Steren USM-8D Bruksanvisning

Läs nedan 📖 manual på svenska för Steren USM-8D (4 sidor) i kategorin AV extender. Denna guide var användbar för 2 personer och betygsatt med 4.5 stjärnor i genomsnitt av 2 användare

Sida 1/4
Installation and
Operation Manual
USM-8D
UHF Consumer Agile Audio-Video Modulator
Operation
Manual
Rev. 03/13
Ph:800-421-6511 www.picodigital.com
USM-8D
Descriptions
Low-cost UHF A/V Agile Modulator adds Satellite, VCR, or Security
Video channels to home distribution network over ultra-band and
UHF band NTSC TV channels 14-83, CATV channels 65-139 –
Double Vestigial Sideband Output 7dBmV minimum, 10dBmV typi-
cal Low Spurious Distortion Frequency Stability Video/250KHz,
Audio +3KHz F-type RF Connectors RCA type A/V Baseband
Connectors – LED Digital Display – PLL Microprocessor-Control
Front Panel Push-Button Channel Selection External UL Power
Adapter Input 120V 60Hz 9W - Output 15VDC 300mA Dimensions
33/8”(L) x 11/ ”8(D) x 33/ ”4(H) – Weight 0.5 lbs
UHF Consumer Agile Audio-Video Modulator
USM-8D
UHF Consumer Agile Audio-Video Modulator
2
Rev. 03/13
Ph:800-421-6511 www.picodigital.com
USM-8D
Controls/Installation/Selection
3
Rev. 03/13
Ph:800-421-6511 www.picodigital.com
UHF Consumer Agile Audio-Video Modulator
1. Band Indicator: When the LED is lit the CATV band is on. When it is off the UHF band is on.
2. Channel Up/Down Selection: UHF: Channels 14 83. Ultra: Channels 65 – 139
3. Mode Switch: Selects UHF: Channels 14 83, Ultra: Channels 65-139 and STD, HRC and IRC formats.
4. Mode Indicator: Indicates STD, HRC or IRC format.
5. Channel Display: Displays channel number and offset format.
6. RF Out: Connect this port to the UHF input of a TV set or cable converter.
7. Audio and Video Inputs: Connect audio and video source to the appropriate input.
8. Power In: Connect an 18Vdc-300mA DC adaptor to this jack.
9. Power Switch: Power on/off switch
Controls
1. Plug in DC power adaptor and connect a cable between adaptor and the USM-8D power jack.
2. Verify the band Indicator located at left of front panel is correctly lit for desired band output.
3. Use UP and DOWN key to select the desired output channel.
4. Connect patch cable between USM-8D video input and your video device source.
5. Connect patch cable between USM-8D audio input and your audio device source.
8. Connect RF OUT to input connection of TV.
Installation
CATV MODE TO TV MODE:
1. Push “MODE” button. Channel number disappears
2. Push channel down button 3 times and red dot will disappear.
3. Push “MODE” button and UHF channel will appear.
4. Push channel up/down buttons for channel of choice.
TV MODE TO CATV MODE:
1. Push button.“MODE”
2. “STD”Push channel up/down button and red dot will appear over
3. “MODE” Push button and CATV channel will appear.
4. Push channel up/down buttons for channel of choice.
OFFSETS AND STANDARD CATV FORMATS:
1. Push “MODE”. Channel number disappears.
2. Use channel up/down buttons to change offset formats.
Channel Selection Ordering Information
USM-8D UHF Consumer Agile Audio-Video
Modulator
1 4 3 2
5
6 8 97
Note: When making channel selection, it is required that a chan-
nel higher or lower be skipped from any existing active
channels. This is to avoid co-channel interference.

Produktspecifikationer

Varumärke: Steren
Kategori: AV extender
Modell: USM-8D

Behöver du hjälp?

Om du behöver hjälp med Steren USM-8D ställ en fråga nedan och andra användare kommer att svara dig




AV extender Steren Manualer

AV extender Manualer

Nyaste AV extender Manualer