Smart-AVI SM-EDPN-2Q Bruksanvisning

Smart-AVI Växla SM-EDPN-2Q

Läs nedan 📖 manual på svenska för Smart-AVI SM-EDPN-2Q (4 sidor) i kategorin Växla. Denna guide var användbar för 4 personer och betygsatt med 4.5 stjärnor i genomsnitt av 2 användare

Ladda ner PDF

Sida 1/4

SM-EDPN KVM

with Barco Monitor mdcc-6530

USER MANUAL

Designed and Manufactured in the USA

1-800-284-2131

www.smartavi.com

SM-EDPN-2S 2-Port Single-Head DP KVM Switch with Aux Emulation

SM-EDPN-2D 2-Port Dual-Head DP KVM Switch with Aux Emulation

SM-EDPN-2Q 2-Port Quad-Head DP KVM Switch with Aux Emulation

SM-EDPN-4S 4-Port Single-Head DP KVM Switch with Aux Emulation

SM-EDPN-4D 4-Port Dual-Head DP KVM Switch with Aux Emulation

SM-EDPN-4Q 4-Port Quad-Head DP KVM Switch with Aux Emulation

SM-EDPN-8S 8-Port Single-Head DP KVM Switch with Aux Emulation

2/4/8-Port DP KVM Switch with Audio and USB 2.0 Support 2

Installation

BARCO MONITOR KVM SETUP:

1. Start by connecting your DP input cables from your various devices ONLY to the ports labeled A on

the unit. Then connect the DP output cable from the Barco monitor. This DP cable needs to be from

port marked DP output 1 on the monitor. You should have up to 4 inputs cables coming from various

devices and 1 output cable going to the Barco monitor plugged into the unit at this point.

Note: You must use the cable coming from DP output 1 on the Barco monitor for this process to work. If

you are unsure about which port that is, consult the manual for your respective Barco monitor.

2 3 4 5 6 7

NUMBER DESCRIPTION

1 Kensington security slot

2 Service port (for Barco service purposes only)

3 DisplayPort IN2

4 DisplayPort OUT (covered with a plastic cap by default, remove the cap to use this connector)

5 DisplayPort IN1

6 USB-A 2.0 downstream connectors (2x)

7 USB-B 2.0 upstream connector

8 100-240 VAC mains power input and power switch

2. Make sure your Barco monitor has the correct settings for each video input by using the monitor’s

on-screen display menu. The settings you are looking for in the monitor’s OSD is called EDID timings

and the correct settings are the following: Resolution should be , Refresh Rate should be , 3MP+ High

and Color Depth should be .8 bit

DisplayPort IN1

2/4/8-Port DP KVM Switch with Audio and USB 2.0 Support 3

Installation (continued)

6. Power on the unit. After a few moments, you should now have video on both halves of the Barco

screen. Verify the output video is correct using the same process from step 3. Then enter in the

following sequence on the keyboard: Ctrl + Ctrl + L + 2 + Enter.

7. You can now nish connecting the rest of the cables you have such as other USB cables or audio

cables.

Note: These steps lock the monitor info into the KVM. It will improve performance but if you connect

any other monitor, especially with the strange resolution we’re locking it at, you won’t see video. If you

ever need to use different monitors, be sure to factory reset the KVM with Ctrl + Ctrl + f + enter.

Note: The unit used in the example images is a 4-port quad-head unit, but the instructions are still

applicable to other units such as a 2-port dual-head unit.

3. Power on the unit. After a few moments, you should now see video on one half* of the Barco monitor.

Connect a keyboard and mouse to the K/M slots on the unit. Connect the USB cable (USB male-A

to USB male-B) to the port marked USB for IN 1 on the unit and to a USB port on the device. Check

the video settings to make sure you have the correct resolution, refresh rate, color, and EDID. The

correct settings should be: , , and color. The device’s EDID, device name e.g. 1536x2048 50Hz 8 Bit

MDCC-4430, should also be shown.

* The video should show up on the left side of the monitor. If the video shows up on the right Note:

you’re on DisplayPort IN2. If the video shows up in the center the monitor is set to one source,

change the setting in the monitor to 2 sources.

4. Once you have veried that the resolution is correct, enter the following sequence on the keyboard

to lock the monitor EDID: Ctrl + Ctrl + L + 1 + Enter. This will save the monitors information to the

unit.

5. Power off the unit. Then connect the rest of the inputs to the ports labeled B on the unit. Now swap

the output cable that was previously connected to output labeled A on the unit to the output labeled

B. Then connect the output cable coming from the Barco monitor port labeled DP output 2 to the

output labeled A on the unit.

DisplayPort IN2

DisplayPort IN1

Produktspecifikationer

Varumärke:	Smart-AVI
Kategori:	Växla
Modell:	SM-EDPN-2Q

Behöver du hjälp?

Om du behöver hjälp med Smart-AVI SM-EDPN-2Q ställ en fråga nedan och andra användare kommer att svara dig

Ditt namn*

Din e-post*

Skriv din fråga här

Växla Smart-AVI Manualer

Smart-AVI SM-MST-2D Bruksanvisning

7 Januari 2025

Smart-AVI SM-DVN-84X Bruksanvisning

7 Januari 2025

Smart-AVI HDN-4PLUS-S Bruksanvisning

29 December 2024

Smart-AVI SX-RX200S Bruksanvisning

29 December 2024

Smart-AVI RK-DVX2U-A-RX8S Bruksanvisning

29 December 2024

Smart-AVI RK-DVX2U-A-RX4S Bruksanvisning

29 December 2024

Smart-AVI SX-RX500S Bruksanvisning

29 December 2024

Smart-AVI SDX-PLUS-RX Bruksanvisning

29 December 2024

Smart-AVI HDN-8P Bruksanvisning

29 December 2024

Smart-AVI HDMV-PLUS Bruksanvisning

26 December 2024

Växla Manualer

Nyaste Växla Manualer

Ebara ServoPress LP Bruksanvisning

15 Januari 2025

INOGENI CAM230 Bruksanvisning

14 Januari 2025

Schneider CCT15225 Bruksanvisning

14 Januari 2025

Luxul XMS-5248P Bruksanvisning

14 Januari 2025

Luxul AMS-2624P Bruksanvisning

14 Januari 2025

Luxul XGS-1005 Bruksanvisning

14 Januari 2025

Luxul AGS-1008M Bruksanvisning

14 Januari 2025

Luxul XMS-1208P Bruksanvisning

14 Januari 2025

Luxul XMS-7048P Bruksanvisning

14 Januari 2025

Luxul AMS-2600 Bruksanvisning

14 Januari 2025