Schertler STAT-C Bruksanvisning

Schertler mikrofon STAT-C

Läs nedan 📖 manual på svenska för Schertler STAT-C (2 sidor) i kategorin mikrofon. Denna guide var användbar för 2 personer och betygsatt med 4.5 stjärnor i genomsnitt av 2 användare

Ladda ner PDF
Sida 1/2
STAT Transducers
SCHERTLER SA
Via Beroldingen 18, CH-6850 Mendrisio,
Tel. 0041-91-630 07 10
www.schertler.com - info@schertler.com
Dear musician, recording engineer . . .
The SCHERTLER® system is used worldwide in recording and amplification situations whenever exceptional quality is a must. Many of the finest soloists and professional engi-
neers of our time have already chosen a SCHERTLER® device. The SCHERTLER® name guarantees performance, linearity and dynamics to the highest degree.
SCHERTLER® Transducers are developed and manufactured according to the utmost standards of quality engineering and workmanship. A lot of attention has been given to the
importance of long life, product endurance and performance by the selection of optimum materials and production processes. Nevertheless you should always handle your
Transducer with care.
Please do read carefully the directions for use to ensure proper operation. For further questions you are welcome to consult our representative in your country or ourselves here
in Switzerland; we then will try to help you by word and deed.
It is our hope and our goal to have improved the world of amplified sound of acoustic instruments and thus your individual instrument.
Yours faithfully,
Stephan Schertler and the SCHERTLER® AUDIO team
The pickup capsule is to be placed in the bridge with the cork upwards, almost vertically into the bridge hole under the G-string for the dou-
ble bass, under the A-string for the cello and under the E-string for the violin (Fig. 1).
Cut and sand the top of the cork until the capsule fits precisely into the hole, sanding the hole curvature on the cork to fit snugly and in
good contact with the wood. A sharp knife can be used carefully before sanding if a lot of the cork has to be cut off as a first step.
The pickup capsule should not be made to fit in too tightly. Too much pressure on the capsule can make the pickup lose its open sound and,
above all, can seriously damage the capsule!
The upper side of the cork has to be shaped closely to the shape of the bridge hole for the best results. Less than perfect results will be
obtained with the cork sanded too pointed or too flat, making the contact with the wood less than complete (Fig. 2).
After shaping, if the hole remains too small, particularly with the violin, the hole must be enlarged at the top to accomodate the transduc-
er, as some cork must remain (Fig. 3). In case of very small bridge holes, shortening of the bridge wings may be required (Fig. 4) to allow
the wedge to be fixed deeper and thus to create more space for the capsule.
Double bass: the cork should not be sanded of f to less than 6mm (1/4 in.).
It is possible that after some time of use, the cork may shrink a little and cause the capsule to no longer fit well. In this case we recom-
mend applying one or more layers of varnish on the top, i. e. the contact part of the cork, thus allowing the capsule to reacquire its prop-
er fitting without too much pressure on it. If need be, a little piece of paper can be jammed between cork and upper side of the bridge hole.
The connector will be fixed on the tailpiece as shown on (Fig. 5).
MOUNTING THE STAT TRANSDUCERS
U S E R ’ S M A N U A L
The electrostatic transducer is furnished with a preamplifier which needs a 9.0 VDC battery. The Preamp will be activated by inserting a
jack cable. Therefore, to prevent waste of battery, we recommend that you always remove the jack from the system when not in use.
However a distinguishing feature of the preamplifier is its minimal power consumption.
An alkaline battery of good quality will maintain the reqired operating voltage for about 300 hours.
To check the battery insert the jack in the OUTPUT; the check light will turn on; by inserting the INPUT jack the system is ready to work.
To change battery, remove the four screws from the housing-cover, remove the used battery and insert the new one, then replace the four
screws.
PREAMP

Produktspecifikationer

Varumärke: Schertler
Kategori: mikrofon
Modell: STAT-C

Behöver du hjälp?

Om du behöver hjälp med Schertler STAT-C ställ en fråga nedan och andra användare kommer att svara dig


mikrofon Schertler Manualer

Schertler

Schertler STAT-C Bruksanvisning

7 Januari 2025
Schertler

Schertler STAT-PRE Bruksanvisning

3 September 2024
Schertler

Schertler DYN-B P48 Bruksanvisning

2 September 2024

mikrofon Manualer

Nyaste mikrofon Manualer

HyperX

HyperX QuadCast S Bruksanvisning

8 Januari 2025
Monacor

Monacor ECM-306BU/SW Bruksanvisning

8 Januari 2025
Godox

Godox Cube-C Bruksanvisning

7 Januari 2025
Audibax

Audibax AWM 401 TD Bruksanvisning

6 Januari 2025
Audibax

Audibax Sidney 1250 A Bruksanvisning

6 Januari 2025
Vonyx

Vonyx WAT200 Bruksanvisning

6 Januari 2025
Audibax

Audibax AWM 201 Bruksanvisning

6 Januari 2025
Audibax

Audibax AWM 401 Bruksanvisning

6 Januari 2025
Audibax

Audibax AWM 403 Bruksanvisning

6 Januari 2025
Audibax

Audibax Sidney Conference 1000 Bruksanvisning

6 Januari 2025