Ruwido Easytip 1 Bruksanvisning

Läs nedan 📖 manual på svenska för Ruwido Easytip 1 (19 sidor) i kategorin Fjärrkontroll. Denna guide var användbar för 10 personer och betygsatt med 4.5 stjärnor i genomsnitt av 2 användare

Sida 1/19
SOLUTIONS IN INFRARED & ELECTRONICS.
User Manual
991 425 00
Bedin ET1 Version 1 07.03.2001 14:28 Uhr Seite 1
Norsk Suomi Svenska Nederlands Italiano Français Deutsch English
123
6
5
4
789
0
AV
P
P
a
b
c
d
f
e
h
i
g
Contents
Introduction page 4
Inserting and changing the batteries page 5
Description of keys page 5
Programming easytip page 5
Querying the Code Numbers page 6
Changing the acoustic signals page 7
Inhaltsverzeichnis
Einleitung Seite 4
Einsetzen und Wechseln der Batterien Seite 5
Tastenbeschreibung Seite 5
Einstellen des easytip Seite 5
Auslesen der Code-Nummer Seite 7
Ändern der akustischen Signale Seite 7
Table des matières
Introduction page 12
Insertion et remplacement des piles page 13
Description des touches page 13
Réglage de l’easytip page 13
Lecture du numéro de code page 15
Changement des signaux acoustiques page 15
Indice
Introduzione pagina 20
Inserimento e sostituzione delle batterie pagina 21
Descrizione tasti pagina 21
Impostazione del easytip pagina 21
Lettura del codice pagina 23
Selzione dei segnali acustici pagina 23
Inhoud
Inleiding pag. 16
Aanbrengen en vervangen van de batterijen pag. 17
Beschrijving van de toetsen pag. 17
Instellen van de easytip pag. 17
Lezen van de codenummers pag. 18
Veranderen van de akoestische signalen pag. 18
Innehåll
Inledning sida 28
Isättning och byte av batterier sida 29
Beskrivning av tangenter sida 29
Inställning av easytip sida 29
Kodläsning sida 30
Ändring av akustiska signaler sida 31
Sisällysluettelo
Johdanto siva 8
Paristojen asennus ja vaihto
siva 9
Näppäinten kuvaus siva 9
e
asytipin ohjelmointi
siva 9
Ohjelmointi koodin selaushaun avulla
siva 10
Äänimerkkien muuttaminen siva 11
Innholdsfortegnelse
Innledning side 12
Innsetting og utskifting av batterier side 13
Beskrivelse av tastene side 13
Å stille inn easytip side 13
Å lese av koden side 14
Å endre de akustiske signalene side 15
INDEX
Bedin ET1 Version 1 07.03.2001 14:28 Uhr Seite 3
Inserting and changing the batteries
Your easytip is powered by two (alkaline) 1.5 V batteries (IEC LR 03,
AAA)
Insert the batteries following the markings in the battery compartment.
If the acoustic signal does not sound as usual when pressing the keys
or if the device you are controlling fails to respond from the usual di-
stance then the batteries must be changed.
Do not remove the old batteries from the remote control until new ones
are available. The residual charge will maintain your code settings.
Be careful not to press any of the keys when you are changing batteries,
otherwise easytip will lose the data held in its memory.
Easytip`s memory function may fail if the batteries are defective, or
cannot be replaced in time. If this happens you will need to reenter the
codes (it is a good idea to keep a note of the codes in the operating
manual).
Please dispose batteries carefully.
Description of keys
Image
a number keys: 0-9
b -/--: single/double digit enter, 10,1-
cAV: AV input (e.g. VCR, SAT)
dP+/P-: switch to next/previous channel
e+/- Vol: Volume control
f Mute: Sound on/off
gPower/standby: on/off
hTeletext on
i Teletext off
Programming easytip
Programming by Code entering
1. Switch on your TV set.
2. Turn to the TV code list (other manual) and look for the name of your
TV manufacturer.
3. Press keys -/--(image b) and Teletext off (image i) together until the
acoustic signal sounds twice.
4. Enter the first 3-digit code from the list with the number keys
(image a) on your remote control.
ATTENTION!
The first figure of the 3-digit code must be entered within 5 seconds of
the acoustic signal sounding twice.
Otherwise the acoustic signal will sound once and you will have to
repeat the procedure from step 3.
5. After the 3-digit code has been entered the acoustic signal will sound
twice to indicate that the code has been accepted.
ATTENTION!
If you entered the first digit within 5 seconds but still hear one long bleep
after you have entered the code, this means the code you entered is in-
valid.
In this case, repeat the procedure from step 3.
6. Now point your easytip at your TV set and press the Power/Standby-
key (image g). Easytip is set up correctly if the TV set switches off.
7. If your TV set does not react to the TV code number you entered or if
it operates incorrectly, enter the next number listed against the TV
manufacturer`s name.
The TV code list shows the most common codes first.
Introduction
The Next Generation ñ Universal Remote Control
Congratulations purchasing easytip, the universal infrared remote con-
trol for your TV set.
Easytip is a product of high quality
All information on this product is published with no consideration for
possible patent rights. Trademarks are mentioned without guarantee of
their free use.
Although a lot of care was taken when creating this manual with its text
and graphic images, errors can never be completely eliminated.
Therefore, the manufacturer cannot be made liable for faulty statements
and their possible consequences.
You are very welcome to contact the manufacturer for report errors and
to make suggestions for improvement.
© 1999 by ruwido
All rights reserved, including rights of photomechanical reproduction and
electronic storage.
Printed in Austria.
ruwido-austria
Köstendorfer Straße 8
A-5202 Neumarkt am Wallersee
tel. +43(0)6216/4571
fax +43(0)6216/457126
e-mail: service.easytip@ruwido.com
Internet: http://www.ruwido.com
5
English
4
English
Bedin ET1 Version 1 07.03.2001 14:28 Uhr Seite 4

Produktspecifikationer

Varumärke: Ruwido
Kategori: Fjärrkontroll
Modell: Easytip 1

Behöver du hjälp?

Om du behöver hjälp med Ruwido Easytip 1 ställ en fråga nedan och andra användare kommer att svara dig




Fjärrkontroll Ruwido Manualer

Fjärrkontroll Manualer

Nyaste Fjärrkontroll Manualer