System Sensor B300-6 Bruksanvisning

System Sensor Detektor B300-6

Läs nedan 📖 manual på svenska för System Sensor B300-6 (2 sidor) i kategorin Detektor. Denna guide var användbar för 2 personer och betygsatt med 4.5 stjärnor i genomsnitt av 2 användare

Ladda ner PDF

Sida 1/2

INSTALLATION AND MAINTENANCE INSTRUCTIONS

3825 Ohio Avenue, St. Charles, Illinois 60174

1-800-SENSOR2, FAX: 630-377-6495

www.systemsensor.com

BEFORE INSTALLING

Please read the System Smoke Detectors Application Guide, which provides

detailed information on detector spacing, placement, zoning, wiring, and spe-

cial applications. Copies of this application guide are available from System

Sensor. NFPA 72 guidelines should be observed.

NOTICE: This manual should be left with the owner/user of this equipment.

IMPORTANT: The detector used with this base must be tested and maintained

regularly following NFPA 72 requirements. The detector should be cleaned at

least once a year.

GENERAL DESCRIPTION

The B300-6 and B300-6-IV are plug-in detector bases intended for use in an

intelligent system, with screw terminals provided for power (+ and –), and

remote annunciator connections. Communication takes place over the power

lines (+ and –).

BASE TERMINALS

NO. FUNCTION

1 Power (–), Remote Annunciator (–)

2 Power (+)

3 Remote Annunciator (+)

FIGURE 1. TERMINAL LAYOUT

TERMINAL 1

TERMINAL 2

TERMINAL 3

C0127-07

MOUNTING

This detector base mounts directly to 4-inch square (with and without plaster

rings), 4-inch octagon, 3

1/2-inch octagon, and single gang junction boxes. To

mount, remove the decorative ring by turning it in either direction to unhook

the snaps, then separate the ring from the base. Install the base on the box

using the screws supplied with the junction box and the appropriate mounting

slots in the base.

Place the decorative trim ring on the base and rotate it in either direction until

it snaps into place. (See Figure 2.)

SPECIFICATIONS

Base Diameter: 6.1 inches (155 mm)

Base Height: 0.76 inches (19 mm)

Operating Temperature: Refer to applicable sensor Operating Temperature Range using the Base/Sensor Cross Reference Chart at systemsensor.com.

Electrical Ratings:

Operating Voltage: 15 to 32 VDC

Standby Current: 170 µA

Listings: UL268

I56-6566-001

FIGURE 2. MOUNTING DETECTOR TO BOX

SNAP ON

DECORATIVE

RING

SCREWS

(NOT SUPPLIED)

DETECTOR

BASE

BOX

(NOT SUPPLIED)

C2036-01

INSTALLATION AND WIRING GUIDELINES (SEE FIGURE 3)

All wiring must be installed in compliance with all applicable local codes

and any special requirements of the authority having jurisdiction. Proper wire

gauges should be used. The conductors used to connect smoke detectors to

control panels and accessory devices should be color-coded to reduce the like-

lihood of wiring errors. Improper connections can prevent a system from re-

sponding properly in the event of a fire.

For signal wiring (the wiring between interconnected detectors), it is recom-

mended that the wire be no smaller than 18 AWG (0.823 mm²). Wire sizes up

to 12 AWG (3.31 mm²) may be used with the base.

Make electrical connections by stripping about

3/8 inch (10 mm) of insulation

from the end of the wire (use strip gauge molded in base). Then slide the wire

under the clamping plate and tighten the clamping plate screw. Do not loop

the wire under the clamping plate. (See Figure 4.)

Check the zone wiring of all bases in the system before installing the detec-

tors. This includes checking the wiring for continuity, correct polarity, ground

fault testing and performing a dielectric test.

The base includes an area for recording the zone, address, and type of detec-

tor being installed. This information is useful for setting the detector head

address and for verification of the detector type required for that location.

Once all detector bases have been wired and mounted, and the loop wiring

has been checked, the detector heads may be installed in the bases.

B300-6 and B300-6-IV

6" Plug-in Detector Bases

1 I56-6566-001

11/17/2017

System Sensor warrants its enclosed smoke detector base to be free from defects in ma-

terials and workmanship under normal use and service for a period of three years from

date of manufacture. System Sensor makes no other express warranty for this smoke

detector base. No agent, representative, dealer, or employee of the Company has the au-

thority to increase or alter the obligations or limitations of this Warranty. The Company’s

obligation of this Warranty shall be limited to the repair or replacement of any part of

the smoke detector base which is found to be defective in materials or workmanship

under normal use and service during the three year period commencing with the date of

manufacture. After phoning System Sensor’s toll free number 800-SENSOR2 (736-7672)

for a Return Authorization number, send defective units postage prepaid to: Honeywell,

12220 Rojas Drive, Suite 700, El Paso TX 79936 USA. Please include a note describing the

malfunction and suspected cause of failure. The Company shall not be obligated to repair

or replace units which are found to be defective because of damage, unreasonable use,

modifications, or alterations occurring after the date of manufacture. In no case shall the

Company be liable for any consequential or incidental damages for breach of this or any

other Warranty, expressed or implied whatsoever, even if the loss or damage is caused by

the Company’s negligence or fault. Some states do not allow the exclusion or limitation of

incidental or consequential damages, so the above limitation or exclusion may not apply

to you. This Warranty gives you specific legal rights, and you may also have other rights

which vary from state to state.

Please refer to insert for the Limitations of Fire Alarm Systems

THREE-YEAR LIMITED WARRANTY

System Sensor® is a registered trademark of Honeywell International, Inc.

FIGURE 5A. ACTIVATE TAMPER-RESIST FEATURE

PLASTIC LEVER

BREAK TAB AT DOTTED LINE BY

TWISTING WARD CENTER OF BASETO

C0130-00

FIGURE 5B. DETECTOR REMOVAL

USE SMALL-BLADED SCREWDRIVER PUSH TO

PLASTIC LEVER IN DIRECTION OF ARROW

C0130-00

FIGURE 6. CONNECTION TO REMOTE ANNUNCIATOR TERMINAL

STRIPPED WIRE

WIRE WITH SPADE LUG

C0116-00

TAMPER-RESIST FEATURE

NOTE: Do not use the tamper-resist feature if a removal tool will be used.

The detector base includes a tamper-resist feature that prevents removal of the

detector without using a small screwdriver or similar tool.

To activate this feature, use needle-nose pliers to break the tab on the detector

base as shown in Figure 5A. Then, install the detector.

To remove the detector from the base once the tamper-resist feature has been

activated, remove the decorative ring by rotating it in either direction and

pulling it away from the base. Then, insert a small screwdriver into the notch,

as indicated in Figure 5B, and press the plastic lever toward the mounting

surface before rotating the detector counterclockwise for removal.

The tamper-resist feature can be defeated by breaking and removing the plas-

tic lever from the base. However, this prevents the feature from being used

again.

REMOTE ANNUNCIATOR (RA100Z)

Connect the remote annunciator between terminals 1 and 3 using the spade

lug terminal included. The spade lug terminal is connected to the base termi-

nal as shown in Figure 6.

It is not acceptable to have three stripped wires under the same wiring ter-

minal unless they are separated by a washer or equivalent means. The spade

lug supplied with the model RA100Z is considered an equivalent means. See

Figure 3 for proper installation.

FIGURE 3. TYPICAL WIRING DIAGRAM FOR 2-WIRE LOOP

(–)

(+)

+ -

UL LISTED COM TIBLEPA

CONTROL PANEL

CAUTION: DO NO LOOP WIRE T

UNDER TERMINAL 1 OR 2.

BREAK WIRE RUN PROVIDE TO

SUPERVISION OF CONNECTIONS.

CLASS A OPTIONAL WIRING

REMOTE

ANNUNCIATOR

(–)

(+)

C0129-02

FIGURE 4. TERMINAL WIRE INSTALLATION

C0473-00

2 I56-6566-001

Produktspecifikationer

Varumärke:	System Sensor
Kategori:	Detektor
Modell:	B300-6
Färg på produkten:	Roestvrijstaal
Snäll:	Elektronische weegschaal
Automatisk avstängning:	Ja
Beeldscherm:	LCD
Noggrannhet:	- g
Maximal viktkapacitet:	180 kg
Form:	Vierkant
Måttenhet:	kg