective only with longer programmes. In the case of shorter programmes, detergent residue may be a problem (if necessary, use powder detergent). Detergents with rinse aid incorporated tend

to form excess suds.

Visual indicator

(depending

on model).

Unscrew cap.

Fill the salt

reservoir with

water before the

first wash only.

Add salt

(never add

detergent!).