Tascam RC-828 Bruksanvisning

Tascam Fjärrkontroll RC-828

Läs nedan 📖 manual på svenska för Tascam RC-828 (7 sidor) i kategorin Fjärrkontroll. Denna guide var användbar för 7 personer och betygsatt med 4.5 stjärnor i genomsnitt av 2 användare

Ladda ner PDF

Sida 1/7

Section 1 – Starting to use the RC-828

0.98 – 1

1 – Starting to use the RC-828

The TASCAM RC-828 Remote Control Unit

allows you to control up to 4 DTRS1 recorders

(any combination of DA-98, DA-38 or DA-98

units) from one location. The functions which

may be controlled are:

• Transport operations (including jog and

shuttle)

• Track arming

• Auto punch operations

• Chasing control

• Location memories and auto-repeat between

two points

This manual makes reference to the manuals of

the following units: DA-88, DA-38, DA-98 and

SY-88. Please consult these documents as neces-

sary when setting up and using the RC-828.

1.1 Hooking up the RC-828

The RC-828 and DTRS units form a “daisy-

chain”, with the RC-828 being at the head, and the

“tail” unit being terminated with the terminator

supplied with the RC-828.

Use the suppled cable to connect the RC-828 to

the REMOTE IN/SYNC IN of the ﬁrst DTRS

unit, and a PW-88S cable to connect the SYNC

OUT of the ﬁrst unit to the REMOTE IN/SYNC

IN of the next unit, and so on, until the terminator

is connected to the SYNC OUT of the last unit in

the chain.

The RC-828’s REC FUNCTION keys 1 through

8 now control the ﬁrst unit, Keys 9 through 16

control the next unit in the chain, and so on

(regardless of the actual Machine IDs of the

units).

Tighten the screws holding the cable connector to

the RC-828 and to the DTRS unit. This will pre-

vent accidental disconnection of the RC-828 in

the middle of a session.

No power connection is needed for the RC-828.

All power for LEDs, etc. is supplied by the ﬁrst

DTRS unit.

1.1.1 Machine IDs

Set the machine IDs of the DTRS units so that the

IDs run in a sequence from the unit at the “head”

of the chain, closest to the RC-828 (lowest possi-

ble ID) to the “tail” unit (highest ID). There

should be no gaps in this sequence.

A DA-88 uses a rotary switch to set the ID and

uses 0 as the lowest ID, and a DA-38 or DA-98

uses software to make this setting, and uses 1 as

the lowest ID. Refer to the units’ manuals for full

details of setting the ID.

1 DTRS is a trademark of TEAC Corporation

NOTE

When you connect a number of DTRS units which are of

dierent types, including a DA-98, the DA-98 should be at

the head of the chain immediately following the RC-828.

Other units may then be connected in any order.

If the DTRS units are DA-88s and DA-38s only, they may

be connected in any order.

WARNING

Turn o power to all units when making connections. If you

do not do this, there is a possibility that the RC-828 will

malfunction or even be damaged.

RC-828 DA-38DA-98 DA-88

OUT OUT OUT

IN IN IN

Terminator

Cable supplied

with RC-828

PW-88S PW-88S

WARNING

Use only TASCAM cables to connect the RC-828 to the ﬁrst

DTRS unit, and to connect the DTRS units to each other. If

the use of cables other than TASCAM cables causes or

results in damage to the units, the warranty is voided.

NOTE

At least one LED is always lit on the RC-828 when it is con-

nected and power is switched on to the DTRS units. If you

do not see any lit LEDs on the RC-828, make sure the

DTRS power is switched on, and check the cable connec-

tions to the RC-828.

Unit

ID as shown

“Real” ID

How the ID is

set (see the

unit’s manual

for details)

Power on or o

when ID is set

DA-98 1 1 Menu system (see

9.2)

DA-88 0 1 Rotary switch on

rear panel (see p23–

24)

OFF

DA-38 1 1 Tape counter menu

system (see 7-2)

Section 2 – Parts of the RC-828

2 – 0.98

1.1.2 Chase mode

In an all-audio setup, the ﬁrst unit is unlikely to be

chasing external sources. However, subsequent

units in the chain should now chase this master,

using the DTRS (ABS) sync method, when their

CHASE switches are pressed.

However, in some audio setups or an audio-visual

setup, it may be necessary to make the master

DTRS unit slave to incoming timecode:

In this case, you should take care to set the clock

reference of the master DTRS unit appropriately.

2 – Parts of the RC-828

[1] REMOTE connector

Connect one end of the supplied cable to this con-

nector, and the other end to the ﬁrst DTRS unit, as

described in 1.1, “Hooking up the RC-828”. Make

sure the power to the DTRS unit is turned o

when you make the connection.

[2] REC FUNCTION keys and

indicators

The 32 REC FUNCTION keys allow you to arm

the tracks of up to four DTRS units. Keys 1–8

control the tracks of the ﬁrst unit in the chain, 9–

16 those of the second, and so on. Pressing keys

which correspond to a non-existent DTRS unit

will have no eect.

Pressing the corresponding keys on the DTRS

units has the same effect as pressing the keys on

the RC-828 unit (i.e. if the track is not armed, it

will now be armed, and vice versa).

The indicators ﬂash when a track is armed for

recording, and light solidly when recording is

being rehearsed or taking place.

[3] CHASE keys and indicators

These keys and indicators allow you to set and

view the chase status of the DTRS units connected

to the RC-828 in the same way as the CHASE

keys and indicators on the units themselves.

[4] ALL INPUT key and indicator

This key performs the same function as the ALL

INPUT key on a DTRS unit, switching the moni-

toring of all tracks on all connected units to the

input source. The indicator lights when this mode

is active.

The INPUT MONITOR keys on the DA-98 also

affect the switching between source and tape.

Using the RC-828 REC FUNCTION keys to

change the status of any tracks while the ALL

INPUT function is on will lose the relationship

between the REC FUNCTION and INPUT

MONITOR status for individual tracks when ALL

INPUT is turned off again. Start recording or re-

set the REC FUNCTION keys to restore this.

If you want to monitor using conﬁdence mode on

a DA-98 unit, make sure that the ALL INPUT key

is off and use the INPUT MONITOR keys on the

DA-98 to turn off input monitoring on all tracks.

[5] AUTO MON key

This key is equivalent to the AUTO MON key on

the DA-98 and performs the same function as this

key on any connected DA-98 units. There is no

key with the same name on the DA-38 or DA-88;

pressing this key is the equivalent of pressing the

INSERT key on a connected DA-38, and pressing

both the AUTO INPUT and INSERT keys on a

DA-88. It is used in punch modes to switch auto-

matically between tape and source when punching

in and out automatically. The indicator lights

when this function is active.

Note that the status of the INPUT MONITOR

keys on a DA-98 will be overridden by the AUTO

MON key. However, when AUTO MON is turned

off again, the original status of these keys will be

restored.

Using the RC-828 REC FUNCTION keys to

change the status of DA-98 tracks while AUTO

MON is on will lose the relationship between the

REC FUNCTION and INPUT MONITOR status

for individual tracks when AUTO MON is turned

off again. Start recording or re-set the REC

FUNCTION keys to restore this.

If you want to monitor using conﬁdence mode on

a DA-98 unit, make sure that the AUTO MON key

NOTE

When you set the machine IDs, you can set the ID of any

machine ﬁrst, but we recommend doing this in a standard

sequence, working from the head of the chain to the tail.

Reference

DA-98 DA-38 DA-88 SY-88

9.2.3 7-3 p. 24 —

Reference

DA-98 DA-38 DA-88 SY-88

10.7.1 — — 5-1

Reference

DA-98 DA-38 DA-88 SY-88

7.1.1 9.1 (1) p. 9 (18) —

Section 2 – Parts of the RC-828

0.98 – 3

is off and use the INPUT MONITOR keys on

the DA-98 to turn off input monitoring on all

tracks.

[6] JOG/SHTL MON key and indicator

This key allows the selection of different monitor-

ing modes when shuttle mode is selected, either

with the units’ own SHUTTLE controls, or from

the JOG/SHUTTLE key on the RC-828 [15].

This key and indicator duplicate the function of

the SHTL MON key and indicator of the DA-98,

and provide these capabilities for the DA-38 and

DA-98.

Use the ﬂowchart provided with this manual to

check the shuttle monitoring status of DA-38 and

DA-88 units in different modes (the provision of

conﬁdence mode on the DA-98 means that this

model differs from the others), and you should

also consult the manual of the DTRS unit for full

details, if you are unclear about how shuttle moni-

toring works:

[7] RHSL key

This key duplicates the functions of the corre-

sponding key controlling rehearsal operations on

the DTRS units. See the appropriate section of the

DTRS manual if you are unsure of its operation.

[8] AUTO PUNCH key

This key duplicates the functions of the corre-

sponding key controlling auto punch operations

on the DTRS units. See the appropriate section of

the DTRS manual if you are unsure of its

operation.

[9] CLEAR key

This key duplicates the functions of the corre-

sponding key clearing punch points on the DTRS

units. See the appropriate section of the DTRS

manual if you are unsure of its operation.

[10] LOCATE POINTS 1–12

These 12 location keys and indicators are used for

the management of location memories. These

memories are stored and used with reference to

the DTRS unit’s current time reference (ABS or

timecode).

The indicator of a location memory containing a

location point will be lit, and pressing the key

(except in “capture” or erase mode, see [11] and

[12]) will locate to the point stored in that mem-

ory. Pressing a key whose indicator is not lit will

have no effect. The location point stored in the

memory will be brieﬂy shown on the tape counter

of the DTRS units (for the DA-88 and DA-38–for

the DA-98 the location point will be shown brieﬂy

on the LCD display screen).

While location is taking place, the indicator will

ﬂash, and the indicator will light steadily again

when location is complete.

If the AUTO PLAY indicator [13] is lit, the DTRS

unit will start to play back when the location point

is reached, otherwise the transport will stop at the

location point.

[11] CAPTURE key and indicator

Press this key to enter “capture” mode. The green

indicator will ﬂash. While in capture mode, press-

ing a LOCATE POINT key [10] will store the

current tape position to the location memory cor-

responding to the LOCATE POINT key.

If the memory does not contain data (the indicator

is not lit), the new position will be written to the

memory and the indicator will light. If the mem-

ory already contains a location point (the indicator

is lit), this will be overwritten with the new posi-

tion. Press the CAPTURE key again to turn off

the capture mode (the indicator will stop ﬂashing).

[12] ERASE key

To erase a location memory, press and hold down

the ERASE key. While holding it down, press the

LOCATE POINT key [10] of the memory you

want to erase. The indicator of the LOCATE

Reference

DA-98 DA-38 DA-88 SY-88

7.1.3 — — —

Reference

DA-98 DA-38 DA-88 SY-88

6.6 4-3 p. 16 —

NOTE

These location memories are independent of the MEMO 1

and 2 location memories stored in the DTRS units.

NOTE

The location points are stored in memory, backed up by a

battery whose life is a few years. When you turn on the

DTRS unit connected to the RC-828 with location memo-

ries stored in it, the same location indicators will light as

were lit at the time when you last turned o the DTRS unit.

If they do not light, the battery needs replacing, and you

should contact your TASCAM dealer regarding a replace-

ment battery.

Produktspecifikationer

Varumärke:	Tascam
Kategori:	Fjärrkontroll
Modell:	RC-828

Behöver du hjälp?

Om du behöver hjälp med Tascam RC-828 ställ en fråga nedan och andra användare kommer att svara dig

Ditt namn*

Din e-post*

Skriv din fråga här

Fjärrkontroll Tascam Manualer

Tascam SS250 Control Bruksanvisning

29 September 2024

Tascam RC-10 Bruksanvisning

16 September 2024

Tascam RC-HS20PD Bruksanvisning

23 Augusti 2024

Tascam RC-900 Bruksanvisning

8 Augusti 2024

Tascam RC-828 Bruksanvisning

6 Augusti 2024

Fjärrkontroll Manualer

Nyaste Fjärrkontroll Manualer

Monacor DRM-880WP Bruksanvisning

27 Oktober 2024

Hama Spot-Pointer V2 Bruksanvisning

26 Oktober 2024

Sony RM-ED022 Bruksanvisning

21 Oktober 2024

Sonos Control Bruksanvisning

18 Oktober 2024

One For All URC 7935 Bruksanvisning

18 Oktober 2024

Canon BG-E20 Bruksanvisning

12 Oktober 2024

Neewer RT112 Bruksanvisning

8 Oktober 2024

Neewer RT113 Bruksanvisning

8 Oktober 2024

Logitech Harmony 785 Bruksanvisning

8 Oktober 2024

DSC WS4949 Bruksanvisning

8 Oktober 2024