Sharp XL-MP130 Bruksanvisning

Sharp CD-spelare/brännare XL-MP130

Läs nedan 📖 manual på svenska för Sharp XL-MP130 (42 sidor) i kategorin CD-spelare/brännare. Denna guide var användbar för 3 personer och betygsatt med 4.5 stjärnor i genomsnitt av 2 användare

Ladda ner PDF

Sida 1/42

Thank you for purchasing this SHARP product.

To obtain the best performance from this product, please read this

manual carefully. It will guide you in operating your SHARP product.

XL-MP130

MICRO COMPONENT SYSTEM XL-MP130 Micro Component System consisting of XL-MP130 (main unit)

and CP-MP130 (speaker system).

Accessories

Please confirm that the following accessories are included.

MODEL

OPERATION MANUAL

XL-MP130

Note:

Only the above accessories are included.

Remote control 1

(RRMCGA038AWSA)

AM loop antenna 1

(QANTL0005AWZZ)

FM antenna 1

(92LFANT1746A)

XL-MP130

Important Instruction

SPECIAL NOTES

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,

DO NOT REMOVE COVER (OR BACK).

NO USER-SERVICEABLE PARTS INSIDE. REFER SERVIC-

ING TO QUALIFIED SERVICE PERSONNEL.

Explanation of Graphical Symbols:

The lightning flash with arrowhead symbol,

within an equilateral triangle, is intended to

alert the user to the presence of uninsulated

“dangerous voltage” within the product’s en-

closure that may be of sufficient magnitude

to constitute a risk of electric shock to per-

sons.

The exclamation point within an equilateral

triangle is intended to alert the user to the

presence of important operating and main-

tenance (servicing) instructions in the lit-

erature accompanying the appliance.

0012

WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC

SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR

MOISTURE.

0012

Caution - use of controls or adjustments or performance

of procedures other than those specified herein may re-

sult in hazardous radiation exposure.

0012

NOTE

This equipment has been tested and found to comply with the limits for a

Class B digital device, pursuant to Part 15 of the FCC Rules. These

limits are designed to provide reasonable protection against harmful in-

terference in a residential installation. This equipment generates, uses,

and can radiate radio frequency energy and, if not installed and used in

accordance with the instructions, may cause harmful interference to ra-

dio communications. However, there is no guarantee that interference

will not occur in a particular installation. If this equipment does cause

harmful interference to radio or television reception, which can be deter-

mined by turning the equipment off and on, the user is encouraged to try

to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and receiver.

Connect the equipment into an outlet on a circuit different from that to

which the receiver is connected.

Consult the dealer or an experienced radio/TV technician for help.

WARNING

FCC Regulations state that any unauthorized changes or modifications

to this equipment not expressly approved by the manufacturer could void

the user's authority to operate this equipment.

NOTES

It is the intent of Sharp that this product be used in full compliance

with the copyright laws of the United States and that prior permission

be obtained from copyright owners whenever necessary.

Licensed under one or more of U.S. Pat. 4,972,484, 5,214,678,

5,323,396, 5,530,655, 5,539,829, 5,544,247, 5,606,618, 5,610,985,

5,740,317, 5,777,992, 5,878,080 or 5,960,037. 0303

FOR YOUR RECORDS

For your assistance in reporting this unit in case of loss or theft,

please record below the model number and serial number which

are located on the rear of the unit.

Please retain this information.

Model number .......................................................

Serial number .......................................................

Date of purchase .......................................................

Place of purchase .......................................................

0202

XL-MP130

Important Instruction

IMPORTANT SAFETY INSTRUCTIONS

Read Instructions - All the safety and operating instructions should

be read before the product is operated.

Retain Instructions - The safety and operating instructions should be

retained for future reference.

Heed Warnings - All warnings on the product and in the operating

instructions should be adhered to.

Follow Instructions - All operating and use instructions should be

followed.

Cleaning - Unplug this product from the wall outlet before cleaning.

Do not use liquid cleaners or aerosol cleaners. Use a damp cloth for

cleaning.

Attachments - Do not use attachments not recommended by the prod-

uct manufacturer as they may cause hazards.

Water and Moisture - Do not use this product near water - for ex-

ample, near a bath tub, wash bowl, kitchen sink, or laundry tub; in a

wet basement; or near a swimming pool; and the like.

Accessories - Do not place this product on an unstable cart, stand,

tripod, bracket, or table. The product may fall, causing serious injury to

a child or adult, and serious damage to the product. Use only with a

cart, stand, tripod, bracket, or table recommended by the manufac-

turer, or sold with the product. Any mounting of the product should

follow the manufacturer s instructions, and should use a mounting ac-

cessory recommended by the manufacturer.

A product and cart combination should be moved with

care. Quick stops, excessive force, and uneven surfaces

may cause the product and cart combination to over-

turn.

Ventilation - Slots and openings in the cabinet are provided for venti-

lation and to ensure reliable operation of the product and to protect it

from overheating, and these openings must not be blocked or cov-

ered. The openings should never be blocked by placing the product on

a bed, sofa, rug, or other similar surface. This product should not be

placed in a built-in installation such as a bookcase or rack unless proper

ventilation is provided or the manufacturer s instructions have been

adhered to.

11 Power Sources - This product should be operated only from the type

of power source indicated on the marking label. If you are not sure of

the type of power supply to your home, consult your product dealer or

local power company. For products intended to operate from battery

power, or other sources, refer to the operating instructions.

12 Grounding or Polarization - This product may be equipped with a

polarized alternating-current line plug (a plug having one blade wider

than the other). This plug will fit into the power outlet only one way.

This is a safety feature. If you are unable to insert the plug fully into the

outlet, try reversing the plug. If the plug should still fail to fit, contact

your electrician to replace your obsolete outlet. Do not defeat the safety

purpose of the polarized plug.

Alternate Warnings - This product is equipped with a three-wire

grounding-type plug, a plug having a third (grounding) pin. This plug

will only fit into a grounding-type power outlet. This is a safety feature.

If you are unable to insert the plug into the outlet, contact your electri-

cian to replace your obsolete outlet. Do not defeat the safety purpose

of the grounding-type plug.

13 Power-Cord Protection - Power-supply cords should be routed so

that they are not likely to be walked on or pinched by items placed

upon or against them.

Protective Attachment Plug - The product is equipped with an at-

tachment plug having overload protection. This is a safety feature. See

Instruction Manual for replacement or resetting of protective device. If

replacement of the plug is required, be sure the service technician has

used a replacement plug specified by the manufacturer that has the

same overload protection as the original plug.

XL-MP130

Important Instruction

IMPORTANT SAFETY INSTRUCTIONS (continued)

15 Outdoor Antenna Grounding - If an outside antenna or cable system

is connected to the product, be sure the antenna or cable system is

grounded so as to provide some protection against voltage surges and

built-up static charges. Article 810 of the National Electrical Code, ANSI/

NFPA 70, provides information with regard to proper grounding of the

mast and supporting structure, grounding of the lead-in wire to an an-

tenna discharge unit, size of grounding conductors, location of antenna

discharge unit, connection to grounding electrodes, and requirements

for the grounding electrode.

16 Lightning - For added protection for this product during a lightning

storm, or when it is left unattended and unused for long periods of

time, unplug it from the wall outlet and disconnect the antenna or cable

system. This will prevent damage to the product due to lightning and

power-line surges.

17 Power Lines - An outside antenna system should not be located in the

vicinity of overhead power lines or other electric light or power circuits,

or where it can fall into such power lines or circuits. When installing an

outside antenna system, extreme care should be taken to keep from

touching such power lines or circuits as contact with them might be

fatal.

Overloading - Do not overload wall outlets, extension cords, or integral

convenience receptacles as this can result in a risk of fire or electric shock.

19 Object and Liquid Entry - Never push objects of any kind into this

product through openings as they may touch dangerous voltage points

or short-out parts that could result in a fire or electric shock. Never spill

liquid of any kind on the product.

20 Servicing - Do not attempt to service this product yourself as opening

or removing covers may expose you to dangerous voltage or other

hazards. Refer all servicing to qualified service personnel.

21 Damage Requiring Service - Unplug this product from the wall outlet

and refer servicing to qualified service personnel under the following

conditions:

a) When the power-supply cord or plug is damaged,

b) If liquid has been spilled, or objects have fallen into the product,

c) If the product has been exposed to rain or water,

d) If the product does not operate normally by following the operating

instructions. Adjust only those controls that are covered by the op-

erating instructions as an improper adjustment of other controls may

result in damage and will often require extensive work by a qualified

technician to restore the product to its normal operation,

e) If the product has been dropped or damaged in any way, and

f) When the product exhibits a distinct change in performance - this

indicates a need for service.

22 Replacement Parts - When replacement parts are required, be sure

the service technician has used replacement parts specified by the

manufacturer or have the same characteristics as the original part.

Unauthorized substitutions may result in fire, electric shock, or other

hazards.

23 Safety Check - Upon completion of any service or repairs to this prod-

uct, ask the service technician to perform safety checks to determine

that the product is in proper operating condition.

24 Wall or Ceiling Mounting - The product should be mounted to a wall

or ceiling only as recommended by the manufacturer.

25 Heat - The product should be situated away from heat sources such

as radiators, heat registers, stoves, or other products (including ampli-

ANTENNA LEAD IN WIRE

P OWER SE RVICE GROUNDING

ELECTRODE SYSTEM

(NEC ART 250, PART H)

GROUNDING CONDUCTORS

(NEC SECTION 810-21)

GROUND CLAMPS

NEC - NATIONAL ELECTRICAL CODE

S2898A

ELEC TRIC

SE RVICE

EQUIPMENT

GROUND

CLAMP

Example of antenna grounding as per

National Electrical Code, ANSI/NFPA 70

ANTENNA DISCHARGE UNIT

(NEC SECTION 810-20)

fiers) that produce heat.

0304

XL-MP130

Important Instruction

Contents

Page

General Information

Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Controls and indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7 - 9

Preparation for Use

System connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10 - 12

Remote control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Basic Operation

General control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Setting the clock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

CD or MP3/WMA disc Playback

Listening to a CD or MP3/WMA disc . . . . . . . . . . . . . . . . .16 - 18

Advanced CD or MP3/WMA disc playback . . . . . . . . . . . .19 - 21

MP3/WMA navigation (only for MP3/WMA ﬁles) . . . . . . . .22 - 25

Radio

Listening to the radio . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26 - 27

Tape Playback

Listening to a cassette tape . . . . . . . . . . . . . . . . . . . . . . . .28 - 29

Tape Recording

Recording on a cassette tape . . . . . . . . . . . . . . . . . . . . . . .29 - 31

Advanced Features

Timer and sleep operation . . . . . . . . . . . . . . . . . . . . . . . . .32 - 35

Enhancing your system . . . . . . . . . . . . . . . . . . . . . . . . . . .36 - 37

References

Troubleshooting chart . . . . . . . . . . . . . . . . . . . . . . . . . . . . .37 - 39

Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40

Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41

CONSUMER LIMITED WARRANTY . . . . . . . . . . . . . .Back cover

ENERGY STAR® Program Information

0312

Products that have earned

the ENERGY STAR® are

designed to protect the

environment through

superior energy efficiency.

To comply with the ENERGY STAR® standards mentioned above,

please cancel the demonstration mode, as described on page .

ENERGY STAR® is a U.S. registered mark.

XL-MP130

General Information

Precautions

General

Please ensure that the equipment is positioned in a well-ventilated

area and ensure that there is at least 4" (10 cm) of free space

along the sides, top and back of the equipment.

Do not place anything on top of the unit.

Do not expose the unit to moisture, to temperatures higher than

140˚F (60˚C) or to extremely low temperatures.

If your system does not work properly, disconnect the AC power

cord from the AC outlet. Plug the AC power cord back in, and then

turn on your system.

This unit should only be used within the range of 41

˚F - 95˚F (5˚C

- 35˚C).

Warning:

The voltage used must be the same as that specified on this unit. Us-

ing this product with a higher voltage other than that which is speci-

fied is dangerous and may result in a fire or other type of accident

causing damage. SHARP will not be held responsible for any dam-

age resulting from use of this unit with a voltage other than that which

is specified.

Volume control

The sound level at a given volume setting depends on speaker effi-

ciency, location and various other factors. It is advisable to avoid ex-

posure to high volume levels, which occurs while turning the unit on

with the volume control setting up high, or while continually listening

at high volumes.

Use the unit on a firm, level surface free from

vibration.

Keep the unit away from direct sunlight,

strong magnetic fields, excessive dust,

humidity and electronic/electrical equip-

ment (home computers, facsimiles, etc.)

which generate electrical noise.

In case of an electrical storm, unplug the

unit for safety.

MICRO COMPONENT SYSTEM

XL-MP130

POWER/

4" (10 cm)4" (10 cm) 4" (10 cm)

4" (10 cm)

Hold the AC power plug by the head when

removing it from the AC outlet, as pulling

the cord can damage internal wires.

Do not remove the outer cover, as this

may result in electric shock. Refer inter-

nal service to your local SHARP service

facility.

XL-MP130

General Information

Controls and indicators

Front panel

Reference page

1. Disc Trays . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

2. Timer Indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33

3. Power On/Stand-by Button . . . . . . . . . . . . . . . . . . . . . . . . . 14

4. Clock/Timer Button . . . . . . . . . . . . . . . . . . . . . . . . . 15, 32, 35

5. Tape Record Pause Button . . . . . . . . . . . . . . . . . . . . . . 30, 31

6. Cassette Compartment . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

7. Headphone Jack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36

8. Disc Tray Open/Close Button . . . . . . . . . . . . . . . . . . . . . . . 16

9. Disc Number Select Buttons . . . . . . . . . . . . . . . . . . . . . . . . 16

10. Disc Direct Play Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

11. Remote Sensor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

12. Volume Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

13. Memory/Set Button . . . . . . . . . . . . . . . . 15, 21, 25, 27, 32, 35

14. Equalizer Mode Select Button . . . . . . . . . . . . . . . . . . . . . . 14

15. Extra Bass/Demo Mode Button . . . . . . . . . . . . . . . . . . 12, 14

16. CD Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

17. Tape Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

18. Disc Track Down or Fast Reverse, Tape Rewind,

Tuner Preset Down, Time Down Button . . . . . . 15, 18, 27, 29

19. Disc Track Up or Fast Forward, Tape Fast Forward,

Tuner Preset Up, Time Up Button . . . . . . . . . . . 15, 18, 27, 29

20. Tuner (Band) Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

21.

Video/Auxiliary Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36

22. Disc Play or Repeat, Tape Play Button . . . . . . . . . 16, 20, 28

23. Tuning Down Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

24. Tuning Up Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

25. Disc or Tape Stop Button . . . . . . . . . . . . . . . . . . . . . . . 18, 29

XL-MP130

General Information

Controls and indicators (continued)

Display Reference page

1. Disc Number Indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

2. MP3/WMA Folder Indicator . . . . . . . . . . . . . . . . . . . . . . . . . 22

3. MP3/WMA Title Indicators . . . . . . . . . . . . . . . . . . . . . . . . . . 22

4. MP3 Indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

5. WMA Indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

6. Sleep Indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35

7. Timer Play Indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33

8. Timer Recording Indicator . . . . . . . . . . . . . . . . . . . . . . . . . . 33

9. Tape Record Indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30

10. MP3/WMA Total Indicator . . . . . . . . . . . . . . . . . . . . . . . . . . 23

11. Daily Timer Indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33

12. FM Stereo Mode Indicator . . . . . . . . . . . . . . . . . . . . . . . . . . 26

13. FM Stereo Receiving Indicator . . . . . . . . . . . . . . . . . . . . . . 26

14. Tape Play Indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

15. Memory Indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21, 25

16. Extra Bass Indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

17. Disc Repeat Play Indicator . . . . . . . . . . . . . . . . . . . . . . . . . 20

18. Disc Pause Indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

19. Disc Play Indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

Rear panel Reference page

1. Speaker Terminals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

2. AC Power Cord . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

3. FM 75 Ohms Antenna Terminal . . . . . . . . . . . . . . . . . . . . . . 11

4. FM Antenna Ground Terminal . . . . . . . . . . . . . . . . . . . . . . . 11

5. AM Loop Antenna Jack . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

6. Video/Auxiliary (Audio Signal) Input Jacks . . . . . . . . . . . . 36

7. Cooling Fan . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

8. Subwoofer Pre-output Jack . . . . . . . . . . . . . . . . . . . . . . . . . 37

Speaker system

1 2 3 4 5 6 7 8 9

11 12 13

10 14

16 17

18 19

RATED SPEAKER IMPEDANCE:

6 OHMS MIN.

AC INPUT

ANTENNA

RIGHT

RIGHT LEFT

GND

75 OHMS

LOOP

VIDEO/AUX

SUBWOO FER

PRE-O UT

SPEAKERS

LEFT 8

1. Tweeter

2. Woofer

3. Bass Reflex Duct

4. Speaker Wire

XL-MP130

General Information

Remote control

Reference page

1. Remote Control Transmitter . . . . . . . . . . . . . . . . . . . . . . . . 13

2. Disc Number Select Buttons . . . . . . . . . . . . . . . . . . . . . . . . 16

3. Cursor Buttons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

4. Character Input/Disc Direct Search Buttons . . . . . . . . 19, 24

5. Equalizer Mode Select Button . . . . . . . . . . . . . . . . . . . . . . 14

6. Extra Bass Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

7. Power On/Stand-by Button . . . . . . . . . . . . . . . . . . . . . . . . . 14

8. CD Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

9. Tuner (Band) Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

10. Tape Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

11. Video/Auxiliary Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36

12. Volume Up and Down Buttons . . . . . . . . . . . . . . . . . . . . . . 14

13. Disc Clear/Dimmer Button . . . . . . . . . . . . . . . . . . . . . . 14, 21

14. Disc Random Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

15. Disc Stop Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

16. Tape Stop Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

17. Memory Button . . . . . . . . . . . . . . . . . . . . 15, 21, 25, 27, 32, 35

18. Disc Pause Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

19. Disc Play or Repeat Button . . . . . . . . . . . . . . . . . . . . . . 16, 20

20. Tape Play Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

21. Tape Record Pause Button . . . . . . . . . . . . . . . . . . . . . . 30, 31

22. MP3/WMA Navigation Mode Select Button . . . . . . . . . . . . 23

23. MP3/WMA Display Button . . . . . . . . . . . . . . . . . . . . . . . . . . 18

24. Enter Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

25. Clock/Timer Button . . . . . . . . . . . . . . . . . . . . . . . . . 15, 32, 35

26. Character Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

27. Disc Track Down or Fast Reverse, Tape Rewind,

Tuner Preset Down, Time Down Button . . . . . . 15, 18, 27, 29

28. Disc Track Up or Fast Forward, Tape Fast Forward,

Tuner Preset Up, Time Up Button . . . . . . . . . . . 15, 18, 27, 29

25 26 27 28

14 18

22 23 24

C D

XL-MP130

Preparation for Use

System connections

RATED SPEAKER IMPEDANCE:

6 OHMS MIN.

AC INPUT

ANTENNA

RIGHT

RIGHT LEFT

GND

75 OHMS

LOOP

VIDEO/AUX

SUBWOOFER

PRE-OUT

SPEAKERS

LEFT

Left speaker

Right speaker

AC outlet

(AC 120 V, 60 Hz)

Speaker connection (see page 11)

AM loop antenna

FM antenna

Make sure to unplug the AC power cord before any connections.

Antenna connection (see page 11)

AC power connection (see page 12)

XL-MP130

∂ Preparation for Use

Antenna connection

Supplied FM antenna:

Connect the FM antenna wire to the FM 75 OHMS terminal and po-

sition the FM antenna wire in the direction where the strongest signal

can be received.

Supplied AM loop antenna:

Connect the AM loop antenna to the AM LOOP jack. Position the AM

loop antenna for optimum reception. Place the AM loop antenna on

a shelf, etc., or attach it to a stand or a wall with screws (not sup-

plied).

Note:

Placing the antenna on the unit or near the AC power cord may

cause noise pickup. Place the antenna away from the unit for better

reception.

Installing the AM loop antenna:

Speaker connection

Connect the black wire to the minus (-) terminal, and the red wire to

the plus (+) terminal.

Caution:

Speaker grilles are removable

< Assembling > < Attaching to the wall >

Wall Screws (not supplied)

RATED SPEAKER IMPEDANCE:

6 OHMS MIN.

AC INPUT

ANTENN A

RIGHT

RIGHT LEFT

GND

75 OHMS

LOOP

VIDEO/AUX

SUBWOOFER

PRE-OUT

SP EAKERS

LEFT

Use speakers with an impedance of 6 ohms or more, as lower im-

pedance speakers can damage the unit.

Do not mistake the right and the left chan-

nels. The right speaker is the one on the right

side when you face the unit.

Do not let the bare speaker wires touch

each other.

Do not allow any objects to fall into or to be

placed in the bass reflex ducts.

Do not stand or sit on the speakers. You may

be injured.

Incorrect

Make sure nothing comes into contact

with the speaker diaphragm when you

remove the speaker grilles.

RATED SPEAKER IMPEDANCE:

6 OHMS MIN.

AC INPUT

ANTENNA

RIGHT

RIGHT LEFT

GND

75 OHMS

LOOP

VIDEO/AUX

SUBWOOFER

PRE-OUT

SPEAKERS

LEFT

BlackRed

XL-MP130

Preparation for Use

System connections (continued)

AC power connection

After checking all the connections have been made correctly, plug

the AC power cord of this unit into the AC outlet. If you plug in the unit

first, the unit will enter the demonstration mode.

Notes:

The unit will start the tape initialization when plugged in to the AC

outlet. During this process, an initializing sound will be heard and

the unit cannot be turned on. Wait until the process is finished.

Unplug the AC power cord from the AC outlet if the unit will not be

in use for a prolonged period of time.

Demonstration mode

Outdoor FM antenna

Use an outdoor FM antenna if you require better reception.

Consult your dealer.

Note:

When an outdoor FM antenna is used, disconnect the supplied FM

antenna wire.

Cooling fan:

The main unit is built with a cooling fan at the rear of the unit for im-

proved cooling. Please do not cover the opening of the fan with any

obstacles, as this will block proper ventilation.

RATED S PEAKER IMP EDANCE:

6 OHMS MI N.

AC INPUT

ANTENNA

RIGHT

RIG HT LEFT

GND

75 OHMS

LOOP

VIDEO/AUX

SUBWOOFER

PRE-OUT

SPEAKERS

LEFT

AC outlet

(AC 120 V, 60 Hz)

RATED SPEAKER IMPEDANCE:

6 OHMS MIN.

AC INPUT

RIGHT

RIGHT LEFT

VIDEO/AUX

SUB WOOFER

PRE- OUT

SPEAKERS

LEFT

The first time the unit is plugged in, the

unit will enter the demonstration mode.

You will see words scroll.

To cancel the demonstration mode:

When the unit is in the power stand-

by mode (demonstration mode),

press the X-BASS/DEMO button.

The unit will enter the low power

consumption mode.

To return to the demonstration mode:

When the unit is in the power stand-by mode, press the X-BASS/

DEMO button again.

Note:

When the power is on, the X-BASS/DEMO button can be used to se-

lect the extra bass mode.

Outdoor

FM antenna

75 ohms

coaxial cable

XL-MP130

Preparation for Use

Remote control

Battery installation

Precautions for battery use:

Replace all old batteries with new ones at the same time.

Do not mix old and new batteries.

Remove the batteries if the unit will not be used for long periods

of time. This will prevent potential damage due to battery leakage.

Caution:

Do not use rechargeable batteries (nickel-cadmium battery, etc.).

Installing the batteries incorrectly may cause the unit to malfunc-

tion.

Battery removal:

Open the battery cover and pull up the battery to take out.

Notes concerning use:

Replace the batteries if the operating distance is reduced or if the

operation becomes erratic.

Periodically clean the transmitter on the remote control and the

sensor on the unit with a soft cloth.

Exposing the sensor on the unit to strong light may interfere with

operation. Change the lighting or the direction of the unit if this

occurs.

Keep the remote control away from moisture, heat, shock, and vi-

brations.

Test of the remote control

Check the remote control after checking all the connections (see

pages 10 - 12).

Point the remote control directly at the remote sensor on the unit.

The remote control can be used within the range shown below:

Press the ON/STAND-BY button. Does the power turn on? Now, you

can enjoy music.

Use 2 "AA" size batteries (UM/SUM-3, R6, HP-7 or similar).

Batteries are not included.

1 Open the battery cover.

2 Insert the batteries according to the direction indicated in

the battery compartment (back of the battery cover).

When inserting or removing the batteries, push them toward the

battery terminals.

3 Close the cover.

XL-MP130

Basic Operation

General control

To turn the power on

Press the ON/STAND-BY button to turn the power on.

To change the display brightness

You can switch the display brightness by pressing the CLEAR/

DIMMER button more than 2 seconds.

Volume auto fade-in

If you turn off and on the main unit with the volume set to 27 or

higher, the volume starts at 16 and fades in to the last set level.

Volume control

Main unit operation:

When the VOLUME control is turned clockwise, the volume will

increase. When it is turned counterclockwise, the volume will

decrease.

Remote control operation:

Press the VOLUME (+ or -) button to increase or decrease the volume.

Bass control

When the power is ﬁrst turned on, the unit will enter the extra bass

mode which emphasizes the bass frequencies, and "X-BASS" will

appear. To cancel the extra bass mode, press the X-BASS/DEMO

(X-BASS) button.

Equalizer

When the EQUALIZER (EQUALIZER MODE) button is pressed, the

current mode setting will be displayed. To change to a different

mode, press the EQUALIZER (EQUALIZER MODE) button repeat-

edly until the desired sound mode appears.

After use:

Press the ON/STAND-BY button to enter the power stand-by mode.

30 MAXIMUM0 .....

ROCK For rock music.

FLAT No equalization.

CLASSIC For classical music.

POPS For pop music.

JAZZ For jazz.

VOCAL Vocals are enhanced.

XL-MP130

CD or MP3/WMA disc Playback

Listening to a CD or MP3/WMA disc

This system can play back a standard CD, CD-R/RW in the CD format

and CD-R/RW with MP3 or WMA ﬁles, but cannot record on them.

Some audio CD-R and CD-RW discs may not be playable due to the

state of the disc or the device that was used for recording.

MP3:

MP3 is a form of compression. It is an acronym which stands

for MPEG Audio Layer 3.

MP3 is a type of audio code which is processed by signiﬁcant

compression from the original audio source with very little loss

in sound quality.

This system supports MPEG 1 Layer 3, MPEG 2 Layer 3, and

VBR files.

During VBR ﬁle playback, time counter in the display may differ

from its actual playback time.

WMA:

WMA ﬁles are Advanced System Format ﬁles that include audio

ﬁles which are compressed with Windows Media Audio codec.

WMA is developed by Microsoft as an audio format ﬁle for Win-

dows Media Player.

"MP3" or "WMA" indicator will light up after the unit reads infor-

mation on an MP3 or WMA disc.

Auto power on function:

When you press any of the following buttons, the unit turns on.

CD button (main unit and remote control): The unit turns on and

the "CD" function is activated.

CD / button on the remote control: The unit turns on and CD

playback starts (regardless of the last function).

 / button on the main unit: The unit turns on and playback of

the last function starts (CD,TAPE,TUNER,VIDEO/AUX).

Auto power off function:

In the stop mode of CD, MP3 or WMA operation, the main unit enters

the stand-by mode after 15 minutes of inactivity.

XL-MP130

CD or MP3/WMA disc Playback

Playback will begin from track 1 on DISC 1. After that disc ﬁn-

ishes playing, the next disc will automatically play.

After the last track on the ﬁfth disc is played, the unit will stop

automatically.

When there is no disc in one of the disc trays (1 - 5), the empty

tray will be skipped to the next tray with a disc.

To exchange other discs while playing a disc:

Press one of the 1 - 5 buttons for the stopped disc and within 5

seconds, press the OPEN/CLOSE button and exchange discs.

To remove the discs:

In the stop mode, press the 1 - 5 button and within 5 seconds,

press the OPEN/CLOSE button.

Caution:

Do not place two discs in one disc tray.

Do not play discs of special shapes (heart, octagon, etc). It may

cause malfunctions.

Do not push the disc tray while it is moving.

If the power fails while the tray is open, wait until the power is re-

stored.

If the disc tray is stopped with force, "ER-CD20" will appear on the

display for 3 seconds and the unit will not function. If this occurs,

press the ON/STAND-BY button to enter the power stand-by

mode and then turn the power on again.

If TV or radio interference occurs during CD operation, move the

unit away from the TV or radio.

If a disc is damaged, dirty, or loaded upside down, the disc will be

skip or not play.

1Press the ON/STAND-BY button to turn the power on.

2Press the CD button.

3Press the 1 button and within 5 seconds, press the

OPEN/CLOSE button to open the disc tray 1.

4Place the disc on the disc tray 1, label side up.

Be sure to place 3" (8 cm) disc in the middle of the disc trays.

5Press the OPEN/CLOSE button to close the disc tray 1.

Due to the structure of the disc information, it takes longer to

read an MP3/WMA disc than a normal CD (approximately 20

to 90 seconds).

6You can place discs on the trays 2 - 5 by following steps

3 - 5.

7Press the / button to start playback.

5" (12 cm) 3" (8 cm)

[CD]

Total number of

tracks on the disc

Total playing

time of the disc

Total number

of folders

Total number

of files

MP3 indicator

[MP3/WMA] WMA indicator

Disc play indicator

XL-MP130

CD or MP3/WMA disc Playback

Listening to a CD or MP3/WMA disc (continued)

Various disc functions Notes for CD:

Notes for MP3/WMA discs:

Track up/track down is possible only within individual discs.

The sound is heard during fast forward/fast reverse with a CD, but

not with an MP3/WMA disc. For fast forward or fast reverse of an

MP3/WMA disc, refer to playback time on the display.

Fast forward/fast reverse is possible only within individual tracks.

When the end of the track is reached during fast forward, the next

track will be played. Playback of the track will begin when its be-

ginning is reached during fast reverse.

To change the display (MP3/WMA discs only)

Function Main unit Remote

control

Operation

Play Press in the stop

mode.

Stop Press in the playback

mode.

Pause Press in the playback

mode. Press the /

button to resume play-

back from the paused

point.

Track up/

Track down

Press in the playback

or stop mode.

If you press the button

in the stop mode,

press the / button

to start the desired

track.

Fast for-

ward/Fast

reverse

Press and hold down

in the playback mode.

Release the button to

resume playback.

Track up/track down is possible only within individual discs.

Fast forward/fast reverse is possible only within individual discs.

When the end of the last track is reached during fast forward,

"END" will appear on the display and CD operation will be paused.

When the beginning of the first track is reached during fast

reverse, the unit will enter the playback mode.

While a disc is playing, press the DISPLAY

button.

Each time the button is pressed, the display

will change as follows.

Folder name

File name

Track number Elapsed

playback time

XL-MP130

CD or MP3/WMA disc Playback

Advanced CD or MP3/WMA disc playback

To specify a disc to play

You can play a disc by specifying the disc number.

Playback will begin from track 1 on the chosen disc.

After the last track on the chosen disc is played, the unit stops

automatically.

Note:

If a disc tray with no disc is selected, playback will not start and the

disc indicator will go out.

To stop playback:

Press the (CD ) button.

Direct track search

By using the direct search buttons, the desired tracks on the current

disc can be played.

If the direct search buttons are pressed while the disc is stopped,

press the / button to start the desired track on the current disc.

Notes:

A track number higher than the number of tracks on the disc can-

not be selected.

During random play, direct search is not possible.

1Press one of the 1 - 5 buttons to select the desired disc.

Selected disc number

2Within 5 seconds, press the CD DIRECT PLAY button on

the main unit.

Use the direct search buttons on

the remote control to select the de-

sired track while playing the se-

lected disc.

Selected track number

The direct search buttons allow you to select up to number 9.

When selecting number 10 or higher, use the "+10" button.

A. For example, to choose 13

1 Press the "+10" button once.

2 Press the "3" button.

B. For example, to choose 30

1 Press the "+10" button three times.

2 Press the "0" button.

XL-MP130

CD or MP3/WMA disc Playback

Advanced CD or MP3/WMA disc playback (continued)

Repeat play

Repeat play can play all 5 discs, all tracks on a chosen disc, or a

programmed sequence continuously.

To cancel repeat play:

Press the / button again.

" " will go out.

To cancel repeat play:

Press the CD DIRECT PLAY button again.

" " will go out.

Random play

The tracks on the disc(s) can be played in random order automatically.

To cancel random play:

Press the / button.

"R" will go out.

To cancel random play:

Press the CD DIRECT PLAY button.

"R" will go out.

Notes:

If you press the button during random play, you can move to

the track selected next by the random operation. On the other

hand, the button does not allow you to move to the previous

track. The beginning of the track being played will be located.

In random play, the unit will select and play tracks automatically.

(You cannot select the order of the tracks.)

Caution:

After performing repeat or random play, be sure to press the (CD

) button. Otherwise, the disc(s) will play continuously.

To repeat all tracks on up to 5 discs:

Press the / button twice.

To repeat desired tracks:

Perform steps 1 - 6 in "Programmed play" section on page 21 and

then press the / button twice.

To repeat all tracks on the chosen disc:

1 Press one of the 1 - 5 buttons.

2 Within 5 seconds, press the CD DIRECT

PLAY button twice.

To random play all tracks on up to 5 discs:

Press the RANDOM button on the remote control.

To random play all tracks on the chosen disc:

1 Press one of the 1 - 5 buttons.

2 Within 5 seconds, press the CD DI-

RECT PLAY button.

3 Press the RANDOM button on the re-

mote control.

XL-MP130

CD or MP3/WMA disc Playback

Programmed play

You can choose up to 32 selections for playback in the order you like.

To cancel the programmed play mode:

While in the stop mode and the "MEMORY" indicator is lit, press the

CLEAR/DIMMER button on the remote control. The "MEMORY" in-

dicator will disappear and all the programmed contents will be

cleared.

Adding tracks to the program:

If a program has been previously stored, the "MEMORY" indicator

will be displayed. Then follow steps 1 - 6 to add tracks. The new

tracks will be stored after the last track of the original program.

To check which tracks are programmed:

While the unit is stopped in the programmed play mode, press the

or button.

Notes:

When a disc with programmed tracks is ejected, the program is

automatically canceled.

Even if you press the ON/STAND-BY button to enter the stand-by

mode or change the function from CD to another, the programmed

selections will not be cleared.

During the program operation, random play is not possible.

During programmed play, the CD DIRECT PLAY button will not

work.

1While in the stop mode, press the

MEMORY/SET (MEMORY) button

to enter the programming save

mode.

2Press one of the 1 - 5 buttons

to select the desired disc.

Selected disc number

3Press the direct search buttons

on the remote control to select

the desired track.

Selected track number

You can also select a track by pressing the or button.

4Press the MEMORY/SET (MEMO-

RY) button to save the track

number.

5Repeat steps 2 - 4 for other tracks. Up to 32 tracks can be

programmed.

If you make a mistake, the programmed tracks can be cleared

by pressing the CLEAR/DIMMER button.

6Press the (CD ) button.

The total number in memory will ap-

pear.

7Press the / button to start playback.

To clear the programmed selections:

Press the CLEAR/DIMMER button on the re-

mote control while the "MEMORY" indicator

is flashing.

Each time the button is pressed, one track will

be cleared, beginning with the last track pro-

grammed.

XL-MP130

CD or MP3/WMA disc Playback

MP3/WMA navigation (only for MP3/WMA ﬁles)

MP3/WMA navigation:

You can search and play ﬁles by folder or title. For example, when

you assign three titles to a ﬁle, enter genre (such as jazz) as title 1,

album name as title 2, and music title as title 3 to search the ﬁle by

any title.

You can search and play ﬁles by folder or title 1/2/3 within one

MP3/WMA disc (see page 23).

By entering a name, you can search ﬁles by folder or title 1/2/3

within one MP3/WMA disc (see page 24).

Folders or titles can be programmed within one MP3/WMA disc

(see page 25).

When you enter ﬁle names on your PC, connect words with

hyphens. This product recognizes the ﬁrst word as title 1, second

one as title 2, and third one as title 3. Up to three words can be rec-

ognized.

Notes:

MP3 ﬁles must have the extension ".mp3".

WMA ﬁles must have the extension ".wma".

Up to 100 folders or 300 files can be read on the unit. If either limit

is exceeded, no more folders/files are displayed.

This unit recognizes and displays up to 48 characters for folder

names, and up to 32 characters for title 1/2/3.

All ﬁle/folder names appear in uppercase.

Example:

(File name)

(POPULAR-HITS 1-A MUSIC.mp3)

AAA

(POPULAR-HITS 2-B MUSIC.mp3)

(JAZZ-HITS 1-A MUSIC.mp3)

BBB

(JAZZ-HITS 2-B MUSIC.mp3)

(ROCK-HITS 1-A MUSIC.mp3)

CCC

(ROCK-HITS 2-B MUSIC.mp3)

(ROCK-HITS 3-C MUSIC.mp3)

(ROCK-HITS 4-D MUSIC.mp3)

Folder

Title 1 Title 2 Title 3

Folder Title 1

Title 2 Title 3

XL-MP130

CD or MP3/WMA disc Playback

File search (by folder or title 1/2/3)

You can search and play ﬁles by folder or title 1/2/3 within one MP3/

WMA disc.

File search by title 1/2/3:

In step 5, select "T-1", "T-2" or "T-3" and follow the same steps as

ﬁle search by folder.

The unit searches all ﬁles on the disc, regardless of the folder.

To stop playback:

Press the CD button.

To exit the MP3/WMA navigation mode:

In the stop mode, press the CD button.

Notes:

In the MP3/WMA navigation mode, direct play and direct search

functions are disabled.

If a folder, title or ﬁle name does not appear, or appears incor-

rectly, remove and reinsert the disc and try again.

If you press the RANDOM button in the stop mode, the MP3/

WMA navigation mode will be canceled.

1Press one of the 1 - 5 buttons to select a disc tray con-

taining an MP3/WMA disc.

2Press the / button, and the unit starts to read the MP3/

WMA disc.

3Press the CD button to stop playback.

"NAVI READ" appears and the display shows the total number

of folders and files on the selected disc.

4Press the NAVIGATION button.

5Press the , , or cursor but-

ton on the remote control to select

"FOL", "T-1", "T-2" or "T-3". To

search files by folder name, select

"FOL" (will flash).

The following steps describe file search by folder:

6Press the ENTER button.

The total number of folders (or titles) appears for 2 seconds,

and names of the first 2 folders (or titles) are displayed.



The NAVIGATION button allows you to go one step back.

Press the DISPLAY button to

check the number of files.

Total number

of folders

Total number

of files

MP3 indicator

WMA indicator

Folder Title 1

Title 2 Title 3

Folder name

7Use the or cursor button to scroll and select a folder

(or title), and then press the ENTER button.

If you press the / cursor button instead of the ENTER but-

ton, all files in the selected folder (or title) are played.

8Use the or cursor button to scroll and select a file.

9Press the / button to start playback.

The unit plays from the selected file to the last file in the select-

ed folder (or title), and the previous display returns.

Folder name

File name

XL-MP130

CD or MP3/WMA disc Playback

MP3/WMA navigation (only for MP3/WMA ﬁles) (continued)

Character search (for folder or title 1/2/3)

By entering a name, you can search ﬁles by folder or title 1/2/3

within one MP3/WMA disc.

To exit the MP3/WMA navigation mode:

In the stop mode, press the CD button.

Notes:

The unit searches regardless of the case, and names found will

appear in uppercase.

Some symbols do not appear properly.

Character entry with direct buttons:

For example, press "2" four times to enter "C".

1Perform steps 1 - 3 in "File search (by folder or title 1/2/3)"

on page 23.

2Press the NAVIGATION button.

3Press the , , or cursor

button on the remote control to

select "FOL", "T-1", "T-2" or "T-3".

To search files by folder name,

select "FOL" (will flash).

4Press the CHARACTER button for 2 seconds.

The display will be ready for editing characters.

1st row: String table

2nd row: Input editor (8 digits)

5Press the or cursor button to select the desired alpha-

bet.

Press the or button to go to the next page of character

display.

6Press the CHARACTER button and the active character will

be entered in the 2nd row of the display.

To delete an entered character, move the cursor to the charac-

ter with the or button and press the CLEAR/DIMMER but-

ton on the remote control.

7Repeat steps 5 and 6 to enter characters.

In the folder (or title) name search, you do not have to enter the

full name. The unit searches for names beginning with the en-

tered characters.

Folder Title 1

Title 2 Title 3

8When finished, press the ENTER button. The unit searches

for the same name within folders (or titles).

If the search word is not in the folder (or title) name, "NOT

FOUND" appears and the menu returns.

9Use the or cursor button to scroll and select a folder

(or title).

10Press the / button to start playback.

All files in the selected folder (or title) are played, and the previ-

ous display returns.

The direct buttons on the remote

control can also be used for charac-

ter entry.

In step 5 on the left, use buttons 0 -

9 to enter alphabets.

Alphabet types change as you

press a button.

2 A B C

1 2 ABC 3 DEF 4 GHI 5 JKL 6 MNO

7 PQRS

8 TUV

9 WXYZ

: indicates a space.

Characters:

XL-MP130

CD or MP3/WMA disc Playback

Programmed play (for folder, title 1/2/3)

Folders or titles can be programmed within one MP3/WMA disc.

Folder, title 1, title 2 and title 3 cannot be programmed together

simultaneously.

To stop playback:

Press the CD button.

The programmed contents are not cleared.

To check, add or delete programmed contents:

In the stop mode, select a folder (or title) with the or cursor

button. If the folder (or title) is programmed, "MEMORY" ﬂashes.

When you press the MEMORY button with "MEMORY" ﬂashing,

the folder (or title) is removed from the program.

If you press the MEMORY button with "MEMORY" off, the folder

(or title) is added to the program.

To clear all programs, press the CLEAR/DIMMER button in the

stop mode.

To exit the MP3/WMA navigation mode:

In the stop mode, press the CD button.

The programmed contents are cleared.

Notes:

The programmed contents are cleared when you eject a disc,

play another disc, switch the function, or enter the stand-by mode

with the ON/STAND-BY button.

During programmed play, the CD DIRECT PLAY button on the

main unit will not work.

If you press the RANDOM button in the stop mode, the MP3/

WMA navigation mode will be canceled.

If tracks are programmed using track numbers (see "Pro-

grammed play" on page 21):

In the MP3/WMA navigation mode, only programs by folder (or title)

name are played. When you exit the mode, the programs by folder

(or title) name are cleared.

When you exit the MP3/WMA navigation mode, programs by track

number are canceled.

(Programs by track number are cleared when you remove the disc.)

1Perform steps 1 - 3 in "File search (by folder or title 1/2/3)"

on page 23.

2Press the NAVIGATION button.

3Press the , , or cursor button on the remote control

to select "FOL", "T-1", "T-2" or "T-3" and then press the

ENTER button.

The total number of folders (or titles) appears for 2 seconds,

and names of the first 2 folders (or titles) are displayed.

4Press the or cursor button to select the desired folder

(or title) and then press the MEMORY button.

The folder (or title) is memorized with all the files.

5Repeat step 4 for other folders (or titles).

Up to 10 folders (or 10 titles) can be programmed.

6Press the / button to start playback.

Programmed play will always start from the smallest folder (or

title) number.

Produktspecifikationer

Varumärke:	Sharp
Kategori:	CD-spelare/brännare
Modell:	XL-MP130

Behöver du hjälp?

Om du behöver hjälp med Sharp XL-MP130 ställ en fråga nedan och andra användare kommer att svara dig

Ditt namn*

Din e-post*

Skriv din fråga här

CD-spelare/brännare Sharp Manualer

Sharp CD-G10000 Bruksanvisning

1 September 2024

Sharp XL-MP131 Bruksanvisning

27 Augusti 2024

Sharp XL-UH1H Bruksanvisning

20 Augusti 2024

Sharp CD-SW200 Bruksanvisning

19 Augusti 2024

Sharp XL-MP130 Bruksanvisning

17 Augusti 2024

Sharp GX-M10HOR Bruksanvisning

27 Juli 2024

CD-spelare/brännare Manualer

Nyaste CD-spelare/brännare Manualer

Phonocar VM550 Bruksanvisning

5 April 2025

Proscan PRCD1025 Bruksanvisning

10 Mars 2025

Proscan PCD300-BLACK Bruksanvisning

5 Mars 2025

Atoll CD100 Bruksanvisning

20 Februari 2025

Atoll CD200 Bruksanvisning

20 Februari 2025

AVM CD 30.3 Bruksanvisning

20 Februari 2025

AVM Evolution CD 3.2 MKII Bruksanvisning

20 Februari 2025

Atoll CD50 Bruksanvisning

20 Februari 2025

Atoll DR100 Bruksanvisning

20 Februari 2025

Gold Note CD-1000 MK II Bruksanvisning

20 Februari 2025