Satel AXD-200 Bruksanvisning

Satel Luftfuktare AXD-200

Läs nedan 📖 manual på svenska för Satel AXD-200 (12 sidor) i kategorin Luftfuktare. Denna guide var användbar för 2 personer och betygsatt med 4.5 stjärnor i genomsnitt av 2 användare

Sida 1/12
AXD-200
Wireless multipurpose detector
Firmware version axd-20 03/ 1.00 0_en 21
SATEL sp. z o.o. ul. Budowlanych 66 - POLAND 80 298 Gdańsk •
tel. +48 58 320 94 00
www.satel.eu
IMPORTANT
The device should be installed by qualied personnel.
Prior to installation, please read carefully this manual.
Changes, modications or repairs not authorized by the manufacturer shall void your rights
under the warranty.
The rating plate of the device is located on the enclosure base.
SATEL aims to continually improve the quality of its products, which may result in changes in
their technical specications and software. Current information about the changes being
introduced is available on our website.
Please visit us at:
https://support.satel.eu
Hereby, SATEL sp. z o.o. declares that the radio equipment type AXD-200 is in
compliance with Directive 2014/53/EU. The full text of the EU declaration of conformity
is available at the following internet address: www.satel.eu/ce
In the EU, th radio equipment is only permitted to operate in the 868 MHz frequency is
band.
The following symbols may be used in this manual:
- note,
- caution.
The AXD-200 detector is designed for operation within the ABAX 2 / ABAX two-way wireless
system. It is a multipurpose device that can be used as magnetic contact, shock,
reorientation, temperature or ood detector. You should select the type of detector before
adding it to the system (see Selecting detector type). Table 1 shows how the detector is
identied in the wireless system, depending on the selected type.
Detector name in the system
Detector type
ABAX 2
ABAX
AMD- 200
AMD- 100
Magnetic contact
AMD- 201
AMD- 101
Dual channel magnetic contact
AMD- 202
AMD- 102
Magnetic contact with input for roller shutter
detector
AVD- 200
AVD- 100
Shock detector and magnetic contact
ARD- 200
ARD- 100
Reorientation detector
ATD-200
ATD-100
Temperature detector
AFD- 200
AFD- 100
Water ood detector
Table 1.
The detector with factory default settings is identied in the ABAX 2 system as AMD-200, and
in the ABAX system as AMD- 100.
This manual applies to the detector with rmware version 1.00, which is supported by:
ABAX 2:
ACU-220 / ACU-280 controller,
ARU-200 repeater.
ABAX:
ACU-120 / ACU-270 controller (rmware version 5.04 or newer),
ARU-100 repeater (rmware version 2.02 or newer),
INTEGRA 128-WRL control panel (rmware version 1.19 or newer and rmware
version of processor used to operate ABAX system 3.10 or newer).
The temperature detector (ATD-200) is not supported by the controller connected to
the VERSA / VERSA Plus / VERSA IP control panel.
1 Features
Possibility to select the type of detector before adding it to the system.
Encrypted two-way radio communication in the 868 MHz / MHz frequency band (AES 915
standard for the ABAX 2 system).
Transmission channel diversity 4 channels for automatic selection of the one that will
enable transmission without interference with other signals in the 868 MHz / MHz 915
frequency band (ABAX 2 system only).
Remote update of detector rmware (ABAX 2 system only).
Remote conguration.
Built-in temperature sensor (temperature measurement range from - 10°C to +55°C).

Produktspecifikationer

Varumärke: Satel
Kategori: Luftfuktare
Modell: AXD-200

Behöver du hjälp?

Om du behöver hjälp med Satel AXD-200 ställ en fråga nedan och andra användare kommer att svara dig




Luftfuktare Satel Manualer

Satel

Satel AXD-200 Bruksanvisning

7 September 2024

Luftfuktare Manualer

Nyaste Luftfuktare Manualer