Sanus NFCD Bruksanvisning

Läs nedan 📖 manual på svenska för Sanus NFCD (5 sidor) i kategorin Inte kategoriserad. Denna guide var användbar för 5 personer och betygsatt med 4.5 stjärnor i genomsnitt av 2 användare

Sida 1/5
Assembly Instructions for Model: NFCD
Thank you for choosing a Sanus Systems Natural Media Tower. The Model
NFCD is designed to keep your collection clean and organized by storing up to
430 CDs or 230 DVDs, all in one convenient location.
If you do not understand these directions, please contact Sanus at 800.359.5520
or www.sanus.com. Check carefully to make sure that there are no missing or
defective parts. Our customer service representatives can quickly assist you
with assembly questions, and missing or damaged parts. Replacement parts
for products purchased through authorized dealers will be shipped directly to
you. Never use defective parts. Improper assembly may cause damage or
serious injury. Do not use this product for any purpose that is not explicitly
specied by Sanus Systems. Sanus Systems can not be liable for damage
or injury caused by incorrect assembly, or incorrect use. Please call Sanus
Systems before returning products to the point of purchase.
Required Tools: Rubber mallet or hammer, screwdrivers, phillips & regular
Supplied Parts List: (Not to Scale)
NFCD Top - A
Qty. 1
Glass Shelves - F
Qty. 14
NFCD Base - B
Qty. 1
Center Support - D
Qty. 1
Side Panels - E
Qty. 2
NFCD Foot - C
Qty. 4
Sanus Name Plate - G
Qty. 1
Sanus Systems 2221 Hwy 36 West, Saint Paul, MN 55113 02.28.06 (100028)
Customer Service: 800.359.5520. See complementary Sanus products at www.sanus.com
Supplied Hardware: (Full Size)
Step 1 - Attach Feet to NFCD Base
Insert a Machine Screw ( ) into each Foot ( ); then using the regular screwdriver, attach the Feet to the NFCD Base ( ). K C B
Diagram 1
Cam - H
Qty. 4
Cam Pin - I
Qty. 4
Plastic Dowel - J
Qty. 4
Wood Screw - L
Qty. 4
Machine Screw - K
Qty. 4
Shelf Pin - M
Qty. 56
B
K
C
C
C
C
K
K
K
Step 2 - Insert Cam Pins into Side Panels
There are two holes that are centered on each side of the Side Panels ( ), and 12” [304.3 mm] from each end. Using E
the phillips screwdriver, screw Cam Pins ( ) into the two holes of each Side Panel taking care not to over tighten the Cam I
Pins.
Diagram 2
E
I
E
Step 3 - Insert Cam into Center Support.
Place a Cam ( ) into each of the four holes in the Center Support ( )H D
NOTE: Each Cam has an arrow on it. Using a phillips screwdriver align each Cam so the arrow is pointing toward
the small hole on the edge of the Center Support (See Detail - A).
Diagram 3
Step 4 - Secure Side Panels to Center Support.
The Cam Pins ( ) installed in each Side Panel ( ) line up with the small holes in the edge of the Center Support ( ). The top I E F
of each Side Panel is smooth and the bottom has a notch routed in the inside edge.
Attach a Side Panel to each side of the Center Support and using a phillips screwdriver, rotate each Cam ( ) clockwise until H
tight (See Detail - B).
Diagram 4
D
Small Hole
Cam Hole
Cam - H
Small
Hole
Cam - H
Detail - A
Top
Smooth
Bottom
Notched
I
H
E
E
F
Detail -B

Produktspecifikationer

Varumärke: Sanus
Kategori: Inte kategoriserad
Modell: NFCD

Behöver du hjälp?

Om du behöver hjälp med Sanus NFCD ställ en fråga nedan och andra användare kommer att svara dig




Inte kategoriserad Sanus Manualer

Sanus

Sanus WSHSH1-W2 Bruksanvisning

26 September 2024
Sanus

Sanus BMF522 Bruksanvisning

24 September 2024
Sanus

Sanus BSF517 Bruksanvisning

24 September 2024
Sanus

Sanus SOA-SW106 Bruksanvisning

24 September 2024
Sanus

Sanus BLF528 Bruksanvisning

24 September 2024
Sanus

Sanus MFLF1 Bruksanvisning

21 September 2024
Sanus

Sanus MFSF1 Bruksanvisning

21 September 2024
Sanus

Sanus MFLD1 Bruksanvisning

21 September 2024
Sanus

Sanus MFIWP1 Bruksanvisning

21 September 2024

Inte kategoriserad Manualer

Nyaste Inte kategoriserad Manualer