Ruckus Wireless ZoneFlex 7372 Bruksanvisning
Ruckus Wireless
Åtkomstpunkt
ZoneFlex 7372
Läs nedan 📖 manual på svenska för Ruckus Wireless ZoneFlex 7372 (4 sidor) i kategorin Åtkomstpunkt. Denna guide var användbar för 4 personer och betygsatt med 4.5 stjärnor i genomsnitt av 2 användare
Sida 1/4
Copyright © 2013 Ruckus Wireless, Inc. Page 1 of 4
Published January 2013, Part Number 800-70415-001 Rev E
ZoneFlex 7352/7372 802.11n
Multimedia Wi-Fi Access Point
Quick Setup Guide
This Quick Setup Guide provides step-by-step instructions on
how to set up your Ruckus Wireless ZoneFlex Access Point. After
completing the steps described in this Guide, you will be able to
place the Access Point (AP) at your site and provide wireless
network access to users.
BEFORE YOU BEGIN
Before deploying Ruckus Wireless products, please check for the
latest software and the release documentation.
• User Guides and Release Notes are available at
http://support.ruckuswireless.com/documents.
• Software Upgrades are available at
http://support.ruckuswireless.com/software.
• Open Source information is available at
http://opensource.ruckuswireless.com.
• Software License and Limited Warranty available at
http://support.ruckuswireless.com/warranty.
PACKAGE CONTENTS
• ZoneFlex 7352/7372 Access Point
• Mounting screws and anchors (2)
• Security screw (1)
• 15/16-inch T-bar clips (2)
• Alignment spacer (1)
• Regulatory flyer
• Declaration of Conformity (country-dependent)
• Product Warranty Statement
• This Quick Setup Guide
SETUP REQUIREMENTS
• A computer running Windows 7 (procedures for other OS’s
are similar)
• One or more of the following:
• A modem (DSL or cable), broadband router, or other
device provided by your Internet Service Provider that
brings Internet access to your site.
• A network switch or a DSL/Internet gateway device.
• Two Ethernet cables (Cat5e or better for PoE in)
• An AC power adapter (sold separately), or
• An 802.3af or 802.3at -compliant Power over Ethernet (PoE)
switch or PoE injector
S TEP 1: CONNECT THE AP TO YOUR COMPUTER
1After removing your Ruckus Wireless AP from its package,
place it next to your computer.
2Using an Ethernet cable, connect your computer’s network
port to the 10/100/1000 port on the AP.
3Using the AC adapter (sold separately), connect the AP to a
convenient (and protected) power source.
• Alternatively, connect the 10/100/1000 port to a PoE
injector or PoE switch for both power and network con-
nectivity.
4Verify that the Power LED on the external enclosure is a
steady green.
STEP 2: PREPARE YOUR COMPUTER FOR AP
SETUP
1On your Windows 7 computer, configure your network
adapter from the Local Area Connection settings as follows:
•Start > Control Panel > Network and Sharing
Center > Change Adapter Settings
2Edit the TCP/IPv4 address settings as follows:
•Local Area Connection > Properties > Internet
Protocol Version 4 (TCP/IPv4) > Properties
The TCP/IPv4 Properties dialog box appears.
3Select Use the following IP address (if it is not already
selected) and then make the following entries:
•IP address: 192.168.0.22 (or any address in the
192.168.0.x network)
•Subnet mask: 255.255.255.0
•Default gateway: 192.168.0.1
Leave the DNS server fields empty.
4Click OK to save your changes.
Your changes are put into effect immediately.
S TEP 3: LOG INTO THE AP
As specified earlier, the AP should be directly connected to your
computer (through the Ethernet port) and powered on, ready for
setup.
1On your computer, open a Web browser window.
2In the browser, type this URL to connect to the AP:
https://192.168.0.1
3Press <Enter> to initiate the connection. When a security
alert dialog box appears, click OK/Yes to proceed.
4When the Ruckus Wireless Admin login page appears, enter
the following:
•Username: super
•Password: sp-admin
5Click Login.
IMPORTANT!
If the AP is deployed with a ZoneDirector, follow the
ZoneDirector Quick Setup Guide, and connect the AP to your
local network.
NOTE:
The following procedures assume Windows 7 as the operating
system. Procedures for other OS’s are similar.
IMPORTANT!
Write down all of the currently active settings so you can
restore your computer to its current configuration later (when
this process is complete).
Copyright © 2013 Ruckus Wireless, Inc. Page 2 of 4
Published January 2013, Part Number 800-70415-001 Rev E
S TEP 4: CUSTOMIZE THE W SIRELESS ETTINGS
1On the Web interface menu, click Configuration > Wire-
less (Configuration > Radio 2.4G or Configuration > Radio
5G for the ZoneFlex 7372). The Configure :: Wireless :: Com-
mon options appear.
2Verify that the following options are active:
•Channel: SmartSelect
•Country Code: If you are not located in the United
States, select your current country.
3Click Update Settings if you made any changes.
4Click any of the eight “Wireless #” tabs at the top of the
page.
5In Wireless Availability, click Enabled.
6Delete the text in the SSID field, and then type a name for
your network that will help your users identify the AP in their
wireless network connection application.
7Click Update Settings to save your changes.
8Repeat Steps 4-7 for each Wireless # interface that you want
to enable.
9Click Logout to exit the Web interface.
10 Disconnect the AP from the computer and from the current
power source, and then restore your computer to its original
network connection configuration.
S TEP 5: PLACE THE AP IN YOUR SITE
1Move the AP to its permanent location (accessible to both
AC power and network connection).
2Use an Ethernet cable to connect the 10/100/1000 port of
the AP to your network.
3Connect the AC power adapter (or PoE power supply) to the
AP, then to a convenient power source.
4Verify that the 10/100/1000 port LED is lit.
After a short pause to re-establish the Internet connection, you
can test the AP.
STEP 6: VERIFY THE INSTALLATION
1Using any wireless-enabled computer or mobile device,
search for and select the wireless network you previously
configured.
2If you can connect, open a browser and link to any public
Web site.
Congratulations! Your wireless network is active and ready for
use.
(O IPTIONAL) MOUNTING NSTRUCTIONS
The ZoneFlex 7352/7372 can be mounted to a wall, ceiling or to
a T-bar using the supplied mounting screws or the T-bar clips
built into the bottom of the AP enclosure.
Mounting to a Flat Surface
1Use this Quick Start Guide template or the alignment spacer
to mark the locations for screw holes on the mounting sur-
face. Use a 5mm drill bit to drill approximately 25mm into
the mounting surface.
2Insert the anchors and mounting screws into the mounting
surface, leaving approximately 0.28” (7 mm) of the screw
heads protruding for the AP enclosure.
The screws should be approximately 3.25” (82.6 mm) apart
per the template.
3Insert a straightened paperclip (or similar) into the hole on
the side of the AP (Figure 1.), to release the locking mecha-
nism.
Figure 1. Insert a paperclip into the pinhole
4Place the AP onto the mounting screws so that the screw
heads enter the mounting holes on the AP enclosure, and
push the AP downward to lock in place.
5Remove the paperclip to release the lock mechanism and
secure the AP.
6To unmount, insert a straightened paperclip into the hole on
the side of the AP to unlock, then push the AP upward to
release the AP enclosure from the mounting screws.
Mounting to a T-Bar
The ZoneFlex 7352/7372 provides mounting options for flush tile
and recessed frame T-bars in acoustical ceiling tiles.
Flush Tile
1Orient the AP so that the T-bar is positioned between the T-
bar clips as shown in Figure 2., then rotate the AP until the
third T-bar clip catches the T-bar and the latch locks the T-bar
in place (Figure 3.).
Figure 2.
Figure 3.
Default AP Settings (For Your Reference)
Network Names
(SSIDs)
Wireless1—Wireless8 (2.4GHz radio)
Wireless9—Wireless16 (5GHz radio,
ZoneFlex 7372 only)
Security (Encryption
method)
Disabled for each wireless interface
Default Management
IP Address
192.168.0.1
NOTE:
If you will be using PoE, you will need a Cat5e (or better)
Ethernet cable to connect the AP to the PoE injector or switch.
Hold paperclip in
while mounting
Security screw
hole
Copyright © 2013 Ruckus Wireless, Inc. Page 3 of 4
Published January 2013, Part Number 800-70415-001 Rev E
2Insert the Torx-head security screw into the hole near the
latch to lock in place.
3To remove the unit, first remove the security screw, then
depress the latch while rotating the AP so that the T-bar clips
disengage the T-bar.
Recessed Frame
The enclosed T-bar clips support mounting to recessed frame
drop ceiling T-bars.
1Fasten T-Bar clips (included) to the T-Bar.
2Twist the two T-bar clips onto the acoustical ceiling T-bar.
Adjust the height of the anchor sleeves such that the anchor
heads extend just below the ceiling tile surface. Anchor
sleeves can be adjusted to accommodate frame recess
depths up to 6mm.
3Clip the alignment spacer between the two T-bar clip/anchor
sleeve assemblies.
4Insert a straightened paperclip (or similar) into the pinhole
on the side of the AP and hold in place while mounting (see
Figure 4.).
5Place the AP over the anchor sleeves such that the heads
enter the mounting holes on the AP enclosure, and slide the
AP to lock in place.
6Remove the paperclip to release the lock mechanism and
secure the AP.
7To remove the AP, insert a straightened paperclip into the
hole on the side of the AP to unlock, and then slide the AP
to release the AP enclosure from the mounting screws.
Figure 4. Recessed frame T-bar mounting
FOR MORE INFORMATION
You can now use the wireless network to log into the AP’s Web
interface. Use the Web interface to review and fine-tune a wide
range of AP settings. For information on how to configure the AP
from the Web interface, refer to the Ruckus Wireless ZoneFlex
Indoor Access Point User Guide or the Online Help, available
from within the Web interface.
NOTE:
If the T-bar clips slide easily along the T-bar, use a piece of
Scotch tape or similar to secure them in place while mounting
the AP. The tape may be removed once the AP is mounted.
Hold paperclip in
while mounting
Produktspecifikationer
| Varumärke: | Ruckus Wireless |
| Kategori: | Åtkomstpunkt |
| Modell: | ZoneFlex 7372 |
Behöver du hjälp?
Om du behöver hjälp med Ruckus Wireless ZoneFlex 7372 ställ en fråga nedan och andra användare kommer att svara dig
Åtkomstpunkt Ruckus Wireless Manualer
17 September 2024
17 September 2024
17 September 2024
17 September 2024
17 September 2024
17 September 2024
17 September 2024
17 September 2024
17 September 2024
17 September 2024
Åtkomstpunkt Manualer
- Åtkomstpunkt Bosch
- Åtkomstpunkt Huawei
- Åtkomstpunkt Allnet
- Åtkomstpunkt Allied Telesis
- Åtkomstpunkt Airlive
- Åtkomstpunkt Edimax
- Åtkomstpunkt Renkforce
- Åtkomstpunkt Sitecom
- Åtkomstpunkt TP Link
- Åtkomstpunkt Fortinet
- Åtkomstpunkt Totolink
- Åtkomstpunkt Cisco
- Åtkomstpunkt Engenius
- Åtkomstpunkt Netis
- Åtkomstpunkt Digitus
- Åtkomstpunkt Draytek
- Åtkomstpunkt Linksys
- Åtkomstpunkt Buffalo
- Åtkomstpunkt Dahua Technology
- Åtkomstpunkt Netgear
- Åtkomstpunkt LevelOne
- Åtkomstpunkt Dell
- Åtkomstpunkt Planet
- Åtkomstpunkt ZyXEL
- Åtkomstpunkt Zebra
- Åtkomstpunkt D-Link
- Åtkomstpunkt Aruba
- Åtkomstpunkt Tenda
- Åtkomstpunkt Ubiquiti Networks
- Åtkomstpunkt Trendnet
- Åtkomstpunkt Mikrotik
- Åtkomstpunkt EQ3
- Åtkomstpunkt Hawking Technologies
- Åtkomstpunkt INCA
- Åtkomstpunkt Moog
- Åtkomstpunkt Moxa
- Åtkomstpunkt StarTech.com
- Åtkomstpunkt Advantech
- Åtkomstpunkt Intellinet
- Åtkomstpunkt Lancom
- Åtkomstpunkt SMC
- Åtkomstpunkt Aerohive
- Åtkomstpunkt V7
- Åtkomstpunkt Media-tech
- Åtkomstpunkt NUVO
- Åtkomstpunkt Cudy
- Åtkomstpunkt IP-COM
- Åtkomstpunkt Meru
- Åtkomstpunkt Amped Wireless
- Åtkomstpunkt Cambium Networks
- Åtkomstpunkt 3Com
- Åtkomstpunkt AMX
- Åtkomstpunkt Bintec-elmeg
- Åtkomstpunkt Mach Power
- Åtkomstpunkt Brocade
- Åtkomstpunkt ICC
- Åtkomstpunkt Insteon
- Åtkomstpunkt Juniper
- Åtkomstpunkt Comtrend
- Åtkomstpunkt Premiertek
- Åtkomstpunkt Extreme Networks
- Åtkomstpunkt Atlantis Land
- Åtkomstpunkt Mojo
- Åtkomstpunkt FlyingVoice
- Åtkomstpunkt Luxul
Nyaste Åtkomstpunkt Manualer
26 Oktober 2024
26 Oktober 2024
26 Oktober 2024
18 Oktober 2024
18 Oktober 2024
18 Oktober 2024
14 Oktober 2024
13 Oktober 2024
12 Oktober 2024
11 Oktober 2024