SolarEdge ENET-HBCL-01 Bruksanvisning

SolarEdge Inte kategoriserad ENET-HBCL-01

Läs nedan 📖 manual på svenska för SolarEdge ENET-HBCL-01 (3 sidor) i kategorin Inte kategoriserad. Denna guide var användbar för 3 personer och betygsatt med 4.5 stjärnor i genomsnitt av 2 användare

Ladda ner PDF

Sida 1/3

OFF

ENET- -01HBNP

NPNP ENET- -01HBRP

RPRP ENET- -01HBCL

CLCL

1 2 3 4 5

5MIN

1. Install the Antenna

Turn off the inverter

ON/OFF/P switch and DC

safety switch (if applicable).

SolarEdge Energy Net Plug-in Installation

2 -. Install and Connect the Plug in

To avoid electric shock, refer to safety instructions in the inverter

installation guide before removing the inverter cover.

Turn off AC to the

inverter on the main

service panel.

Wait five minutes.

Open the inverter cover and

Connection Unit cover

(if applicable).

Clip the antenna

(supplied) to

a heatsink fin.

Pass the antenna cable

through a communication

gland.

1Connect the Energy Net plug-in to

the dedicated socket on the

communication board.

2Connect the antenna to the

Energy -Net plug in.

Tie the antenna cable to the

communication board bracket

with a plastic tie (supplied).

Mount the inverter cover and

Connection Unit cover (if

applicable). Tighten the screws to

8.4N⋅m/74lb⋅in.

Requires an Energy Net-ready

LCD communication board

SetApp

3. Verify Connection

3Run

SetApp 4Scan the QR code

on the inverter. 5Verify connection.

Commissioning

Status Communication Energy Net

21Turn on the inverter

ON/OFF/P switch and DC

safety switch (if applicable).

Turn on AC to the

inverter on the main

service panel.

The installation of the SolarEdge Energy Net Plug-in must be performed by a qualified installer only.

Make sure to follow all safety and handling instructions specified in the inverter installation guide.

Datasheet

Scan the QR code:

Or follow the link:

https://www.solaredge.com/sites/default/files

/se- - - - -energy net plug in datasheet.pdf

Version 1.0, September 2021

Professional Installation Instructions

Installation P

Installation PInstallation Personnel

ersonnel

ersonnelersonnel

This product is designed for a specific application, and needs to be installed by qualified personnel. The user not attempt to install the product or change any of the product settings.should

External A

External AExternal Antenna

ntenna

ntennantenna

Use only the antennas, which have been approved by the applicant. Unapproved antenna(s) may produce unwanted spurious or excessive RF transmitting power, which may lead to violation of FCC/IC limits and is prohibited.

Federal Communication Commission Inter

Federal Communication Commission InterFederal Communication Commission Interference Statement

ference Statement

ference Statementference Statement

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference

cause undesired operation.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a

installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guar

interference will not occur in a particular installation. If this equipment does cause h s encouraged to try to carmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user i

interference by one of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment.

This transmitter must not be co- located or operating in conjunction with any other antenna or transmitter.

Radiation Exposure Statement

Radiation Exposure StatementRadiation Exposure Statement

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should b minimum distance 20cm between the radiator & your body.e installed and operated with a of

This module is intended for OEM integrators only. Per FCC KDB 996369 D03 OEM Manual v01 guidance, the following conditions must be strictly followed when using this certified module:

• This module has been tested for compliance to FCC Part 15.

• The module is tested for standalone mobile RF exposure use condition.

Any other usage conditions such as co- location with other transmitter(s) or being used in a portable condition will need a separate reassessment through a class II permissive change application or new certification.

RF Exposure C

RF Exposure CRF Exposure Considerati

onsiderati

onsiderationsiderations

ons

onsons

This equipment complies with FCC mobile radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operatthe ed with a minimum distance of 20cm between the radiator & your bo

module is installed in a portable host, a separate SAR evaluation is required to confirm compliance with relevant FCC portable RF exposure rules.

Antennas

AntennasAntennas

The following antennas have been certified for use with this module; antennas of t maintained between thhe same type with equal or lower gain may also be used with this module. The antenna must be installed such that 20 cm can be

and users.

Approved antenna(s) list:

Manufacturer

Manufacturer Manufacturer

Model

ModelModel

Antenna Type

Antenna TypeAntenna Type

Max Gain (dBi)

Max Gain (dBi)Max Gain (dBi)

Impedan

ImpedanImpedance (

ce (

ce (ce (Ω)

)

) )

RALTRON

RST- -TUB7- - -A- TUA3 320020 17M 002

Dipole

3dBi

50ohm

RALTRON

RST- -TUB7- - -A- TUA3 19550200 17M 001

Dipole

3dBi

50ohm

SolarEdge

AS4034-1

Dipole

0dBi

50ohm

SolarEdge

AS4035-1

Coil

0dBi

50ohm

Label and Compliance I

Label and Compliance ILabel and Compliance Information

nformation

nformationnformation

The final end product must be labeled in a visible area with the following: “Contains FCC ID: 2AGPT-ENET ”. The grantee's FCC ID can be used only when all FCC compliance requirements are met.

Information on Test Modes and Additional Testing R

Information on Test Modes and Additional Testing RInformation on Test Modes and Additional Testing Requirements

equirements

equirementsequirements

This transmitter is tested in a standalone mobile RF exposure condition and any co located or simultaneous transmission with other transmitter(s) or portable use will require a separate class II permissive ch evaluation or new ce- ange re-

Additional Testing, Part 15 Subpart B D

Additional Testing, Part 15 Subpart B DAdditional Testing, Part 15 Subpart B Disclaimer

isclaimer

isclaimerisclaimer

This transmitter module is tested as a subsystem and its certification does not cover the FCC Part 15, Subpart B (unintentional radiator) rule requirement applicable to the final host. The final host will still need to be reassessed for com

this portion of rule requirements if applicable.

As long as all conditions above are met, no -further transmitter test will be required. However, the OEM integrator is still responsible for testing their end product for any additional compliance requirements required with this module in

IMPORTANT NOTE: In the event that these conditions can not be met (for example certain laptop configurations or co location with another transmitter), then the FCC authorization is no longer considered valid and the FCC ID can no-

on the final product. In these circumstances, the OEM integrator will be responsible for re- evaluating the end product (including the transmitter) and obtaining a separate FCC authorization.

Manual Informatio

Manual InformatioManual Information to the End User

n to the End User

n to the End Usern to the End User

The OEM integrator has to be aware not to provide information to the end user regarding how to install or remove this RF module in the user’s manual of the end product which integrates this module.

The end user manual shall include all required regulatory information/warning as show in this manual.

OEM/Host Manufa

OEM/Host ManufaOEM/Host Manufacturer R

cturer R

cturer Rcturer Responsibilities

esponsibilities

esponsibilitiesesponsibilities

OEM/Host manufacturers are ultimately responsible for the compliance of the Host and Module. The final product must be reassessed against all the essential requirements of the FCC rule such as FCC Part 15 Subpart B before it can be

the US market. This includes reassessing the transmitter module for compliance with the Radio and EMF essential requirements of the FCC rules. This module must not be incorporated into any other device or system without ret

compliance as multi radio and combined equipment.-

Industry

Industry Industry Canada Statement

Canada Statement

Canada StatementCanada Statement

This device complies with ISED’s licence exempt RSSs. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2- ) This device must accept any interference received, including interfer

may cause undesired operation.

Le présent appareil est conforme aux CNR d’ ISED applicables aux appareils radio exempts de licence. L’exploitation est autorisée aux deux conditions suivantes : (1) le dispositif ne doit pas produire de brouillage préjudiciable, et (2) ce

doit accepter tout brouillage reçu, y compris un brouillage susceptible de provoquer un fonctionnement indésirable.

Radiation Exposure Statement:

Radiation Exposure Statement:Radiation Exposure Statement:

This equipment complies with ISED radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20cm between the radiator & your body.

Déclaration d'exposition aux radiations:

Déclaration d'exposition aux radiations:Déclaration d'exposition aux radiations:

Cet équipement est conforme aux limites d'exposition aux rayonnements ISED établies pour un environnement non contrôlé. Cet équipement doit être installé et utilisé à plus de 20 cm entre le radiateur et votre corps.

This device is intended only for OEM integrators under the following conditions (f : or module device use)

1) The antenna must be installed and operated with a minimum distance of 20cm between the antenna and users, and

2) The transmitter module may not be co located with any other transmitter or antenna.-

As long as 2 conditions above are met, no further transmitter test will be required. However, the OEM integrator is still responsible for testing their end product for any additional compliance requirements required with this module ins-

Cet appareil est conçu uniquement pour les intégrateurs OEM dans les conditions suivantes: (Pour utilisation de dispositif module)

1) L'antenne doit être installé et exploité avec plus de 20 cm entre l'antenne et les utilisateurs, et

2) Le module émetteur peut ne pas être coïmplanté avec un autre émetteur ou antenne.

Tant que les 2 conditions ci-dessus sont remplies, des essais supplémentaires sur l'émetteur ne seront pas nécessaires. Toutefois, l'intégrateur OEM est toujours responsable des essais sur son produit final pour toutes exigences de con

supplémentaires requis pour ce module installé.

IMPORTANT NOTE:

In the event that these conditions can not be met (for example certain laptop configurations or co location with another transmitter), then the Canada authorization is no longer consider- ed valid and the IC ID can not be used on the fi

product. In these circumstances, the OEM integrator will be responsible for re- evaluating the end product (including the transmitter) and obtaining a separate Canada authorization.

NOTE IMPORTANTE:

Dans l rtaines coe cas où ces conditions ne peuvent être satisfaites (par exemple pour certaines configurations d'ordinateur portable ou de ce -localisation avec un autre émetteur), l'autorisation du Canada n'est plus considéré comme va

l'ID IC ne peut pas être utilisé sur le produit final. Dans ces circonstances, l'intégrateur OEM sera chargé de réévaluer le produit final (y compris l'émetteur) et l'obtention d'une autorisation distincte au Canada.

End Product Label

End Product LabelEnd Product Labeling

ing

inging

This transmitter module is authorized only for use in device where the antenna may be installed and operated with a minimum distance of 20cm between the antenna and users. The final end product must be labeled in a visible area w

following: “Contains IC: 20916-ENET ”.

Plaque signalétique du produit final

Ce module émetteur est autorisé uniquement pour une utilisation dans un appareil où l’antenne peut être installée et utilisée à plus de 20 cm entre l’antenne et les utilisateurs. Le produit final doit être étiqueté dans un endroit visible av

l'inscription suivante: "Contient des -ENET 20916 ".

Manual Informatio

Manual InformatioManual Information

n n o the End User

o the End User

o the End Usero the End User

The OEM integrator has to be aware not to provide information to the end user regarding how to install or remove this RF module in the user’s manual of the end product which integrates this module.

The end user manual shall include all required regulatory information/warning as show in this manual.

Le manuel de l utilisateur final doit inclure toutes les informations réglementaires requises et avertissements comme indiqué dans ce manuel.

Detachable Antenna Usage

Detachable Antenna UsageDetachable Antenna Usage

This radio transmitter [IC: antenna types listed below, with the maximum permissible gain indicated. Antenna types not i20916-ENET] has been approved by Innovation, Science and Economic Development Canada to operate with the

this list that have a gain greater than the maximum gain indicated for any type listed are strictly prohibited for use with this device.

Le présent émetteur radio [IC: 20916-ENET -] a été approuvé par Innovation, Sciences et Développement économique Canada pour fonctionner avec les types d'antenne énumérés ci dessous et ayant un gain admissible maximal. Les typ

d'antenne non inclus dans cette liste, et dont le gain est supérieur au gain maximal indiqué pour tout type figurant sur la liste, sont strictement interdits pour l'exploitation de l'émetteur.

Approved antenna(s) list:

Manufacturer

Manufacturer Manufacturer

Model

ModelModel

Antenna Type

Antenna TypeAntenna Type

Max Gain (dBi)

Max Gain (dBi)Max Gain (dBi)

Impedan

ImpedanImpedance (

ce (