Pyle PMX802M Bruksanvisning

Pyle Stavmixer PMX802M

Läs nedan 📖 manual på svenska för Pyle PMX802M (9 sidor) i kategorin Stavmixer. Denna guide var användbar för 14 personer och betygsatt med 4.5 stjärnor i genomsnitt av 2 användare

Ladda ner PDF
Sida 1/9
Mul-Channel Mixers
PyleUSA.com
Warnings
Please be sure to read, keep and refer to instrucons listed in this manual.
Do not use this device near water or expose to moisture.
Clean only with a dry cloth.
Do not block any venlaon openings and allow adequate space for air ow during operaon.
Do not install near any heat sources or other devices that produce heat.
Do not defeat the safety purpose of the polarized or grounding-type plug.
Protect the power cord from any kind of damage or corrosion.
Unplug the mixer when not in use or when unused for long periods of me.
Refer all service to qualied service personnel. Servicing is required when the mixer has been damaged or performs in an unusually.
Use only speaker cables when connecng speakers to amplier outputs. Using other types of cables is a re hazard.
Exposure to extremely high noise levels may cause in permanent hearing loss. Individuals vary considerably to noise induced hearing loss but
take precauon when listening at high levels.
If the power cord is damaged (i.e., cut or a bare wire is exposed), ask your dealer for a replacement. Using the unit with a damaged power cord
is a re and electrical shock hazard.
Should this unit be dropped or the cabinet be damaged, turn the power switch o, remove the power plug from the AC outlet, and contact your
dealer. If you connue using the unit without heeding this instrucon, re or electrical shock may result.
C A U T I O N
If the unit is damaged or non-operaonal, please nofy your dealer and the shipping company immediately. Claims for
damage or replacement may not be granted if not reported properly or in a mely manner.
Connect this unit’s power cord only to an AC outlet of the type stated in this Manual or as marked on the unit. Failure to do so may result in
re and/or electrical shock.
Do not place heavy objects on top of the power cord. A damaged power cord is also a re and electrical shock hazard.
Use only the included power cord for this unit, using other types may again result in re and electrical shock.
Do not set all equalizer controls and faders to maximum levels. Doing so may cause oscillaon depending on the condion of the connected
unit and speakers, and may also damage the speakers.
The performance of components on this mixer such switches, rotary controls, faders, and connectors, deteriorates over me. The rate as
depends on the operang environment and is somemes unavoidable. Consult your dealer about replacing defecve components.
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT ATTEMPT TO OPEN OR ACCESS THE INSIDE OF
THE UNIT. REFER ALL SERVICING TO A QUALIFIED PYLE
SERVICE PERSONNEL.
This lightning ash symbol is intended to alert the user to the presence of uninsulated and “dangerous
voltage” within the mixer's enclosure that may be of sucient power to constute a risk of electric shock.
This exclamaon point symbol is intended to alert the user to the presence of important operang
and maintaining instrucons, that one should pay aenon to and keep for future reference.
Mul-Channel Mixers
PyleUSA.com
Installaon
Install the mixer on an even surface to allow for sucient airow and venlaon during use. The device is equipped with
electronically controlled cooling fans to protect against thermal overload and internal circuitry from damage due to
extreme heat. Please avoid covering any sides of the unit or placing objects or other audio devices too close to your mixer.
Prior to connecng and powering on the unit, make sure that the device matches the voltage and frequency of your
power supply. Power o the mixer when not in use.
Cables and Connecons
RCA
1/4'' TRS and Mono
XLR 3-Pin
RCA connector jacks have been most
commonly used in home audio systems
and conguraons for years. Also known
as RCA 'phono', 'plugs' or 'audio
connectors' , these jacks are always
unbalanced, and generally carry a line-
level signal at 10 dB, nominal signa–l
levels. The RCA connector jacks are most
likely used when connecng an audio
device like a media player or other home
audio type source to your mixer. These
connector jacks are also used when
connecng to the output of your devices.
1/4'' mono and stereo connector jacks are
labeled for use as unbalanced mono,
unbalanced stereo, balanced mono, or as
an insert patch point. A 1/4'' TRS (Tip,
Ring, Sleeve), 3-conductor connecon, or
'Stereo' cable allows a single connecon
signal to carry 2-channels of audio; also
can be used for mono balanced signals.
While, a 1/4'' TS (Tip, Sleeve), 2-conductor,
or 'Mono' cable are most popularly known
for their use in guitar or line-level
instrument connecon; they can also be
used for mono unbalanced signals.
XLR connector jacks, almost always carries
a balanced signal. Depending on your
device, these connector jacks may also be
capable of handling unbalanced signals.
Microphones generally have this type of
connector, as well as most other
professional audio equipment and devices.
Typical 3-Pin XLR sockets are xed with the
right-most pin being the 'ground', the le-
most pin being 'hot' and the boom pin
as the 'neutral'.
Technical Specicaons
Mono Inputs
Microphone Inputs (XENYX Mic Preamp)
XLR, electronically balanced, discrete input circuit
Mic E.I.N. (20Hz - 20kHz)
@ 0 Ohm Source Resistance
@50 Ohm Source Resistance
@150 Ohm Source Resistance
-134dB / 135.7dB A-Weighted
-131dB / 133.3dB A-Weighted
-129dB / 130.7dB A-Weighted
Frequency Response
<10Hz - 150kHz (-1dB)
<10Hz - 200kHz (-3dB)
Gain Range
+10dB to +60dB
Maximum Input Level
+12dB @ +10dB Gain
Impedance
Approximately 2.6k Ohm, Balanced
Signal- -Noise to
110dB / 112dB A-Weighted
Distoron (THD +N)
0.005% / 0.004%, A-Weighted
Line Input
1/4'' TRS Connectors, Electronically Balanced
Channel Equalizaon
(Frequency Hz)
Control Range High: @ 10k +/-15dB
Control Range Low: k +/-15dB @60
Master 5-Band Graphic EQ
Frequency: Hz (60, 250, 1K, 4K, 12K)
Control Ranges: +/-12dB

Produktspecifikationer

Varumärke: Pyle
Kategori: Stavmixer
Modell: PMX802M

Behöver du hjälp?

Om du behöver hjälp med Pyle PMX802M ställ en fråga nedan och andra användare kommer att svara dig


Stavmixer Pyle Manualer

Pyle

Pyle PMUX9 Bruksanvisning

6 December 2024
Pyle

Pyle PMUX6 Bruksanvisning

6 December 2024
Pyle

Pyle PMAX4 Bruksanvisning

10 September 2024
Pyle

Pyle PMAX6 Bruksanvisning

9 September 2024
Pyle

Pyle PMAX8 Bruksanvisning

7 September 2024
Pyle

Pyle PMIDIPD20 Bruksanvisning

26 Augusti 2024
Pyle

Pyle PMX6BU Bruksanvisning

13 Augusti 2024
Pyle

Pyle PMX802M Bruksanvisning

11 Augusti 2024

Stavmixer Manualer

Nyaste Stavmixer Manualer

Alto

Alto PBM4 Sistema Bruksanvisning

16 Januari 2025
Alto

Alto L-12 Bruksanvisning

16 Januari 2025
Alto

Alto S-12 Bruksanvisning

16 Januari 2025
Alto

Alto DJM-2 Bruksanvisning

16 Januari 2025
Alto

Alto S-16 Bruksanvisning

16 Januari 2025
Alto

Alto APM80.1000 Bruksanvisning

16 Januari 2025
Alto

Alto AMX-120 Bruksanvisning

16 Januari 2025
Alto

Alto S-8 Bruksanvisning

16 Januari 2025
Alto

Alto LYNX-MIX82 Bruksanvisning

16 Januari 2025
Alto

Alto DJM-3 Bruksanvisning

16 Januari 2025