Pulse ShowerSpas 1017 Bruksanvisning

Pulse ShowerSpas Duschhuvud 1017

Läs nedan 📖 manual på svenska för Pulse ShowerSpas 1017 (4 sidor) i kategorin Duschhuvud. Denna guide var användbar för 2 personer och betygsatt med 4.5 stjärnor i genomsnitt av 2 användare

Ladda ner PDF

Sida 1/4

Installation Instructions

Bonzai Rain Shower System

Model # 1017

Invigorate. Decorate. Rejuvenate.

ongratulations on your purchase of a Bonzai PULSE Showerspa. We take great pride

in the styling, quality and workmanship of this product. With proper installation and

care, your Showerspa will give you a showering experience like never before. Get

ready to start your day in a whole new way and FEEL THE PULSE!

Figure F

Pos. 1 Pos. 2 Pos. 3

Figure B

# Part Description Qty. # Part Description Qty.

escutcheon base plate w/tape 1

15.

wall anchor pin/nail - (optional) 2

½ inch x 2½ inch brass nipple 1

16.

handle 1

90° connector w/cone washer 1

17.

handshower holder 1

tapered plastic compression washer 1

18.

hexagon washer 1

chrome finned compression nut 1

19.

stainless steel washer 1

escutcheon cover

20.

#4 X 5/8" Philips head screw

18 in.

(46 cm )

PVC supply line

21.

59 in.

(1.5M )

PVC handshower hose

2.5gpm.

(9.5lpm )

flow restrictor

22.

4mm round handshower washer

rubber washer with screen

23.

handheld shower w/check valve

10.

° Showerspa supply Inlet

24.

6mm round showerhead washer

11.

wall mount w/adhesive tape

25.

8 in.

(200m m )

rain showerhead

12.

#4 X 5/8". Philips head screw

26.

ABS shelf

13.

wall mount cover plate

27.

#4 X 1/2" Philips head screw

14.

mushroom wall anchor - (optional) 2

28.

"Optional" thin escutcheon 1

1280mm

77.1mm

470mm

49.2mm

Figure C

5mm hole

(3/16 inch)

Figure D

Figure E

Optional - drilled wall anchor

Figure A

2 3

13 14 15

14 15

18 19 20

Thank you for choosing the

Bonzai Rain Shower System Model #1017

By PULSE Showerspas Inc.

stallation of the Bonzai Rain Shower System is designed to be quick and easy. If you have any installation

issues or

performance problems, call

technical support toll free at 888-785-7320 or email support@pulseshowerspas.com before

returning this product

. For helpful installation video go to: http://www.pulseshowerspas.com/flash/bonzai_installation.html

Please read instructions carefully to become familiar with components

, installation procedures and tools required. [Figure A]

Follow steps in the order

presented to avoid mistakes

What

is needed: Philips screwdriver, adjustable wrench, level, pencil/marker, Isopropyl alcohol.

What may be needed

: Cordless drill, 3/16” inch (5mm) masonry/tile drill bit, hammer, hair dryer

Determine general mounting lo

cation: The Bonzai is designed to easily mount in virtually any shower or tub/shower configuration!

With

a two handled valve (separate handle for hot & cold) we suggest installing the Bonzai centered between the two handles. With a single

handle valve

, the Bonzai can be mounted above the valve (typical tub/shower configuration) or on either side of the valve. The unique pivoting

shower arm and adjustable body sprays ensure perfect positioning!

Getting started:

Remove the showerhead and escutcheon (trim cover) from your existing shower arm.

Determine minimum length NPT nipple (2) required:

a) Place a mark on existing shower arm at the wall surface.

b) Unscrew shower arm from elbow in wall.

c) Measure distance from mark made on shower arm to end of shower arm threads that were previously inserted in wall.

d) Add ½ inch to this measurement, and then round up to nearest ½ inch. (i.e. if measurement = 1¾ inches, add ½ inch = 2¼ inches, rounded up

to nearest ½ inch = 2½ inch NPT nipple. This is the minimum length required with maximum length to be plus 1 inch.

NOTE If supplied 2½ inch nipple (2) is not the correct length based on above formula, you must obtain correct size - sold separately. :

Apply generous amount of Teflon tape and/or pipe sealant to nipple (2) and adequately tighten into elbow in wall to ensure no leaks. Do not damage

or mar final ½ inch of nipple threads protruding from wall.

Insert rubber washer with screen (9) into hexagon fitting of supply line (7) and connect to 90° inlet (10). Do not over-tighten.

Slide female wall mounts (11) over their male counterparts. [Figure B] NOTE: Do not remove covering on special adhesive tape!

Hold Bonzai up to the wall and determine mounting location; evaluating showerhead and body spray heights making certain supply line (7) reaches

NPT nipple (2). Use a level to check for vertical (plumb) position. It is ideal to position entire surface area of mounts (11) on flat, non-porous surface.

(i.e. no grout lines or uneven surfaces.) Once confident of Bonzai’s position, mark the wall at top & bottom mounts (11) for reference.

Mounting locations on wall must be thoroughly cleaned of all residues with a 50:50 mix of Isopropyl alcohol and water. The area must be

completely dry before adhering mounts to wall surface. Ideal application temperature is 70 F or above and no less than 60 F° ° .

Remove covering of special adhesive tape on wall mounts (11) and carefully position Bonzai onto wall at predetermined location.

IMPORTANT: Apply a consistent firm pressure equal to 15psi against the wall surface for at least 1 minute.

NOTE: At 70 F approximately 50% of ultimate bond strength will be achieved after 20 minutes, 90% after 24 hours and 100% after 72 hours. °

Ultimate bond strength can be achieved more quickly (and in some cases bond strength can be increased) by exposure of the bond to elevated

temperatures (e.g. 150ºF (66ºC) for 1 hour. A common hair blow dryer can be used to accelerate the cure time

Carefully slide the Bonzai out of the female wall mounts while the tape bonds to wall surface. If using this drill-less installation technique, it is highly

recommended to wait at least 24 hours before continuing the installation (Step #12) or introducing any moisture.

10.

To further secure mounts (11) with nylon wall anchors (14) in solid surface walls (tile, marble, granite etc.) use a 3/16 inch (5mm) masonry/tile drill bit

and slowly drill a 1¼ inch (32mm) deep hole through existing hole of female mounts. CAUTION: live (active) plumbing is behind the wall!

NOTE: If mounting Bonzai with wall anchors through a fiberglass wall you must purchase appropriate type mounting anchors (Qty 2) for this type of

wall surface. – sold separately. PULSE does not recommend mounting through fiberglass wall surfaces without adequate wood or sheetrock backing!

11.

Insert nylon anchor (14) through the female mount (11) making sure mushroom head is seated firmly against mount and mount is firmly seated

against wall. Using a hammer, tap nail (15) into nylon anchor body until flush with nylon head. [Figure C]

12.

Remove covering of two faced tape on escutcheon base plate (1) and slide over nipple (2) securing base plate to wall. NOTE: Optional thin

escutcheon (28) is provided for installations where the ABS escutcheon (6) interferes with desired mounting height of Showerspa.

HINT: For best finished look when using thin escutcheon (28), nipple should only extend ½-¾ inch (12-19mm) from wall surface.

13.

Secure 90° connector with cone washer (3) to nipple. Do not over-tighten. [Figure D] NOTE: Cone washer is already installed on 90° connector.

14.

Insert Bonzai into wall mounts. Determine length of supply line (7). Supply line must install completely over barbed portion of 90° connector (3). To

shorten, remove Bonzai from wall and cut supply line with sharp utility knife.

15.

Re-insert Bonzai into wall mounts, slide compression nut (5) followed by tapered end of compression washer (4) over supply line hose (7). Push

hose onto barbed portion of 90° connector (4) and secure with compression washer and nut. Do not over-tighten. Push escutcheon cover (6) into

base plate (1). [See Figure E] HINT: Apply small amount of liquid soap to help hose slide onto barbed connection.

16.

Select mounting hole for required spacing from wall and secure with Philips head screws (12). Do not over-tighten. Insert chrome covers (13) into

mounts to hide screws. [See Figure F]

17.

Thread handle (16) into left side of hand shower mount. Align hanger (17) on right side followed by hexagon washer (18), round washer (19) and

secure with screw (20).

18.

Insert 4mm rubber washer (22) into each end of hand shower hose (21) and secure to Bonzai and hand shower (23).

19.

Insert 6mm washer (24) into shower head (25) and securely tighten to Bonzai.

20.

Carefully insert ABS shelf (26) into mounting bracket until tabs lock in place. Secure shelf to Bonzai body with Philips screw (27)

21.

You are now ready to enjoy your new Bonzai Rain Shower System by PULSE Showerspas, Inc.

Produktspecifikationer

Varumärke:	Pulse ShowerSpas
Kategori:	Duschhuvud
Modell:	1017
Färg på produkten:	Wit
Vikt:	415 g
Förpackningens vikt:	548 g
Förpackningens bredd:	65 mm
Djuppackning:	180 mm
Förpackningshöjd:	197 mm
Antal hastigheter:	2
Laddningstid:	1 uur
Vattentät:	Ja
Bakgrundsbelysning:	Ja
Användningstid:	40 min
Blöt och torr:	Ja
Tvättbar:	Ja
Minsta hårlängd:	0.5 mm
Antal pincett:	40 pincetten
Rakapparat:	Ja
Lämplig för kort hår:	Ja
Flytande huvud:	Ja
Massagefunktion:	Ja
Batterityp:	Ingebouwd