Shure WCM16 Bruksanvisning

Shure mikrofon WCM16

Läs nedan 📖 manual på svenska för Shure WCM16 (6 sidor) i kategorin mikrofon. Denna guide var användbar för 2 personer och betygsatt med 4.5 stjärnor i genomsnitt av 2 användare

Ladda ner PDF
Sida 1/6
1/6
WCM16 -- Headset Condenser Microphone
General Description
The Shure Model WCM16 head-worn electret condenser microphone is intended for wireless use by performers,
lecturers, and others who require the highest quality voice pickup with maximum mobility. Its wide frequency re
sponse, low RF susceptibility and reliable operation at temperature and humidity extremes make the WCM16 suit
able for virtually any vocal application. When used with the Shure Body-Pack Transmitters, the performance of the
WCM16 closely resembles the finest conventional vocal microphones.
Miniaturized active circuitry included in the cartridge assembly provides equalization that tailors the low-frequency
response to resemble the warm proximity effect of larger vocal microphones. Because of this low-end response, it
is not necessary to position the microphone directly in front of the mouth, thus avoiding much popping and breath
noise, even without the supplied foam pop screen.
The microphone's hypercardioid unidirectional pickup pattern provides maximum isolation from ambient noise and
from adjacent sound sources such as musical instruments, loudspeakers and other performers. This permits high
er gain-before-feedback without loss or masking of vocals.
FEATURES:
•Extra lightweight, adjustable headband stays secure and virtually disappears while being worn
•Response comparable to the finest conventional vocal microphones
• Hypercardioid polar pattern provides maximum isolation from vocalist's own instrument and those of other per
formers
•Uniform polar pattern at all frequencies for maximum gain before feedback
•High input clipping level eliminates overload distortion
•Supplied acoustic foam pop screen
•Reliable at temperature and humidity extremes
Wearing the Microphone Headset
1. Place the microphone on the user's head so that the large diameter band is horizontal across the back of the
head. The band may be completely hidden under the hair. The ends of the headband should fit comfortably in
front of the ears. Extend or retract the adjustable headband (see Figure 1) to achieve this result.
2. For maximum gain before feedback, carefully extend or retract the boom (see Figure 1) so that the microphone
grille (silver side) is within 40 mm (1-1/2 in.) of the left corner of the mouth. It may be necessary to bend the
Shure Incorporated
2/6
headband tube just in front of the left ear for optimum microphone positioning. A slight bend downward and/ or
away is usually sufficient.
Note: The headband tubing will not withstand repeated bending, so make this adjustment only once, if neces
sary.
3. If breath noise or popping is audible, install the supplied pop screen so that the red dot on the pop screen cor
responds to the location of the microphone grille.
Figure 1: PARTS OF THE WCM16 HEAD-WORN MICROPHONE
Positioning the Microphone Pickup
The hypercardioid unidirectional pickup pattern of the WCM16 has maximum rejection of unwanted sound sources
at about a 110° angle each way from the front axis of the microphone (see Figure 1). Directly to the rear of the mi
crophone (at 180°) there is as little as 6dB rejection-not much less pickup than at the front of the microphone (at
0°).
Sound sources that may cause feedback (such as monitor or P.A. speakers) or sound that you do not want to pick
up with the WCM16 (such as percussion instruments or other performers) should NOT be placed directly to the
rear of the microphone. It is better to adjust positioning so that unwanted sound sources are located at the 110°
maximum rejection points. Note that when wearing the headset the rear of the microphone points out towards the
wearer's left.
Shure Incorporated
3/6
Connecting to a Transmitter
The WCM16 is configured for direct connection to a Shure Body-Pack Transmitter, such as models T1, T1G, T11,
SC1, EC1, or LX1, using the attached cable.
Microphone Powering
The WCM16 is designed to be powered from the +5 Vdc source at microphone connector pin 2 of a Shure trans
mitter.
Specifications
(Measured using test circuit in Figure 4)
Type
Condenser (electret bias)
Frequency Response
50 to 18,000 Hz
Polar Pattern
Hypercardioid, uniform with frequency
Output Level (close-talked at 1,000 Hz)
Open Circuit Voltage -55.0 (1.8 at 0.6 ) 1 Pascal=94 dB SPL dBV mV m
Maximum Sound Pressure Level
150 at 1%THD dB
Dynamic Range
121 dB
Output Noise
29 equivalent SPL, A-weighted dB

Produktspecifikationer

Varumärke: Shure
Kategori: mikrofon
Modell: WCM16

Behöver du hjälp?

Om du behöver hjälp med Shure WCM16 ställ en fråga nedan och andra användare kommer att svara dig


mikrofon Shure Manualer

Shure

Shure VP89M Bruksanvisning

30 December 2025
Shure

Shure PGA DRUMKIT4 Bruksanvisning

30 December 2025
Shure

Shure PGA DRUMKIT6 Bruksanvisning

30 December 2025
Shure

Shure Microflex MX395 Bruksanvisning

30 December 2025
Shure

Shure KSM11 Bruksanvisning

30 December 2025
Shure

Shure MoveMic Bruksanvisning

30 December 2025
Shure

Shure SBC210LM Bruksanvisning

26 Oktober 2024
Shure

Shure MXA901-R Bruksanvisning

25 September 2024
Shure

Shure SBC-DC-903 Bruksanvisning

23 September 2024
Shure

Shure AXT910 Bruksanvisning

22 September 2024

mikrofon Manualer

Nyaste mikrofon Manualer

MXL

MXL Forge Bruksanvisning

22 Mars 2025
Austrian Audio

Austrian Audio OC16 Bruksanvisning

19 Mars 2025
Kenwood

Kenwood KMC-66 Bruksanvisning

18 Mars 2025
Kenwood

Kenwood KMC-70 Bruksanvisning

18 Mars 2025
Kenwood

Kenwood KMC-32 Bruksanvisning

18 Mars 2025
Comica

Comica Vimo C2 Bruksanvisning

12 Mars 2025
Louroe Electronics

Louroe Electronics Verifact B Bruksanvisning

10 Mars 2025
Louroe Electronics

Louroe Electronics Verifact C Bruksanvisning

10 Mars 2025
Louroe Electronics

Louroe Electronics Verifact K Bruksanvisning

10 Mars 2025
Louroe Electronics

Louroe Electronics C-ML Bruksanvisning

10 Mars 2025