Rockford Fosgate Punch P1652-S Bruksanvisning

Läs nedan 📖 manual på svenska för Rockford Fosgate Punch P1652-S (12 sidor) i kategorin Inte kategoriserad. Denna guide var användbar för 2 personer och betygsatt med 4.5 stjärnor i genomsnitt av 2 användare

Sida 1/12
01/2009 B.M.
02/2009 E.R.
1230-55479-01 Printed in China
Serial Number: Date of Purchase:
Installation & Operation
Installation et fonctionnement
Instalación y funcionamiento
Einbau und Betrieb
Installazione e funzionamento
Component Systems
P152-S 5.25˝
P1652-S 6.5˝
P1T-S Tweeter System
Rockf d Corporation offers a limited warranty on Rockfor ord Fosgate products on the following terms:
Length of Warranty
Speakers – 1 Year. Any Factory Refurbished Product – 90 days (receipt required)
What is Covered
This war pplies onlranty a y to Rockford Fosgate products sold to consumers by Authorized Rockf d For osgate
Dealers in the United States of America or its possessions. oduct purPr chased by consumers from an
Authorized Rockf d Fosgate Dealer in another countror y are covered only by that countrys Distributor and
not by Rockford Corporation.
Who is Covered
This warranty covers only the original purchaser of Rockford product purchased from an Authorized
Rockford Fosgate Dealer in the United States. In order to receive ser the purchaser must prvice, ovide
Rockford with a copy of the receipt stating the customer name, ,dealer name product purchased and date of
purchase.Products found to be def e during the warectiv ranty period will be repaired or replaced
(with a product deemed to be equivalent) at Rockford's discretion.
What is Not Covered
1. Damage caused by accident, waterabuse oper operations,, impr , theft, shipping
2.Any cost or expense related to the removal or reinstallation of product
3. Service performed by anyone other than Rockford or an Authorized Rockford Fosgate Service Center
4.Any product which has had the serial number defaced, emoaltered, or r ved
5. Subsequent damage to other components
6.Any product purchased outside the U.S.
7.Any product not purchased from an Authorized Rockf d Fosgate Dealeror
Limit on Implied Warranties
Any implied warranties including warranties of fitness for use and mer e limited in duration to thechantability ar
period of the express warranty set forth above. Some states do not allow limitations on the length of an implied
warranty,so this limitation may not apply. No person is authorized to assume for Rockford Fosgate any other
liability in connection with the sale of the product.
How to Obtain Service
Contact the Authorized Rockf d Fosgate Dealer you purchased this product fr If you need further or om.
assistance or Rockf d Customer Ser, call 1-800-669-9899 f or vice.You must obtain an RA# (Return
Authorization number) to return any product to Rockf d For osgate.You are responsible for shipment
of product to Rockford.
EU Warranty
This product meets the current EU warranty r see yequirements, our Authorized dealer for details.
2009 Rockf d Corporation. eseror All rights r ved.
Rockf d Fosgate and the Rockf d For or osgate logo are either
registered trademarks or trademarks of Rockf d Corporation.or
L WIMITED ARRANTY ST
ATEMENT
Rockford Fosgate
Rockf d Corporationor
600 South Rockford Drive
Tempe,Arizona 85281 U.S.A.
In U.S.A., (480) 967-3565
Customer Service 1-800-669-9899
www.rockfordfosgate.com
2
Before beginning any installation, follow these simple rules:
1. Be sure to carefully read and understand the instructions before attempting to
install these speakers.
2. For safety, disconnect the negative lead from the battery prior to beginning the
installation.
3. For easier assembly, we suggest you run all wires prior to mounting your speakers
in place.
4. Use high quality connectors for a reliable installation and to minimize signal or
power loss.
5. Think before you drill! Be careful not to cut or drill into gas tanks, fuel lines,
brake or hydraulic lines, vacuum lines or electrical wiring when working on any
vehicle. If installation in a boat, take care not to cut or drill through the main hull.
6. Never run wires underneath the vehicle. Running the wires inside the vehicle or
hull area provides the best protection.
7. Avoid running wires over or through sharp edges. Use rubber or plastic
grommets to protect any wires routed through metal, especially the firewall.
1. Determine where the speakers will be mounted. Ensure an area large enough for
the speaker to mount evenly. Be sure that the mounting location is deep enough
for the speaker to fit; if mounting in a door, operate all functions (windows, locks,
etc.) through their entire operating range to ensure there is no obstruction.
2. Refer to the specification chart to determine the proper diameter hole to cut
for your speaker model.The template provided also gives the proper cutout size.
3. Mark the locations for the mounting screws. Drill the holes with a 1/8" bit.
4. Feed the speaker wires through the cutout and connect to the speaker terminals.
Be sure to observe proper polarity when connecting the wires.The speaker's
positive terminal is indicated with a "+".
5. On models with slotted holes, fit the speaker into the cutout and install the
screws in the slots at the top and bottom.This will allow you to rotate the speak-
er to match the remaining mounting holes.When aligned, tighten the screws.
6. Tighten the screws until the speaker is snug in place to prevent rattling. Do not
over tighten the screws.
NOTE: If needed use the adapter plate provided to mount the speaker. See
Adapter Plate Templates at the end of this manual.
SAFETY
CARTON CONTENTS
CAUTION: Before installation, disconnect the battery
negative (-) terminal to prevent damage
to the unit, fire and/or possible injury.
(1) Set P1 Series Speakers with Tweeters or
P1T-S Tweeter System with Crossover
(1) Set of grilles/trim rings
Mounting Hardware and Tweeter Surface,Angle, and Flush Mounts
INSTALLATION ONSIDERATIONSC
MOUNTING
Cutout
Hole
Position to
Align Holes
Example of standard r installation doo
Use tip of a small flat
screwdriver to re e tweemov ter
Example of Discreet al Cla ™) Du mp (DDC
Tweeter Mounting (Flush Mount)
Panel
PRACTICE SAFE SOUND™
Continuous exposure to sound pressure levels over 100dB may
cause permanent hearing loss. High powered auto sound systems
may produce sound pressure levels well over 130dB. Use common
sense and practice safe sound.
IN – Connect from Amplifier From Amplifier
TWT – Connect to Tweeter
1/4”
(0.25”) 3/16”
(0.1875”)
P1T-S – System Connection
0dB
-2dB
-4dB
3
Specifications subject to change without notice.See figures on following pages.
P1 Components P152-S P1652-S P1T-S
Nominal Diameter - inch (mm) 5.25 (133.35) 6.5 (165.10) 1.0 (25.0)
Description 2-Way 2-Way Tweeter Kit
Nominal Impedance (ohms) 4 4 4
Frequency Response (Hz) 70Hz-22kHz 60Hz-22kHz 3.5kHz-22kHz
Crossover Frequency (Hz) 3.5kHz 3.0kHz 3.0kHz
12dB/octave Butterworth Crossover HP (High Pass) HP (High Pass) HP (High Pass)
Voice Coil Diameter - inch (mm) 1.0 (25.4) 1.0 (25.4)
Fs - Free Air Resonance (Hz) 70Hz 60Hz 3.5kHz
Qts 0.68 0.68
Vas - cu. ft. (Liter) 0.19 (5.4) 0.60 (16.8)
Xmax - inch (mm) 0.1 (2.5) 0.14 (3.5)
SPL (dB @ 1w/1m) 87dB 89dB 90dB
Power Handling-Watts (RMS / Peak) 50/100 60/120 60/120
Mounting Diameter-inch (mm) 4.81 (122.21) 5.57 (141.35) 1.75 (44.40) (Flush Mount)
Mounting Depth-inch (mm) 1.87 (47.50) 2.17 (55.00) 0.91 (23.14) (Flush Mount)
Includes Grille/Trim Ring YES YES YES
Trim Ring Diameter-inch (mm) 6.22 (158.00) 6.97 (177.00) 2.10 (53.34)
Trim Ring Height-inch (mm) 0.88 (22.34) 0.83 (21.00) 0.30 (7.66)
Includes Adapter Plate 5"x7"/6"x9" 5"x7"/6"x9" NO
SPECIFICATIONS
WIRING
FEATURES
Discreet Dual Clamp (DDC™)
Tweeter Mount
Every aspect of the new Tweeter design has been
completely re-engineered to allow for maximum
ease of installation and fitment.This optimized
patent pending design provides concentric
clamping pressure around the perimeter of the
mounting hole.
The “mounting cups” are in fact not “cups” at all,
but rather unobtrusive “clampsthat quickly
and easily mount in a standard 1.75 inch (45mm)
hole saw opening with a single center screw
securing with balanced pressure to both faces
of the mounting surface. From there, the tweeter
simply snaps into place and is secured by a
snap-on trim ring. Removal is easy if needed.
The protective grille on the tweeter is
non-removable and an intergral part of the design.
ICC (Integrated Concealed Crossover)
For the P152-S and P1652-S, the crossover is
integrated into the basket of the mid-bass driver.
This component grade crossover allows for easy
connection of the full component system without
the need for an external crossover. Just connect
the wires from the tweeter to the TWT
terminals at the speaker, see below.
P1T-S Crossover Wiring
1. Use illustration for proper connection.
2. Be sure to maintain speaker polarity.
3. Connecting the positive wire to 0dB matches the amplitude of the tweeter to the speaker.
4. Connecting the positive wire to -2dB or -4dB reduces the amplitude of the tweeter -2dB
or -4dB lower than the midrange, (ideal for tweeters located high in door panels and
midranges located low in the kick panel).
Tweeter
Crossover

Produktspecifikationer

Varumärke: Rockford Fosgate
Kategori: Inte kategoriserad
Modell: Punch P1652-S

Behöver du hjälp?

Om du behöver hjälp med Rockford Fosgate Punch P1652-S ställ en fråga nedan och andra användare kommer att svara dig




Inte kategoriserad Rockford Fosgate Manualer

Inte kategoriserad Manualer

Nyaste Inte kategoriserad Manualer