QTX TETRA Bruksanvisning

QTX Lättnad TETRA

Läs nedan 📖 manual på svenska för QTX TETRA (6 sidor) i kategorin Lättnad. Denna guide var användbar för 12 personer och betygsatt med 4.5 stjärnor i genomsnitt av 2 användare

Sida 1/6
www.avsl.com 1.608 User Manual 15 UK
TETRA
4- -1 LIGHT EFFECT in
Item ref: 1.608 15 UK
User Manual
Version 2.0
Caution: Please read this manual carefully before operating
Damage caused by misuse is not covered by the warranty
www.avsl.com 1.608 User Manual 15 UK
Introduction
Thank you for your purchase of e QTX light effect. This model can deliver an extra wide array of th TETRA
colourful projections coupled with powerful UV/strobe and laser effects. Please read and keep this user
manual to get the best from your purchase and avoid damage through misu se
Warning
To prevent the risk of fire or electric shock, avoid contact with moisture or humid environment s.
No user serviceable parts insid Do n open the case refer all servicing to qualified service personnel. e ot
Caution: Laser radiation
Avoid pointing directly towards eyes. Laser output can cause injury if viewed directly.
This product is a Class 3B laser and should only be installed and used by persons who
are trained in the management of laser radiation and are able to operate in
accordance within the guidance given by the Health and Safety Executive (HSE) in
HS(G)95: The Radiation Safety of Lasers used for Display purposes”. Copies of this
guide can be downloaded from: www.avsl.com/assets/documents/hsg95.pdf
Safety
Check for correct mains voltage and condition of power lead before connecting to power outlet. a
Placem t en
Use the included mounting bracket to fix to a stand or lighting truss
Use secondary safety fixings if mounting overhead.
Ensure adequate airflow around the fixture housings
Ensure adequate access to controls and connections
Cleaning
Use a soft cloth with a neutral d ergent to clean the casing as required et
Do not use strong solvents for cleaning the unit
In the box
Please open the package carefully and check that all contents are pres t and in good condition. en
Contact your retailer if any part is missing or broken.
TETRA LED & laser light effect
I.R. remote control
Mounting bracket
Laser keys (x2)
UK mains plug to C lead IE
Please do not open cover, contains high voltage. This product is
not serviceable or repairable by the end user. Please refer to
qualified personnel for service and repair.
www.avsl.com 1.608 User Manual 15 UK
Rear panel
Installation
Install the TETRA free standing on a stable surface or suspen from a lighting stand or truss. ded
When mounting to a stand or truss, use the included adjustable fixing bracket and ensure that a safety wire is
used if mounting overhead.
If the TETRA is to be operated by DMX control, connect the DMX control signal to th DMX IN connector using e
a XLR lead and connect further DMX fixtures being controlled from the DMX OUT connector. n
Connect mains power to the TETRA using the supplied IEC lead or equivalent, ensuing the supply voltage is
correct and capable of the load demand.
Remote control
The TETRA is supplied wit an infra-red remote control for quick operation. h
This is powered by a CR2025 button cell, which should be engaged by pulling out the plastic tab.
Point the remote towards the front of the TETRA housing, where the I.R. receiver is located.
The remote controls are explained in the diagram below
Laser Key
OFF
ON

Produktspecifikationer

Varumärke: QTX
Kategori: Lättnad
Modell: TETRA

Behöver du hjälp?

Om du behöver hjälp med QTX TETRA ställ en fråga nedan och andra användare kommer att svara dig




Lättnad QTX Manualer

Lättnad Manualer

Nyaste Lättnad Manualer