Rikon 30-251 Bruksanvisning

Rikon Borrmaskin 30-251

Läs nedan 📖 manual på svenska för Rikon 30-251 (20 sidor) i kategorin Borrmaskin. Denna guide var användbar för 4 personer och betygsatt med 4.5 stjärnor i genomsnitt av 2 användare

Ladda ner PDF
Sida 1/20
34 Floor Radial Drill Press”
www.rikontools.com
30-251M4
Operator’s Manual
Record the serial number and date of purchase in your manual for future reference.
Serial Number: _________________________ Date of purchase: _________________________
For technical support or parts questions, email techsupport@rikontools.com or call toll free at (877)884-5167
The serial number can be found on the specication label on the rear of your machine.
IMPORTANT! Safety is the single most important consideration in the operation of this equipment. The following
instructions must be followed at all times.
There are certain applications for which this tool was designed. We strongly recommend that this tool not be modied and/
or used for any other application other than that for which it was designed. If you have any questions about its application,
do not use the tool until you have contacted us and we have advised you.
General Safety Warnings
KNOW YOUR POWER TOOL. Read the owner’s manual carefully. Learn the tool’s applications, work capabilities, and its
specic potential hazards.
ALWAYS KEEP VISITORS AWAY FROM RUNNING MACHINES.
All visitors should be kept a safe distance from the work area.
ALWAYS MAKE THE WORKSHOP CHILDPROOF.
Childproof with padlocks, master switches, or by removing starter keys.
NEVER OPERATE A TOOL WHILE UNDER THE INFLUENCE OF DRUGS,
MEDICATION, OR ALCOHOL.
ALWAYS WEAR PROPER APPAREL.
Never wear loose clothing or jewelry that might get caught in moving parts. Rubber-soled footwear is
recommended for the best footing.
ALWAYS USE SAFETY GLASSES AND WEAR HEARING PROTECTION.
Also use a face or dust mask if the cutting operation is dusty.
NEVER OVERREACH.
Keep your proper footing and balance at all times.
ALWAYS GROUND ALL TOOLS.
If your tool is equipped with a three-pronged plug, you must plug it into a three-hole electric receptacle.
If you use an adapter to accommodate a two-pronged receptacle, you must attach the adapter plug to a
known ground. Never remove the third prong of the plug.
ALWAYS AVOID DANGEROUS ENVIRONMENTS.
Never use power tools in damp or wet locations. Keep your work area well lighted and clear of clutter.
ALWAYS REMOVE THE ADJUSTING KEYS AND WRENCHES FROM TOOLS AFTER USE.
Form the habit of checking to see that keys and adjusting wrenches are removed from the tool before
turning it on.
ALWAYS KEEP YOUR WORK AREA CLEAN. Cluttered areas and benches invite accidents.
NEVER STAND ON TOOLS.
Serious injury could occur if the tool is tipped or if the cutting tool is accidentally
contacted.
2
SAFETY INSTRUCTIONS
ALWAYS CHECK FOR DAMAGED PARTS.
Before initial or continual use of the tool, a guard or other part that is damaged should be checked to
assure that it will operate properly and perform its intended function. Check for alignment of moving
parts, binding of moving parts, breakage of parts, mounting, and any other conditions that may a󰀨ect its
operation. A guard or other damaged parts should immediately be properly repaired or replaced.
ALWAYS DISCONNECT TOOLS.
Disconnect tools before servicing and when changing accessories such as blades, bits, and cutters.
ALWAYS AVOID ACCIDENTAL STARTING.
Make sure switch is in “OFF” position before plugging in cord.
NEVER LEAVE TOOLS RUNNING UNATTENDED.
Special Safety Rules For Drill Press
SAVE THESE INSTRUCTIONS.
Refer to them often.
3
1. Do Not operate the Drill Press until it is assembled
and you have read the instructions.
2. Do Not operate the Drill Press unless you are familiar
with its safe operation. If you are not familiar with
the operation of a Drill Press seek advice from your
supervisor, instructor or other qualied individual.
3. If you are using a bench top Drill Press, it must be
securely fastened to a stand or bench.
4. If you are operating a oor Drill Press it must be
securely fastened to the oor.
5. Always clear the table and work area before turning
on the Drill Press.
6. Always use drill bits, cutting tools and accessories
with a 1/2” shank or less.
7. Never place hands near the drill bit, cutting tool or
accessory.
8. Never wear loose clothing, gloves or ties while
operating the Drill Press.
9. Always have a rm footing while operating the Drill
Press.
10. Always keep work surface and work areas clear of
debris.
11. Never attempt to do set-up work, assembly or layout
work on the Drill Press while it is in operation.
12. Never start the Drill Press with the drill bit, cutting
tool or accessory in contact with the work-piece.
13. Always lock all table, column and head locks before
turning on the Drill Press.
14. Never operate the Drill Press with a damaged drill
bit, cutting tool or accessory.
15. Always check the drill bit, cutting tool or accessory
in tight in the chuck.
16. Never operate the Drill Press with the chuck key in
the chuck.
17. Always adjust the depth stop to avoid drilling into
the table surface.
18. Never drill material unless it is properly supported.
Non at work-pieces require additional support.
19. Always clamp the work piece to the table.
20. Always support large work-pieces at the same height
as the table.
21. Never remove the work-piece or clear the table until
the Drill Press comes to a complete stop.
22. Always wear a face shield and safety glasses while
operating the Drill Press.
23. Never operate the Drill Press with missing, damaged,
worn, loose or defective parts.
24. Never adjust, change speeds or perform
maintenance on the Drill Press while it is operating.
25. Always clean the work surface and work area when
nished operating the Drill Press.
26. Always disconnect the power when adjusting or
performing maintenance on the Drill Press.
27. Always disconnect the power when nished using
the Drill Press to prevent accidental operation.
This machine is intended for the of wood, composite materials, plastics, ferrous and non-ferrus metalsdrilling .
The permissible workpiece dimensions must be observed (see Technical Specification). Any other use not
as specified, including modification of the machine or use of parts not tested and approved by the equipment
manufacturer, can cause unforeseen damage and invalidate the warranty.
ATTENTION: Use of this drill press still presents risks that cannot be eliminated by the manufacturer.
Therefore, the user must be aware that wood working machines are dangerous if not used with care and all
safety precautions are adhered to.

Produktspecifikationer

Varumärke: Rikon
Kategori: Borrmaskin
Modell: 30-251

Behöver du hjälp?

Om du behöver hjälp med Rikon 30-251 ställ en fråga nedan och andra användare kommer att svara dig


Borrmaskin Rikon Manualer

Rikon

Rikon 30-100 Bruksanvisning

28 December 2024
Rikon

Rikon 30-251 Bruksanvisning

28 December 2024
Rikon

Rikon 30-240 Bruksanvisning

28 December 2024
Rikon

Rikon 30-212VS Bruksanvisning

28 December 2024
Rikon

Rikon 30-217 Bruksanvisning

28 December 2024
Rikon

Rikon 30-140 Bruksanvisning

28 December 2024
Rikon

Rikon 30-230 Bruksanvisning

18 September 2024

Borrmaskin Manualer

Nyaste Borrmaskin Manualer

DeWalt

DeWalt DW9106 Bruksanvisning

31 December 2025
Gude

Gude GTB 16/12 R+L Bruksanvisning

31 December 2025
Metabo

Metabo BS 12 BL Q Bruksanvisning

31 December 2025
Milwaukee

Milwaukee M12 BDDXKIT Bruksanvisning

30 December 2025
Herkules

Herkules SB 1625/1D Bruksanvisning

30 December 2025
Global

Global AS-G 18/1 Bruksanvisning

30 December 2025
Global

Global AS-G 18 Bruksanvisning

30 December 2025
Global

Global AS-G 12 Bruksanvisning

30 December 2025
Global

Global LED-ASG 18 Bruksanvisning

30 December 2025
Netter Vibration

Netter Vibration NCT 1 Bruksanvisning

29 December 2024