Shure SM81 Bruksanvisning

Shure mikrofon SM81

Läs nedan 📖 manual på svenska för Shure SM81 (20 sidor) i kategorin mikrofon. Denna guide var användbar för 6 personer och betygsatt med 4.5 stjärnor i genomsnitt av 2 användare

Ladda ner PDF
Sida 1/20
MODEL SM81
UNIDIRECTIONAL CONDENSER MICROPHONE
The Shure Model SM81 is a high-quality, unidirectional
condenser microphone designed for studio recording, broad-
casting, and sound reinforcement. Its wide frequency re-
sponse, low noise characteristics, and low RF susceptibility
have made it a standard for applications involving acoustic in-
struments, especially guitar, piano, and cymbals.
The SM81 is ruggedly constructed. It operates on phantom
power and performs over a wide range of temperatures and hu-
midity conditions. It is furnished with a swivel adapter, attenua-
tor-switch lock, foam windscreen, and case for carrying and
storage. Other accessories are available.
Model SM81 Features
•20 Hz to 20 kHz frequency response
•Flat response curve for accurate reproduction of sound
sources
•Low noise and high output clipping level
•Low distortion over a wide range of load impedances
•Cardioid polar pattern, uniform with frequency and symme-
tric about axis, providing maximum rejection and minimum
coloration of off-axis sounds
•Low RF susceptibility
•Selectable low-frequency response: flat, 6 or 18 dB/octave
rolloff
•0 dB/10 dB lockable attenuator switch
•Phantom powering (DIN 45 596 voltages of 12 to 48 Vdc)
•Rugged steel construction for durability
•Field-usable over wide range of temperature and humidity
conditions
SPECIFICATIONS
Type
Condenser (electret bias)
Frequency Response
20 to 20,000 Hz (see Figure 1)
20 200001000 10000
50 100
98765432 98765432
+10
0
–10
Hz
dB
1 METER
TYPICAL FREQUENCY RESPONSE
FIGURE 1
Polar Pattern
Cardioid (unidirectional) response—uniform with
frequency, symmetrical about axis (see Figure 2)
150o
120o
150o
120o
180o
30o
60o
90o
30o
60o
90o
–5 dB
–10 dB
–15 dB
–20 dB
0
500 kHz
100 Hz
1 kHz
150o
120o
150o
120o
180
o
30o
60 o
90o
30 o
60o
90o
–5 dB
–10 dB
–15 dB
–20 dB
0
2 kHz
5 kHz
10 kHz
TYPICAL POLAR PATTERNS
FIGURE 2
Output Impedance
Rated at 150 Ω (85 Ω actual)
Recommended minimum load impedance: 800 Ω (May
be used with loads as low as 150 Ω with reduced clip-
ping level)
Output Configuration and Connector
Balanced, transformer-coupled output; male XLR con-
nector
Sensitivity (at 1,000 Hz)
Open Circuit Voltage –45 dBV/Pascal (5.6 mV). . . . . . . (1 Pascal = 94 dB SPL)
Clipping Level (at 1,000 Hz)
800 Ω Load –4 dBV (0.63 V). . . . . . . . . . . . . . . . . . . . . . .
150 Ω Load –15 dBV (0.18 V). . . . . . . . . . . . . . . . . . . . . .
Total Harmonic Distortion
Less than 0.5% (131 dB SPL at 250 Hz into 800 Ω load)
Model SM81 User Guide
27B2916 (BJ)
E2002, Shure Incorporated Printed in U.S.A.
2
Maximum SPL (at 1,000 Hz)
800 Ω load 136 dB (attenuator at 0). . . . . . . . . . . . . . . .
146 dB (attenuator at –10)
150 Ω load 128 dB (attenuator at 0). . . . . . . . . . . . . . . .
138 dB (attenuator at –10)
Hum Pickup
–3 dB equivalent SPL in a 1 mOe field (60 Hz)
Self-Noise (equivalent sound pressure levels; measured
with true rms voltmeter)
16 dB typical, A-weighted
19 dB typical, weighted per DIN 45 405
Signal-to-Noise Ratio
78 dB (IEC 651)* at 94 dB SPL
*S/N ratio is difference between microphone output at 94 dB SPL
and microphone self-noise A-weighted.
Overvoltage and Reverse Polarity Protection
Max. external voltage applied to pins 2 and 3 with
respect to pin 1 + 52 Vdc. . . . . . . . . . . . . . . . . . . . . .
Reverse polarity protection 200 mA max.. . . . . . . . . . . .
(diode-clamped)
Polarity
Positive pressure on diaphragm produces positive volt-
age on pin 2 relative to pin 3
Cartridge Capacitance
54 pF
Low Frequency Response Switch Positions
Flat; –6 dB/octave below 100 Hz; –18 dB/octave below
80 Hz
Attenuator Switch Positions (Lockable)
0 or –10 dB
Power
Supply Voltage 11 to 52 Vdc, positive, pins 2 and 3. .
Current Drain 1.2 mA max.. . . . . . . . . . . . . . . . . . . . . . . .
Environmental Conditions
Temperature:
Storage – 29_ to 74_ C. . . . . . . . . . . . . . . . . . . . . . .
( 20–_ to 165_ F)
Operating – 6.7_ to 49_ C. . . . . . . . . . . . . . . . . . . . . .
(20_ to 120_ F)
Humidity:
Storage 0–95% relative humidity at room. . . . . . . .
temperature (72_ _to 80 F, 22_ to 27_ C)
Case
Steel construction with vinyl metallic paint finish and
stainless steel screens
Dimensions
See Figure 3
Weight
Net 230 grams (8 oz). . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Packaged 740 grams (1 lb 10 oz). . . . . . . . . . . . . . . . . .
Certification
Eligible to bear CE marking. Conforms to European
EMC Directive 89/336/EEC. Meets applicable tests and
performance criteria in European EMC Standard EN
55103 (1996) parts 1 and 2 for residential (E1) and light
industrial (E2) environments.
OPERATION
Power
The SM81 requires phantom power. This may be supplied
to the microphone by a mixer, preamplifier or console with built-
in phantom power or from an external power supply (such as
the Shure model PS1A). Phantom power sources providing be-
tween 11 and 52 Vdc are suitable.
Use only high-quality cables because intermittent shorts
between broken shield wires and balanced conductors will
cause extremely large noise transients in the system. Avoid
ground loops due to grounded connector shells or the micro-
phone case touching other grounded metal objects. Follow
generally accepted audio grounding practices.
Impedance
A minimum load impedance of 800 Ω or greater should be
used for maximum signal handling and minimum distortion. The
load may be as low as 150 Ω, but a reduction in output clipping
level will result. It should be noted that the power supply itself
may add loading (3300 Ω in the Shure PS1A power supply) to
the microphones.
PS1A Power Supply
When using the Shure PS1A to phantom power the SM81,
connect the microphone cable to the SM81 and to the MICRO-
PHONE connector of the power supply. The power supply uses
the balanced audio cable pair to carry the supply current to the
microphone and the cable shield as a ground return.
Connect the OUTPUT connector of the power supply to a
low-impedance microphone input of a mixer, audio console or
tape recorder. A second SM81 may be connected to the re-
maining power supply channel in a similar manner.
212 mm
20 mm
23.5 mm
OVERALL DIMENSIONS
FIGURE 3
3
Low-Frequency Response Filter
The SM81 has a three-position low-frequency response fil-
ter controlled by a switch located on its handle. The switch is
recessed to avoid accidental movement, but may be easily
moved with fingertips. The user may select either flat response,
low-frequency rolloff of 6 dB per octave below 100 Hz, or low-
frequency cutoff of 18 dB per octave below 80 Hz (see
Figure 1). When close-miking instruments or vocalists, an
increase in low-frequency response (proximity effect) takes
place. Figure 4 illustrates this effect with the switch in each of
the three positions. Note that the low-frequency response filter
may be used to compensate for proximity effect or reduce low-
frequency noise from stage traffic and other sources.
20 100050 100
+10
0
–10
Hz
dB
152.4 MM ( )
152.4 MM ( )
152.4 MM ( )
PROXIMITY EFFECT AND COMPENSATION
FIGURE 4
Attenuator Switch
The SM81 has a switchable 10 dB capacitive attenuator to
prevent high sound pressure levels from overloading its internal
electronics. The attenuator is engaged by rotating the actuator
ring, located directly below the grille assembly, until it reaches
the “– ”10 position. This reduces the output of the microphone
by 10 dB and increases the maximum sound pressure level at
clipping by 10 dB. There are no intermediate levels of attenua-
tion available.
The attenuator ring may be locked in either the “ ”0 or 10“– ”
position as follows. Unscrew the grille and cartridge assembly
by unscrewing counter-clockwise from the top. Turn the actua-
tor ring to the “ ”0 or 10 position as desired. Insert the actuator“– ”
ring lock (small clear piece of plastic) in the area behind the ac-
tuator ring between the pin and the edge of the slot. This will
prevent the ring from turning. Replace the grill and cartridge as-
sembly.
Mixer Overload
The SM81’s output is about 15 dB higher than most dynam-
ic microphones. At moderate to high SPLs, this additional out-
put may require attenuation (or padding). If no attenuation is
available on the preamplifier, mixer or console being used, a re-
sistive attenuator can be inserted between the microphone and
the input. The Shure Model A15AS Attenuator (15, 20, or 25 dB
switch-selectable) is specially designed for use with condenser
microphones such as the SM81. Alternately, the attenuator de-
sign shown in Figure 5 may be used. The resistors shown are
1/2-watt, 1% tolerance, and the circuit may be packaged in a
Switchcraft S3FM adapter housing. The circuit will provide15
dB of attenuation and can be used between the SM81 and the
PS1A (or other power supply), or between the PS1A and the
mixer. Two of these circuits may be used in series to provide 30
dB of attenuation. (Note that, due to excessive loading, com-
mercially available 150 Ω attenuators, such as the Shure Model
A15AS, are not recommended when two are used in series.)
12
3
OUTPUT TO
MIXER
INPUT FROM
MICROPHONE
12 3
412
412
215
15 DB ATTENUATOR CIRCUIT
FIGURE 5
Wind Noise
The wide frequency response of the SM81 makes it sensi-
tive to wind, breath, and air currents from heating, ventilation
and cooling (HVAC) systems. The foam windscreen included
with the SM81 can be used to reduce wind and breath noise,
while the low-frequency response filter can be used to reduce
low-frequency room noise caused by HVAC systems.
The Model A81G Pop Filter Grille attenuates breath pop-
ping sounds when the microphone is close-talked, and permits
its use outdoors with minimal pickup of rushing and rumbling
sounds. To install the A81G, slip it over the SM81 until the inside
of the A81G touches the top of the microphone. Tighten the
A81G by rotating the knurled collar clockwise from the bottom.
(Note: When removing the A81G, first loosen the knurled collar.
Otherwise the cartridge will unscrew with the A81G.)
For outdoor use under very windy conditions, use the Mod-
el A81WS large foam windscreen.
CAPACITOR
CARTRIDGE
FET
IMPEDANCE
CONVERTER
LF
RESPONSE
FILTER
CLASS A
COMPOUND
AMPLIFIER
RFI
FILTER
BALANCED
TRANSFORMER
REGULATOR/
REVERSE
VOLTAGE
PROTECT
CAPACITIVE
ATTENUATOR
BLOCK DIAGRAM
FIGURE 6

Produktspecifikationer

Varumärke: Shure
Kategori: mikrofon
Modell: SM81

Behöver du hjälp?

Om du behöver hjälp med Shure SM81 ställ en fråga nedan och andra användare kommer att svara dig


mikrofon Shure Manualer

Shure

Shure VP89M Bruksanvisning

30 December 2025
Shure

Shure PGA DRUMKIT4 Bruksanvisning

30 December 2025
Shure

Shure PGA DRUMKIT6 Bruksanvisning

30 December 2025
Shure

Shure Microflex MX395 Bruksanvisning

30 December 2025
Shure

Shure KSM11 Bruksanvisning

30 December 2025
Shure

Shure MoveMic Bruksanvisning

30 December 2025
Shure

Shure SBC210LM Bruksanvisning

26 Oktober 2024
Shure

Shure MXA901-R Bruksanvisning

25 September 2024
Shure

Shure SBC-DC-903 Bruksanvisning

23 September 2024
Shure

Shure AXT910 Bruksanvisning

22 September 2024

mikrofon Manualer

Nyaste mikrofon Manualer

MXL

MXL Forge Bruksanvisning

22 Mars 2025
Austrian Audio

Austrian Audio OC16 Bruksanvisning

19 Mars 2025
Kenwood

Kenwood KMC-66 Bruksanvisning

18 Mars 2025
Kenwood

Kenwood KMC-70 Bruksanvisning

18 Mars 2025
Kenwood

Kenwood KMC-32 Bruksanvisning

18 Mars 2025
Comica

Comica Vimo C2 Bruksanvisning

12 Mars 2025
Louroe Electronics

Louroe Electronics Verifact B Bruksanvisning

10 Mars 2025
Louroe Electronics

Louroe Electronics Verifact C Bruksanvisning

10 Mars 2025
Louroe Electronics

Louroe Electronics Verifact K Bruksanvisning

10 Mars 2025
Louroe Electronics

Louroe Electronics C-ML Bruksanvisning

10 Mars 2025