Techno Line WS 6830 Bruksanvisning

Techno Line Väderstation WS 6830

Läs nedan 📖 manual på svenska för Techno Line WS 6830 (1 sidor) i kategorin Väderstation. Denna guide var användbar för 2 personer och betygsatt med 4.5 stjärnor i genomsnitt av 2 användare

Ladda ner PDF

Sida 1/1

Installation

1. Insert the round base to the back pole (as indicated)

of your LED weather station, turn the base to the right

to secure it in position.

2. Plug the AC/DC adaptor into any 230V European

AC household outlet. Plug the DC jack into the lower

back of the clock. The top front of the clock will show

and the indoor-outdoor temperatures and

weather forecast display will appear. Your LED weather

station is ready to work for you.

Battery Back Up

1. Slide the battery door at the back case, insert 3 x AAA batteries with correct + and - polarity signs inside

the battery compartment. Replace the battery cover.

2. When AC power is off, the batteries will power t he clock to keep track of the time and alarm time.

3. When only the back-up batteries is used, the LED panel is off.

Power Up Reception and Signal Strength Display

1. After plug in AC power, the clock starts to receive DCF signal.

Icon blinks. Display shows

2. When strong DCF signal is detected, display shows with 3 bars

When weak or no DCF signal is detected, display shows with 1 bar

or . You will need to place the clock to another area for better

reception, or unplug the AC/DC jack to start over reception again. During

reception, the signal strength may move from 1 bar to 2 bars to 3 bars. This

is normal since the clock is detecting DCF signal and other signals in the

air at the same time.

3. If the clock does not catch DCF time signal for 7 minutes, it will go back

to normal time display

4. During reception, press TIME button once will go to normal time

display.

Press HR again will return to reception mode and signal strength indication.

Successful reception or failed reception

Icon becomes static on (stop blinking) when reception is successful Icon

disappears when reception is failed

Weak or no RC signal Is

detected

Successful Reception

Automatic Reception and Manual Reception

Automatic reception : this clock starts reception automatically everyday at 1:00am. If auto recpetion fails at

1:00 am, it will start again at 2:00 am. If fails at 2:00 am, it will start again at 3:00 am.

If auto recpetion fails at 3:00 am still fails, it will start reception every 3 hours until it succeeds to catch correct

DCF time.

Manual reception : press HR button once anytime to start manual reception of DCF time signal. The LED time

display will go to radio controlled reception mode

To Set Time and Alarm Time

After power up, if press TIME button once, time digits go to 0:00 am (default

start-up time). The clock continues to receive DCF signal. The icon is still

blinking.

Press HR button once will go back to radio controlled reception mode (as above)

TO SET TIME

Press and hold TIME button and at the same time press HR button once at a time

to set hour.

Press and hold TIME button and at the same time press MIN button once at a time

to set minute.

SET ALARM 2

TO SET ALARM 1 TIME

1. Slide the Alarm Switch to 1. ALM

2. Press and hold button and at the same time press HR button once at a time to set hour. ALM

3. Press and hold button and at the same time press button once at a time to set minute. ALM MIN

TO SET ALARM 2 TIME

1. Slide the Alarm Switch to 2. ALM

2. Press and hold button and at the same time press HR button once at a time to set hour. ALM

3. Press and hold button and at the same time press button once at a time to set minute. ALM MIN

TO TURN ON/OFF ALARM 1 or/and ALARM 2

1. To turn on Alarm 1 only, slide the alarm switch to ALM 1, ALM 1 LED lights up on upper left of the hour

digits.

2. To turn on Alarm 2 only, slide the alarm switch to ALM 2, ALM 2 LED lights up on lower left of the hour

digits.

3. To turn on both and slide the alarm switch to 1 + 2, both ALM 1 and ALM 2 LED light up. Alarm 1 2, ALM

4. To in-activate both Alarm 1 2 and permanently, slide to ALM OFF. Both ALM 1 and ALM 2 LED turn off.

TO USE THE SNOOZE ALARM

When time reaches the set ALARM 1 and/or ALARM 2 time, the clock will beep with the ALM 1 and/or ALM 2

LED blinking.

Press the SNOOZE button once, the alarm sound will stop and ALM ALM 1 or 2 LED keep blinking. Alarm will

sound againin 5 minutes.

TO STOP THE ALARM

When time reaches the set ALARM 1 and/or ALARM 2 time, the clock will beep with the ALM 1 and/or ALM 2

LED blinking.

Press and hold the SNOOZE button for 2 seconds, the alarm sound will stop and ALM 1 or ALM 2 LED

becomes static. Alarm 1 and/or Alarm 2 will sound again same time next day.

TO TURN OFF ALARM 1 AND/OR ALARM 2 PERMANENTLY

Slide the alarm switch to ALM OFF. ALM ALM Alarm sound will stop and both 1 and 2 LED's turn off.

TO SET SNOOZE DURATION (from 5 to 60 minutes)

Press and hold and time display will show "05" (default snooze duration) and then press SNOOZE MINUTE

button to set your desired snooze duration.

TO READ MAXIMUM-MINUMUM INDOOR-OUTDOOR TEMPERATURES

Simply press the button to view the maximum indoor and outdoor temperatures. Press MAXCLEAR to reset the

Max readings. The readout will now appear as — and will start to record the maximums again.

Then press the button to view the minimum indoor and outdoor temperatures. Press MAXMINCLEAR to reset the

Min readings. The readout will now appear as — and will start to record the minimums again.

IF YOU LOSE THE OUTDOOR TEMPERATURE

When the outdoor temperature digits show '—--", the wireless transmission is either interrupted or lost. Press the

CLEAR RESET button at the back of your LED weather station, then press button at the back of the outdoor

transmitter. If you continue to lose the outdoor temperature display, try placing the transmitter in a different

location until you have smooth transmission of temperature data.

USING THE WEATHER FORECASTER AND BAROMETER

Your LED weather station has a built-in barometer which measures the barometric pressure. After power up,

the display shows Sunny & Cloudy icons. Your LED weather station takes around 24 hours to gather data of

barometric pressure changes and predicts next 1 2- 24 hours weather conditions.

There are four types of weather display of the predicted weather condition :

TROUBLE SHOOTING

Press the RESET button on the back of the base thermometer and then press RESET button located on the

back of the outdoor transmitter. Once you do this, your clock will be reset to default setting and needs to be

up-dated by DCF time signal again.

TO USE THE HI-LO DIMMER SWITCH

Simply slide the LO-HI DIMMER switch at the back of the clock to adjust the LED brightness to a comfortable

level to you in the dark.

CARE OF YOUR CLOCK

1. Do not expose your clock to extreme temperatures, water or direct sunlight.

2. Avoid contact with any corrosive materials

3. Do not subject the clock to excessive force, dust or humidity

4. Do not open the inner back case or tamper with any components of this clock

5. Do not plug in any other AC/DC adaptor with incorrect specifications or voltage

6. Do not place your clock in range of strong interferences. (TV, Microwave…)

SUNNY SUNNY & CLOUDY CLOUDY RAINY

Your weather forecaster also has weather tendency indicator, when the air pressure is going up (the weather will

improve) the UP arrow will appear, when the air pressu re is going down (the weather will go worse) the DOWN

arrow will appear.

Remarks : Moving your weather station around your house or your building will affect its accuracy because the

sudden change of temperature or height/altitude will affect the accuracy of your weather station. It

will take 24 hours to get stable again to predict next 12-24 hours weather condition.

Your weather station predicts next 12 - 24 hours weather conditions. It may not match with the current weather

condition outside.

Instruction Manual

WS 6830

RC tower Icon blinking

Strong DCF signal is detected,

Minut e digits may start counting

01,02,03. ..60,00,01,02.... tryin g

to match with the correct seconds

DfJJY signal

Failed Reception

SET ALARM 1

Produktspecifikationer

Varumärke:	Techno Line
Kategori:	Väderstation
Modell:	WS 6830
Färg på produkten:	Zwart
Vikt:	110 g
Bredd:	64 mm
Djup:	97 mm
Höjd:	25 mm
Förpackningens vikt:	110 g
Snäll:	Netwerkrepeater
LED-indikatorer:	Ja
Antal Ethernet LAN (RJ-45)-portar:	2
Nätverksstandard:	IEEE 802.3af, IEEE 802.3at
Power over Ethernet (PoE):	Ja
Maximal-räckvidd:	100 m
Drifttemperatur (TT):	0 - 49 °C
Antal Power over Ethernet-portar (PoE).:	2
Antal RJ-45-portar (mottagare):	1
Antal RJ-45-portar (sändare):	1