Sagemcom D142 Bruksanvisning

Sagemcom Telefon D142

Läs nedan 📖 manual på svenska för Sagemcom D142 (2 sidor) i kategorin Telefon. Denna guide var användbar för 2 personer och betygsatt med 4.5 stjärnor i genomsnitt av 2 användare

Ladda ner PDF

Sida 1/2

D142

NTRODUCTION

Dear customer,

Thank you for purchasing a Sagemcom DECT telephone we appreciate your trust in us.

This product was manufactured with the utmost care, should you encounter difficulties during its use we

recommend that you refer to this user guide. You can also find information on the following site:

http://www.sagemcom.com

For your comfort and safety, we ask that you read the following section carefully :

ECOMMANDATIONS ET CONSIGNES DE SECURITE

Your DECT telephone must not be installed in a humid room (wash-up room, bathroom,

laundry room, kitchen, etc.) unless it is 1.50 m away from a water point or outside. Your

telephone must be operated at temperatures ranging from 5°C and 45°C.

Only use the supplied power adapter, connect it to the base socket according to the

installation instructions provided in this booklet and the indications on the identification

label affixed to it (voltage, current, electric network frequency). As a precaution, in case

of danger, the mains adapters act as a disconnecting mechanism for the 230V power

supply. They should be placed near the device and should be easily accessible.

This telephone was designed for use on the public switched telephone network (PSTN).

In case of a problem you must first contact your reseller. Only use the supplied

telephone cord.

For your personal safety, never place your handset on the base without the batteries,

or without the battery cover, you could get an electric shock.

To avoid damaging your handset, only use certified rechargeable AAA batteries NiMH

1.2 V 400 mAH, never use non rechargeable batteries. Insert the batteries in the handset

battery compartment respecting polarity.

At the end of their useful life, batteries must be disposed of according to the recycling

instructions presented in this booklet.

Your DECT telephone has an inside radio range of about 50 metres and up to

300 metres in open space. The immediate presence of metal parts, (of a television for

example), of any electric appliance may result in range reduction.

Some sensitive medical equipment and safety equipment may be affected by the radio-

frequency transmissions of your telephone. In all cases, we ask that you respect the

safety recommendations.

In areas where storms are frequent, we recommend that you protect your telephone line

using a surge protection device .

This equipment does not function in the case of an electric network shutdown: for

emergency calls, it is recommended to use another unit during power cuts.

The CE marking certifies that the product meets the essential requirements of Directive

1999/5/CE of the European Parliament and of the Council pertaining to microwave radio

equipment and telecommunication terminal equipment, for the safety and health of

users, for electromagnetic interference. Furthermore, it efficiently uses the frequency

spectrum attributed to ground and spatial communication to prevent damaging

interference.

The declaration of compliance may be looked up on the www.sagemcom.com site

"support" section or can be obtained from the following address :

Sagemcom Broadband SAS

250, route de l'Empereur - 92848 Rueil-Malmaison Cedex - France

D142

EFORE YOU BEGIN

Make sure your package includes the following: Base unit, handset, one battery compartment cover,

telephone line cord, AC power supply, two rechargeable batteries, and this user guide.

In the case of purchasing a pack duo or trio, you will find in addition for each additional handset: a

handset charger, one battery compartment cover, two rechargeable batteries.

Installing the phone

Paging button

- Pressed briefly : telephone set paging.

- Hold down pressed (4 seconds minimum) :

telephone set registration.

Rechargeable

batteries

Power socket

Telephone socket

1. Insert the batteries, taking care to respect the polarity as indicated in the compartment.

2. Put the compartment door back on. «SEARCHING...» appears on the screen.

3. Connect the end of the mains power unit lead to the bottom of the base and the mains power unit to

the mains socket.

4. Plug the power supply cord into AC outlet and the other end into the power jack on the base bottom.

5. A welcome message in all the languages supported by the telephone is displayed on the screen,

press OK *.

You will hear a confirmation tone.

Place the handset in the base station to charge for 15 hours prior to first use.

6. After charging, press key. You can hear dial tone.

* :

depending on country

D142

Handset keys

Intercom key

Earpiece

Red key:

Talk off /

Switch handset on/off

Access to phonebook /

Navigation key down

Navigation key up /

Access the caller list

Deactivate / Activate handset

ringer (Press and hold)

Microphone

Screen

Access to outgoing call list

Menu key

OK key:

Selection / Validation

Green key:

Talk on

ctivate, deactivate keypad lock

(Press and hold)

R key:

Second call / conference

Back key / Cancel /

Correction /

Change standby screen

(Press and hold)

Mute:

ctivate / Deactivate the microphone

Quick guide to handset display icons

Signal strength icon (blinking when no signal or the signal strength is weak).

Call (blinks when you receive a call)

Voicemail icon: indicates that new messages are present in your voicemail box.

Handset ringer muted.

Received call list (appears when a new call is in the caller list).

Memory.

Charging status icon ( : Full ; + flashing (charger not connected) : Flat; blinking

during charging).

Changing the batteries

Make sure the telephone is OFF before you replace batteries.

1. Remove the batteries compartment door.

2. Remove old batteries.

3. Insert the batteries in the handset battery compartment respecting polarity.

4. Put the batteries compartment door back on.

5. Place handset in the base to charge.

D142

ENU STRUCTURE

Quick reference

phonebook New entry Clock&alarm date / time

List Set format

Edit entry Alarm

delete Alarm tone

delete all

Directe mem. Advanced set Change pin

registration

Unregister

contry

reset

Personal set Handset name AUTO PREFIX

Handset tone Recall time

LANguage Dial mode

Auto hang-up First ring

Navigation

To navigate among the menus, use the keys: MENU, , or OK and .

Example: To change the ring tone, go to the menu Personal set / Handset tone / ring tones.

To do this:

1. Press MENU. Select " Personal set " using the  or key.

2. Press OK. Select " Handset tone " using the  or key.

3. Press OK. Select "ring tones " using the  or key.

4. Press OK. 10 melodies are available: " melody 1 "… " melody 10 ".

Select the desired melody using the or key.

5. Press OK key to confirm your selection.

ALLS

Make a call

Ensure that the handset is switched on.

1. Press the Talk key .

You will hear the dialling tone and the display will show you the phone icon .

2. Enter the phone number.

- OR-

1. Enter the phone number first and then press key.

D142

Answering a call

When the phone rings, press the key to answer the call.

You can adjust the volume of what you hear through the handset at any time by

pressing  or ҏkey.

Ending a call

To end a call press .

Microphone mute function

-Enable MUTE function: press the key. The display shows "mute on".

-Disable MUTE function: press the key. Your correspondent can hear you again.

Voice Mail (According to operator)

With this function you can receive calls in your absence on a voice message recorder in the switched

telephone network. To indicate that a new message has been received the envelope icon and the

new event message "

voicmail

" are displayed on the Handset screen.

Your voicemail number is not set in the factory.

- Dial the number of your operator’s voice message recorder.

- The envelope icon disappears when there are no more new messages.

ALL LOG

Calling line identification presentation (CLIP)

This CLIP phone stores and displays CLIP information provided by your local telephone company.

You must subscribe to CLIP service in order to use this unit.

If you have not subscribed to CLIP service or if the caller number is suppressed, the display shows

“unknown”.

Display of numbers not available:

UnUnav

avava

aail

ililab

abable

lele

: you are not in same area as your contact.

HiHide

dede

idid

: your contact does not want their number to be displayed.

Received call log

The received call log presents the calls you received. (max.10 last calls).

6. Press , the icon is displayed.

7. The most recent name or call number is displayed according to whether your contact's number is

included in your phonebook or not.

8. Press OK to display the date and the time of the call.

9. Press the or  key to go through the list.

If the number is too long (more than 12 digits), the screen will not show the number

in full.

Press OK key to go to last number page for CID length.

D142

Diallled call log

The dialled call log presents the calls you made (max. 5 last calls).

To consult the list:

1. Press briefly .

2. The last dialled number is displayed.

Press the









key to consult the list of the last 5 numbers dialled.

Calling back a caller

1. Press the or key.

2. Press the or  key to select a call record.

3. Press the key to dial the number.

Making an entry in the directory from the list of calls received.

1. Press the or key.

2. Use   or to select the desired caller number.

3. Press MENU key, then select "save number ".

4. Enter the name of the entry. Press OK.

Deleting caller list record

1. Press the or key.

2. Press or  key to select a call record.

3. Press MENU.

- Select " delete " to delete the current record.

- Select " delete all " to delete the entire Caller list.

4. A confirmation screen appears.

5. Using the telephone touch keys:

- If you do not wish to delete the current record, press .

- .To confirm the deletion of the entry, press OK

HONEBOOK

You can store 50 phonebook entries (24 digits and 12 characters) in your phonebook.

Dialling a memory number

1. Press key to consult the list of contacts.

2. Press theor  key to consult directory entries.

3. When you have selected the desire number, press .

Creating / Storing a memory

1. Go to the menu " phonebook " / " new entry "

2. Enter the name of the entry. Press OK.

3. Enter the number of your entry using the keypad keys. Press OK.

Editing a memory

1. Go to the menu " phonebook " / " edit entry ".

2. Select the entry you want to edit using or . Press OK.

D142

3. You will then enter the name input screen and the cursor will be at the end of the name:

- The information is accurate. Press OK key.

- To correct the name, press key to delete characters.

- Enter the new name and press OK key.

4. You will then enter the number screen and the cursor will be at the end of the number :

- The information is accurate. Press OK.

- To correct the number, press to delete the numbers.

- Enter the new number and press OK.

Deleting a memory / the whole phonebook

1. Go to the menu " phonebook " / "delete " (or " delete all " to delete the entire phonebook list).

2. Select the entry you want to delete using  or . Press OK :

- If you do not wish to delete the entry, press .

- To delete the entry, press OK.

Assign a shortcut

This menu allows you to record two quick dial numbers assigned to the keys 1 and 2 on the keyboard.

1. Go to the menu " phonebook " / " directe mem. ".

2. Select the key you want to assign a number (1 or 2).

3. Press OK, " no number " is displayed on the screen.

4. Press MENU.

5. " edit number " appears on the screen.

6. Press OK.

7. Enter the name of the entry and press OK to confirm.

8. Enter the number of the entry. Press OK to confirm. You will hear a confirmation tone.

To call the number you have assigned to one of the shortcut keys, 1. Hold down the key on which the

number was programmed (1 or 2).

Inserting a pause (in dialling)

You can insert a pause in dialling a phone number if you want to wait before actually ringing.

While dialling the number you want to call, press and hold the key to insert the pause:

The display shows a ’’P’’.

SING THE MULTI

HANDSET CAPABILITIES

These functions are used for handset management when two or more handsets are registered on the

same base.

Intercom Call/Intercom

1. Make sure your handset is on standby mode.

2. Press the key on the handset.

- If your installation has two handsets, the second handset is directly called, and, "handset "

followed by the handset number are displayed on the screen.

- If your telephone installation has more than two handsets, the icon INT blinks on the screen and

the number of all registered handsets.

- Enter the desired handset number or press the key if you want to call all handsets.

D142

Answering an internal call

1. The ring melody from an internal call is different from an external call. " handset " and the calling

handset number appear on the screen. The "" is blinking.

2. Press the key to answer. The " " stop blinking.

3. Ending an internal call press .

Managing an external and an internal call

Transfering an external call to another handset registered on same base

1. During a call, press . The external user is put on hold.

2. Enter the internal call number. When the user answers, you can announce the call.

3. Press the key to transfer the call.

To switch from one call to another, press and hold down the key until an aural

signal is heard.

If the called handset does not answer, press to take back the call.

Making conference calls (3-way conversation)

You can connect one external call to two handsets registered at the base station. To set up a telephone

conference from an external call:

1. Press . key. The external user is put on hold.

2. Enter the internal call number. Wait until the internal user answers.

3. Press and hold key, until an aural signal is heard to start a three-way conference. "conference"

is displayed on the handset screen.

Two outside calls

Taking a second call while you are already on line

During a call, a beep is emitted by your operator to inform you that a second call is on hold. A screen

displays the number of this second caller on hold.

Press then the key to take back this new call.

Your first contact is put on hold and you can talk with the second caller.

Making a second call while you already on line

During a conversation, press then dial the number to be called.

The call in process is then put on hold and you can take the second call back.

Switching from one call to the other

To switch from one call to the other, press then the key .

The call in process is then put on hold.

Ending one of the two calls

To end one call and continue with the other, press then the key .

The call in process is then ended finally and you take the second call back.

To set up a 3-way conference (the 2 calls and yourself)

During a conversation, press then the key .

You can then talk with the 2 contacts at the same time.

To end the 3-way conference, press the red key .

D142

D142D142D142

USTOMISING THE HANDSET

Handset naming

The default name of the handset is "

handset N

" where

is the number of the registered handset.

1. Go to the menu " personal set " / " handset name ".

2. Use the keypad to enter the new name (up to 10 characters).

Use key to delete wrong input if necessary. Press OK.

Handset ringer level

1. Go to the menu " personal set " ". / " " / " handset tone ring volume

2. Use or  to select the volume level then press OK to confirm your selection.

Handset ringer melody

1. Go to the menu " personal set " / " " / " handset tone ring tones ".

Ten melodies are available: " melody 1 "… " melody 10 ".

2. Use or  to select the ring tone. Press OK.

Key tone On/Off

1. Go to the menu " personal set " / " handset tone " / " key beep ".

An information screen shows you the current state. Use or  to modify it.

2. Press OK key to confirm your selection.

Modifying the language

1. Go to the menu " personal set " / " language ".

2. Use or to choose the desired language. Press OK key to confirm your selection.

Auto talk

When active, the auto talk off feature enables you to automatically hang up as soon as you put the

handset on its base.

1. Go to the menu " personal set " / " auto hang-up ".

An information screen shows you the current state. Use  or  to modify it.

2. Press OK key to confirm your selection.

Key lock

1. Press and hold key for 1 second. An information screen shows you that the keys are locked.

2. To recover to normal, press and hold key 1 sec.

ETTING THE DATE AND TIME

Time and date

After a power cut the time has to be reset.

1. Go to the menu " clock & alarm " / " date/time". Current date is displayed.

- To keep the date, press OK.

- To change it, enter the new date in 20YY/MM/JJ format.

- To go back to change the entry .

D142D142D142

2. Press OK. Current time is displayed.

- To keep the time, press OK.

- To change it, enter the new time in the HH : MM ring the time, the time format. (If, after ente

format is 12H, use the  key to set aM and the  key to set pM).

- To go back to change the entry .

3. Press OK.

Hour format (12/24)

1. Go to the menu " clock & alarm " / " set format " / " time format ".

A screen displays the current format, use  or to change it.

2. Press OK.

Date format

1. Go to the menu " clock & alarm " ". / " set format " / " date format

A screen displays the current format, use  or  to change it.

2. Press OK.

Alarm clock

1. Go to the menu " clock & alarm " / " alarm ".

 To activate the alarm once, select "on once ".

 To repeat the alarm each day at the programmed time, select " on daily ".

 To deactivate the alarm, select "off ".

2. Select your choice then press OK.

Enter the time when you want the alarm to go off: "HH – mm ".

(If after entering the time, the time format 12H, use  key to set

aMaM

and the keyto set

pMpM

3. Press OK.

Modifying alarm tone

1. Go to the menu " ". clock & alarm " / " alarm tone

3 melodies are available: "melody 1", "melody 2" et "melody 3".

2. Select the desired melody, press OK key to confirm your selection.

You will hear a confirmation tone.

DVANCED SETTINGS

Base master PIN code

Your base station code (default setting 0000) is required to access certain security functions. This code

can include 8 digits.

1. Go to the menu " advanced set " / " change pin ".

2. Enter your old code first, press OK.

3. Enter your new PIN code.

Each time a digit is entered the «_»is replaced by a «*».

Press OK key to confirm your new PIN code. You will hear a confirmation tone.

Carefully note your base station code. You will need it to change certain settings.

D142D142D142

Association handset & base

1. Press and hold key for 5 seconds (after 1 minute if no Handset has started association process

the base goes back to standby).

2. Go to the menu " advanced set " / " registration ".

3. Enter the 4 digit base master PIN code (default 0000). Press OK.

4. Once the handset is registered. The handset automatically exits the registering mode.

5. The handset number assigned automatically by the base appears on the screen.

Disassociation of a handset

1. Go to the menu " advanced set " / " unregister ".

2. Enter the 4 digit base master PIN code (default 0000). Press OK.

3. Select the handset you want to delete using the  or  key then press OK (at standby state,

"pls reg h/s" is displayed on the screen.

Selecting the country

1. Go to the menu " advanced set " / " unregister ".

2. Enter the 4 digit base master PIN code (default 0000). Press OK.

3. Select the country where you are using the telephone. Press OK.

4. A confirmation screen appears, press OK.

Restoring the Handset / Base Default Settings

1. Go to the menu " advanced set " / " reset ".

2. A confirmation screen appears, press OK.

Prefix (Depending on Country)

If a PABX is used in a private network, you can program the outside call prefix.

This function sets:

-The PABX prefix number: this number will be added at the beginning of the number you dialled.

-The number to be detected: if the number you dialled starts with the recorded sequence, this

sequence will be automatically deleted.

These two settings are not applied if number you dialled starts with

"#", "*" or "P".

1. Go to the menu "advanced set " / "auto prefix ".

- Select "detect digit " to define the number giving you access to the outside line.

- Select "prefix" to specify the «digits before prefix».

2. Press OK.

Flash timing

If you connect your telephone to a private automatic branch exchange or use it in a foreign country, you

may need to modify the flash duration in order to use your telephone correctly with regard to the following

functionalities: outgoing 2nd call, incoming 2nd call, conference call.

Contact your administrator, who will supply the appropriate time period, and proceed to the new settings.

1. Go to the menu " advanced set " / " recall time ".

2. Select the appropriate time period, press OK.

Modifying the dialing mode

Most telephone systems use the tone dialling mode. You can, however, use the pulse dialling mode:

1. Go to the menu " advanced set " / " dial mode ".

2. Two modes are available: " tone " and " pulse ".

3. Press OK.

D142

First ring

When this function is activated, the receiver rings as soon as a call is received, without waiting for the

number to be displayed. If you have activated this function, it will be automatically deactivated when a call

is received with the number displayed (if you have this service).

1. Go to the menu " advanced set " / " first ring ".

2. Use the or keyto change the state.

3. Press OK.

ATTERIES SAFETY PRECAUTIONS

To avoid any risk of explosion:

 Make sure you have inserted the batteries correctly.

 Use only with 1,2V 400mAh type or equivalent rechargeable batteries pack.

 Do not dispose of the batteries in a fire. The cell may explode.

 Check with local code for possible special disposal instructions.

 Do not burn, disassemble, mutilate or puncture. Like other batteries of this type, toxic materials could be

released which can cause injury.

 To reduce the risk of fire or personal injury, use only the battery listed in the user’s guide.

 Keep batteries out of the reach of children.

 Remove batteries if storing over 30 days.

ENERAL PRODUCT CARE

To keep your telephone working and looking good, follow these guidelines:

 Avoid putting the phone near heating appliances and devices that generate electrical noise (for example,

motors or fluorescent lamps).

 DO NOT expose to direct sunlight or moisture.

 Avoid dropping and other rough treatment to the phone.

 Clean with a soft cloth.

 Retain the original packaging in case you need to ship the phone at a later date.

ROUBLESHOOTING

Causes of poor reception:

 Aluminium siding.

 Foil backing on insulation.

 Heating ducts and other metal construction can shield radio signals.

 You are too close to appliances such as microwaves, stoves, computers, etc).

 Atmospheric conditions, such as strong storms.

 Base installed in the basement or lower floor of the house.

 Base is plugged into an AC outlet with other electronic devices.

 Baby monitor is using the same frequency.

 Handset batteries is low.

 You are out of range of the base.

D142

Auto-diagnostics

Problem Solution

No display.

xMake sure the batteries are properly installed.

xPlace the handset on the base and fully charge the batteries.

xTo increase the life of your batteries, you can perform this operation about

every two months.

xIf these precautionary measures do not resolve this issue, replacement

batteries are available through your reseller.

xAs time goes by, you may notice a slight decrease in battery performance. Use

your handset until the battery is fully discharged, and then charge it for at least

15 hours.

Handset does

not ring.

xMake sure the RINGER setting on the handset is programmed to ON.

xYou may have too many extension phones on your line. Try unplugging some

phones.

You experience

static, noise or

fading in and

out.

xIs handset out of range?

Move closer to the base.

xDoes the base need to be relocated?

xCharge batteries.

xMake sure base is not plugged into an outlet with another household appliance.

Unit beeps

- Place handset in base for 20 seconds to reset the security code. If that doesn’t work, charge batteries for 15

hours.

- Clean charging contacts on handset and base with a soft cloth

- Replace batteries.

Memory dialling

- Did you program the memory location keys correctly?

- Did you follow proper dialling sequence?

- Make sure the tone/pulse setting is correct.

- Did you reprogram numbers into memory after power outage or batteries replacement?

NVIRONMENT

Preservation of the environment is an essential concern of SAGEMCOM. The desire of SAGEMCOM is to

operate systems observing the environment and consequently it has decided to integrate environmental

performances in the life cycle of its products, from manufacturing to commissioning, use and elimination.

Packaging

The presence of the logo (green dot) means that a contribution is paid to an approved

national organisation to improve packaging recovery and recycling infrastructures.

To facilitate recycling, please respect the sorting rules set up locally for this kind of waste.

Batteries

If your product contains batteries, they must be disposed of at appropriate collection

points.

D142

The product

The crossed-out waste bin stuck on the product or its accessories means that the product

belongs to the family of electrical and electronic equipments.

In this respect, the European regulations ask you to dispose of it selectively:

xAt sales points in the event of the purchase of similar equipment.

xAt the collection points made available to you locally (drop-off centre, selective

collection, etc.).

In this way you can participate in the re-use and upgrading of Electrical and Electronic Equipment Waste, which

can have an effect on the environment and human health.

ERMS AND

ONDITIONS FOR

NITED

INGDOM

& I

RELAND ONLY

In order to apply the guarantee, you should contact the SAGEMCOM Helpdesk or the retailer where you

purchased the equipment. Proof of purchase will be required in either case.

Please make sure that you use your equipment only for the purpose for which it was designed and under normal

usage conditions.

SAGEMCOM do not accept any liability for the equipment if used outside the frame of its original designed

purpose or any consequence that may arise from this usage.

Should any malfunction arise, the SAGEMCOM Helpdesk or your retailer will advise you how to proceed.

A) General Guarantee conditions

SAGEMCOM undertakes to remedy by repair or exchange at its own convenience, free of charge for labour and

replacement parts, any defects in the equipment during the guarantee period of 12 (twelve) months or 3 (three)

months for accessories, from the date of original invoice of the Equipment, where those defects are a result of

faulty workmanship.

Unless the customer has concluded with SAGEMCOM a maintenance contract in respect of the equipment which

specifically provides for repairs to be carried out at the customer's premises, the repairs will not be carried out on

the equipment at the customer premises.

The customer must however return the defective equipment at his/her own expense, to the address supplied by

the SAGEMCOM Helpdesk or by the retailer.

In the case that a product needs to be sent in for a repair, it must always be accompanied by a proof of purchase

(which is not altered, written on or in any way made illegible) showing that the product is still under guarantee. In

the case that no proof of purchase is enclosed, the SAGEMCOM repair centre will use the production date as its

reference for establishing the guarantee status of the product.

Apart from all legal obligatory rules, SAGEMCOM, do not give any Guarantee, either implicit or explicit which is

not set force in the present section, and can not be held responsible for any direct or indirect, material or

immaterial damage, either in or out of the frame of the present guarantee.

If any provision of this guarantee shall be held to be in whole or in part invalid or illegal due to an obligatory rule

applicable to consumers pursuant to their national legislation, such invalidity or illegality shall not impair or affect

the remaining provisions or parts of this guarantee.

This guarantee does not affect the Customer statutory rights.

B) Exclusions From Guarantee

SAGEMCOM shall have no liability under the guarantee in respect of:

x Damage, defects, breakdown or malfunction due to one or more of the following:

- Failure to properly follow the installation process and instructions for use

- An external cause to the equipment (including but not limited to: lightening, fire, shock, vandalism,

inappropriate conditions of electrical network or water damage of any nature)

- Modifications made without the written approval of SAGEMCOM

- Unsuitable operating conditions, particularly of temperature and humidity

- Repair or maintenance of the equipment by persons not authorised by SAGEMCOM

x Wear and tear from normal daily use of the equipment and its accessories

x Damage due to insufficient or bad packaging of equipment when returned to SAGEMCOM

x Usage of new versions of software without the previous approval of SAGEMCOM

x Work on any equipment or software modified or added without the prior written consent of SAGEMCOM

D142

x Malfunctions not resulting from the Equipment or from software installed in user workstations for the

purpose of use of the equipment

Communication problems related to an unsuitable environment including:

- Problems related to access and/or connection to the Internet such as interruptions by access networks or

malfunction of the line used by the subscriber or his correspondent

- Transmission faults (for example poor geographical coverage by radio and TV transmitters, interference

or poor line quality)

- Local network faults (wiring, servers, workstations) or the failure of the transmission network (such as but

not limited to interferences, fault or poor quality of the network

- Modification of the parameters of the cellular or broadcast network carried out after the sale of the

Product

x Normal servicing (as defined in the user guide supplied with the equipment) as well as malfunctioning due

to servicing not being carried out. Servicing costs are in any event always borne by the customer.

x Malfunctions resulting from the usage of products, consumables or accessories not compatible with the

equipment.

C) Out of Guarantee Repairs

In the cases set forth in B) as well as after expiry of the guarantee period, the customer must ask the Authorised

SAGEMCOM Repair Centre for a cost estimation prior to work being carried out.

In such cases, the repair and delivery costs will be invoiced to the customer.

The foregoing shall apply unless otherwise agreed in writing with the customer and only for the United Kingdom

and Ireland.

www.sagemcom.com

ERMS AND

ONDITIONS FOR OTHER COUNTRIES

If, despite our best efforts, your product presents any defects, you should refer to your retailer and present the

proof of purchase that they gave you on the day of purchase.

Should any malfunctioning arise, the retailer will advise you what to do.

For the warranty to apply, you should ensure that the product was used in accordance with the instructions for

use and the purpose for use, and that you have at your disposal the sales invoice or receipt stating the date of

purchase, the name of the retailer, the reference and the serial number of the product.

No coverage shall be given under this warranty if the following conditions are applicable:

x The required documents have been modified or altered in order to take advantage of the warranty.

x The manufacturing numbers, product brands or labels have been altered or made illegible.

x Interventions on the product have been made by an unauthorized person.

x The product has been subjected to abnormal or improper use.

x The product has been damaged by external factors such as lightning, over-voltage, moisture, accidental

damage, improper care as well as all Acts of God.

This present warranty does not affect the consumer rights that you may have under the laws in effect in your

country

Important:

Should you return the product to the after-sales department, please ensure that you return as well all the

elements and accessories originally supplied with the product.

x accidental damage, improper care as well as all Acts of God.

This present warranty does not affect the consumer rights that you may have under the laws in effect in your

country

253437152A

Produktspecifikationer

Varumärke:	Sagemcom
Kategori:	Telefon
Modell:	D142

Behöver du hjälp?

Om du behöver hjälp med Sagemcom D142 ställ en fråga nedan och andra användare kommer att svara dig

Ditt namn*

Din e-post*

Skriv din fråga här

Telefon Sagemcom Manualer

Sagemcom D780A Bruksanvisning

10 September 2024

Sagemcom D750 Bruksanvisning

10 September 2024

Sagemcom D142 Bruksanvisning

10 September 2024

Sagemcom D790A Bruksanvisning

10 September 2024

Sagemcom D77T Bruksanvisning

10 September 2024

Sagemcom D380 Bruksanvisning

10 September 2024

Sagemcom D530 Bruksanvisning

10 September 2024

Sagemcom C100 Bruksanvisning

10 September 2024

Sagemcom D530P Bruksanvisning

10 September 2024

Sagemcom D380A Bruksanvisning

10 September 2024

Telefon Manualer

Nyaste Telefon Manualer

Realme 6s Bruksanvisning

27 Oktober 2024

BT Freestyle 2010 Bruksanvisning

26 Oktober 2024

FlyingVoice IP622WP Bruksanvisning

26 Oktober 2024

Huawei Nova 9 Pro Bruksanvisning

24 Oktober 2024

Yealink MP56 Bruksanvisning

21 Oktober 2024

Profoon PDX-5900 Bruksanvisning

19 Oktober 2024

Gigaset A400A Bruksanvisning

18 Oktober 2024

Alcatel Smile Bruksanvisning

18 Oktober 2024

Belgacom Twist 555 duo Bruksanvisning

17 Oktober 2024

Emporia Select Basic Bruksanvisning

17 Oktober 2024