SiriusXM SXVRBT1 Bruksanvisning

SiriusXM Radio SXVRBT1

Läs nedan 📖 manual på svenska för SiriusXM SXVRBT1 (80 sidor) i kategorin Radio. Denna guide var användbar för 11 personer och betygsatt med 4.5 stjärnor i genomsnitt av 2 användare

Ladda ner PDF

Sida 1/80

QUICK START GUIDE

Scan here

for activation

offers

CAUTION: Do not attempt to install, activate, or adjust any of the

setting options described in this Quick Start Guide unless your

vehicle is parked in a safe location.

Magnetic Mount

Antenna

Antenna & Dash Mount

Alcohol Preparation Pads

Aux Audio Cable

Dash Mount

Vent Mount and

Extended Vent Clamps

Roady BT Display

12 3 4 5 6 7 8 9 0

Magnetic Adapter Extra Adhesive

What’s in the Box?

Display Cable

Intelligent Power Adapter

Dash Mount Method:

IMPORTANT: The air temperature needs to be at least 60°F to install the Dash Mount. If needed, turn on the

heater in your vehicle.

A. Select a flat surface for the Dash Mount with ample room for the Roady BT display. Avoid

mounting on leather surfaces. Choose a location that doesn’t interfere with the driver’s vision or

access to driving controls, one that won’t interfere with the deployment of airbags or other safety

equipment, and makes the Roady BT display easily accessible for operation. (Airbag locations are

typically marked with “SRS” logos.)

B. Orient the adhesive foot so that Roady BT is easily accessible. Loosen the knob and adjust the

adhesive foot to position , , or , and then tighten it.1 2 3

C. You can tilt the Dash Mount in your preferred direction.

D. Remove the adhesive liner from the back of the Magnet

and adhere the adhesive side of the Magnet to the Dash

Mount.

E. Clean the mounting surface in the vehicle with the alcohol

preparation pad and let it dry thoroughly.

F. Once the surface is dry, remove the adhesive liner from the Dash

Mount. Press and hold the Dash Mount in place for 30 seconds.

Allow the adhesive to cure for 2-4 hours.

G. Attach the Roady BT Display to the magnet on the Dash Mount.

Vent Mount Method:

A. Select a vent with ample room for the Roady BT display, one that won’t interfere with the deployment

of airbags or other safety equipment, and makes the Roady BT display easily accessible for operation.

(Airbag locations are typically marked with “SRS” logos.)

B. Some vents have recessed louvers. If yours are recessed, remove the regular vent clamps and

install the extended vent clamps.

C. Remove the adhesive liner from the back of the Magnet

and adhere the adhesive side of the Magnet to the Vent

Mount.

D. Install the Vent Mount onto the vehicle vent.

i. Insert the vent mount into the vent opening.

ii. Push until hooked on the rear of the vent louver. Rest the foot against the bottom of the vent.

iii. If necessary, adjust the tilt of the Vent Mount by repositioning the foot to a different tilt

adjustment hole.

E. Attach the Roady BT Display to the magnet on the Vent Mount.

Find a Location for the Roady BT Display and Mount it

Select either the t method or the Dash Moun Vent Mount method for mounting the Roady BT, or, if there is a metal surface in the vehicle, the Magnet can be attached directly to the metal surface without using the

Dash or Vent Mount. Other magnetic type mounts may also be purchased separately from other vendors.

Start Here

PUSH

I II III

DashDashDash

Vent

Louver

Vent Vent

HOOKED

TILT

ADJUSTMENT

HOLES