Rupert Neve Designs Portico II Bruksanvisning

Rupert Neve Designs Processor Portico II

Läs nedan 📖 manual på svenska för Rupert Neve Designs Portico II (22 sidor) i kategorin Processor. Denna guide var användbar för 10 personer och betygsatt med 4.5 stjärnor i genomsnitt av 2 användare

Ladda ner PDF
Sida 1/22
1
Operations Manual
By:
Serial #:
2
Portico II Channel User Guide
Thank you for your purchase of a Portico II Channel module.
Everyone at Rupert Neve Designs hope you enjoy using this tool as much as we have enjoyed
designing and building it. The name “Portico II” will be used for a series of new ultra-high end
professional products that will share some traits. Please take note of the following list of safety concerns
and power requirements before the use of this or any Portico II Series product.
Safety
It’s usual to provide a list of “do’s and don’ts” under this heading but mostly these amount to
common sense issues. However, here are important safety requirements that must be adheared to:
Heat generated by the Channel module is radiated through the case work and by convection through the
ventilation holes, therefore the holes should not be covered or blocked. To avoid overheating,
Portico II units should not be stacked immediately above or adjacent to other equipment that
gets hot, and one rack space above the unit should be left open for heat ventilation.
Also bear in mind that other equipment may radiate strong hum elds which could spoil
the performance of your Portico II module.
Protect the power cord from being walked on or pinched, particularly at plugs convenience receptacles
and the point where they exit from the apparatus. Do not defeat the safety purpose of the polarized or
grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type
plug has two blades and a third grounding prong. The wide blade or the third prong are provided for
your safety. Unplug the module during lightning storms or when unused for long periods of time.
Don’t operate your Portico II module in or around water! Electronic equipment and liquids are not
good friends. If any liquid is spilled, such as soda, coffee, alcoholic or other drink, the sugars and
acids will have a very detrimental effect. Sugar crystals act like little rectiers and can produce
noise (crackles, etc.). SWITCH OFF IMMEDIATELY because once current starts to ow the
mixture hardens, can get very hot (burnt toffee!) and cause permanent and costly damage. If it gets
wet and you suspect that good clean water may have gotten in, immediately unplug the unit, and
remove it from the source of water. Please contact support as soon as possible at
support@rupertneve.com for resolution. Clean only with dry cloth.
Don’t be tempted to operate a Portico II unit with the cover removed. The cover provides magnetic
screening from hum and R.F. stray elds.
Power Requirements
Each Portico II unit has a high quality, low noise switching power supply that is further ltered and shunt
regulated for an exceptionally quiet and reliable power source for the audio circuits. The power sup-
ply is considered “universal” in the sense that it will accept 100V through 240V AC and complies with
standard mains voltages around the world. Be absolutely sure to disconnect mains power (remove the
power cable from the IEC power connector at the back panel) before checking the fuse. The fuse is lo-
cated in the IEC power input connector and is accessed by opening the small panel labeled “FUSE”. The
fuse should always be replaced with the correct value and type. The Portico II power supply requires a
5x20 mm 2.5 amp fast acting ceramic body fuse Bussman type GDA 2.5A or equivalent.
3
The fuse is a protection device intended to prevent additional damage or hazard if the Portico II unit de-
velops a problem. However sometimes a fuse may “pop” due to a mains surge and need to be replaced
(it probably did protect the Portico II). The symptom of a blown fuse is simply that the unit does not
power up. Disconnect the power cable, try replacing the fuse, re-insert the power cable, push the “Pow-
er” button. If this does not solve the problem or the fuse “pops” again there may be a problem with the
Portico II you should contact your dealer or email < > or support@rupertneve.com phone 512-847-3013.
Gain
0-66dB
DI
Detect
Line Trim
+/-6dB
HPF
In
EQ Pre / Post
EQ Compressor
Phase
Reverse
LF In
LMF / HMF
In HF In
GR METER
Comp In
Silk
Silk +
Texture
Mute
Output
METER
Send
Return
LinkSidechain
All EQ
In
From
Sidechain
To
Sidechain
S/C
HPF
HPF
(Auto)
De-ess
HMFLMF HF
LF
Output
+48V
PORTICO II
CHANNEL STRIP
Portico II Channel: Block Diagram

Produktspecifikationer

Varumärke: Rupert Neve Designs
Kategori: Processor
Modell: Portico II

Behöver du hjälp?

Om du behöver hjälp med Rupert Neve Designs Portico II ställ en fråga nedan och andra användare kommer att svara dig


Processor Rupert Neve Designs Manualer

Rupert Neve Designs

Rupert Neve Designs Portico II Bruksanvisning

27 September 2024
Rupert Neve Designs

Rupert Neve Designs Portico 543 Bruksanvisning

9 Augusti 2024

Processor Manualer

Nyaste Processor Manualer

Toa

Toa DP-K1 Bruksanvisning

21 Oktober 2024
Eventide

Eventide UltraTap Bruksanvisning

2 Oktober 2024
Helix

Helix DSP ULTRA Bruksanvisning

26 September 2024
Helix

Helix DSP.3S Bruksanvisning

26 September 2024
Helix

Helix DSP ULTRA S Bruksanvisning

26 September 2024
MyMix

MyMix RX-2 Bruksanvisning

25 September 2024
Henry Engineering

Henry Engineering AES DigiSwitch 3X1 Bruksanvisning

25 September 2024
SPL

SPL Transient Designer 9946 Bruksanvisning

25 September 2024
SPL

SPL M/S Master Bruksanvisning

25 September 2024
Bose

Bose ControlSpace CC-16 Bruksanvisning

25 September 2024