Toshiba RAS-13SKV Bruksanvisning

Toshiba Luftkonditionering RAS-13SKV

Läs nedan 📖 manual på svenska för Toshiba RAS-13SKV (8 sidor) i kategorin Luftkonditionering. Denna guide var användbar för 5 personer och betygsatt med 4.5 stjärnor i genomsnitt av 2 användare

Ladda ner PDF
Sida 1/8
E N G L I S H
O W N E R’ S M A N U A L
AIR CONDITIONER (SPLIT TYPE)
For general public use
Indoor unit
RAS-10, 13, 16 SKV Series
Outdoor unit
RAS-10, 13, 16 SAV Series
1110250102-(1).indd 1
1110250102-(1).indd 1
1110250102-(1).indd 1
1110250102-(1).indd 11110250102-(1).indd 1
1110250102-(1).indd 1
1/4/07 4:48:00 PM
1/4/07 4:48:00 PM
1/4/07 4:48:00 PM
1/4/07 4:48:00 PM1/4/07 4:48:00 PM1/4/07 4:48:00 PM
1
Press
FIX
: Move the louver in the
desired vertical direction.
2
Press
SWING
: Swing the air
automatically and press again to stop.
3
For horizontal direction, adjust
manually.
DANGER
•
Do not install, repair, open or remove the cover. It may expose you
to dangerous voltages. Ask the dealer or the specialist to do this.
•
Turning off the power supply will not prevent potential electric
shock.
•
The appliance shall be installed in accordance with national wiring
regulation.
•
Means for disconnection from the supply having a contact
separation of at least 3 mm in all poles must be incorporated in the
fi xed wiring.
WARNING
•
Do not expose your body directly to cool air for a long time.
•
Do not insert your fi nger or any article into the air inlet/outlet.
•
When an abnormality (burning smell, etc.) occurs, stop the air
conditioner and disconnect the power supply or turn off the
breaker.
CAUTION
•
Do not wash the unit with water. It may cause an electric shock.
•
Do not use this air conditioner for other purposes such as
preserving food, breeding animal, etc.
•
Do not step or put anything on the indoor/outdoor unit. It may
cause an injury or damage the unit.
•
Do not touch aluminium fi n because it may cause an injury.
•
Before cleaning the unit, turn off the main switch or the circuit
breaker.
•
When the unit won’t be used for a long time, turn off the main
switch or the circuit breaker.
•
It is recommended that maintenance be performed by a specialist
when the unit has been operated for a long time.
PRECAUTIONS FOR SAFETY
INDOOR UNIT DISPLAY
1 Hi POWER (Green)
2 FILTER (Orange)
3 PURE (Blue) (10, 13, 16SKVR-A series)
3 PRE DEF (DE-FROST) (Orange)
(13, 16SKV-A series)
4 TIMER (Yellow)
5 OPERATION (Green)
6 RESET button
1
Hi POWER FILTER PURE TIMER OPERATION
RESET
1 2 3
4 5
6
PREPARATION BEFORE USE
2
Preparing Filters
1. Open the air inlet grille and remove the air fi lters.
2. Attach the fi lters. (see detail in the accessory sheet).
Loading Batteries
1. Remove the battery cover.
2. Insert 2 new batteries (AAA type)
following the (+) and (–) positions.
Clock Setup
1. Push CLOCK ● by tip of the pencil.
2. Press ON or OFF : adjust the time.
3. Press SET : Set the time.
Remote Control Reset
1. Remove the battery.
2. Press .
3. Insert the battery.
AIRFLOW DIRECTION
3
• Do not move the louver manually by others.
• The louver may automation positioning by come operation mode.
Note:
REMOTE CONTROL
4
PRESET
ONE-TOUCH
QUIET
SWING
TIMER
ON
FILTER
CHK
CLOCK
OFF
CLR
SLEEP
SET
FIX Hi-POWER ECO
PURE
COMFORT
SLEEP
MODE
TEMP
FAN
5
4
3
~
(
&
9
-
"
#
$
%
)
,
.
8
7
6
+
1
1 Infrared signal emitter
2 Start/Stop button
3 Mode select button (MODE)
4 Temperature button (TEMP)
5 Fan speed button (FAN)
6 Swing louver button (SWING)
7 Set louver button (FIX)
8 On timer button (ON)
9 Off timer button (OFF)
! Sleep timer button (SLEEP)
" Setup button (SET)
# Clear button (CLR)
$ Memory and Preset button (PRESET)
% One Touch button (ONE-TOUCH)
& High power button (Hi-POWER)
( Economy button (ECO)
) Quiet button (QUIET)
~ Comfort sleep button (COMFORT SLEEP)
+ Plasma Air Purifi er button (PURE)
(RAS-10, 13, 16SKVR-A Only)
, Filter reset button (FILTER)
- Clock Reset button (CLOCK)
. Check button (CHK)
ONE-TOUCH
5
Press the “ONE-TOUCH” button for fully automated operation that is customised
to the typical consumer preferences in your region of the world. The customised
settings control temperature air fl ow strength, air fl ow direction and other settings
to provide you alternate contact with “ONE-TOUCH” of the button. If you prefer
other settings you can select from the many other operating functions of your
Toshiba unit.
Press
ONE-TOUCH
: Start the operation.
AUTOMATIC OPERATION
6
To automatically select cooling, heating, or fan only operation
1. Press
MODE
: Select A.
2. Press
TEMP
: Set the desired temperature.
COOLING / HEATING / FAN ONLY OPERATION
7
1. Press
MODE
: Select Cool , Heat , or Fan only .
2. Press
TEMP
: Set the desired temperature.
Cooling: Min. 17oC, Heating: Max. 30oC, Fan Only: No temperature indication
3. Press
FAN
: Select AUTO, LOW , LOW+ , MED , MED+ , or
HIGH .
DRY OPERATION
8
For dehumidifi cation, a moderate cooling performance is controlled
automatically.
1. Press
MODE
: Select Dry .
2. Press
TEMP
: Set the desired temperature.
AIR PURIFYING OPERATION
(RAS-10, 13, 16SKVR-A Only)
9
During air conditioner operation
Press
PURE
to start and stop plasma air purifi er and air ionizer operation.
The plasma air purifi er and air ionizer can be activated or deactivated during air
conditioner is stopped and the air ionizer starts in conjunction with plasma air
purifi er operation.
Note: The FILTER indicator (orange) turns on after PURE operation is performed
for about 1000 hours.
2
A
CL
Hi-POWER OPERATION
10
To automatically control room temperature and airfl ow for faster cooling or heating
operation (except in DRY and FAN ONLY mode)
Press
Hi-POWER
: Start and stop the operation.
ECO OPERATION
11
To automatically control room to save energy (except in DRY and FAN ONLY
mode)
Press
ECO
: Start and stop the operation.
Note: Cooling operation; the set temperature will increase automatically 1 degree/
hour for 2 hours (maximum 2 degrees increase). For heating operation the
set temperature will decrease.
CLEANING
RESET TIMER OPERATION
3 2 1
1 OPERATION (Green)
2 TIMER/CLEANING (Yellow)
3 RESET button
Models: RAS-10, 13, 16SKVR-A, RAS-13, 16SKV-A
Models: RAS-10SKV-A
!
1110250102-(1).indd 2
1110250102-(1).indd 2
1110250102-(1).indd 2
1110250102-(1).indd 21110250102-(1).indd 2
1110250102-(1).indd 2
1/4/07 4:48:03 PM
1/4/07 4:48:03 PM
1/4/07 4:48:03 PM
1/4/07 4:48:03 PM1/4/07 4:48:03 PM1/4/07 4:48:03 PM
TEMPORARY OPERATION
12
In case of the misplaced or discharged remote control
• Pressing the RESET button, the unit can start or stop
without using the remote control.
• Operation mode is set on AUTOMATIC
operation, preset temperature is 24°C
and fan operation is automatic speed.
TIMER OPERATION
13
Everyday timer allows the user to set both the ON & OFF timers and will be activated on a daily basis.
Setting the ON Timer Setting the OFF Timer
1
Press
ON
: Set the desired ON timer.
Press
OFF
: Set the desired OFF timer.
2Press SET : Set the timer. Press SET : Set the timer.
3Press
CLR
: Cancel the timer. Press
CLR
: Cancel the timer.
• Keep the remote control in accessible transmission to the indoor unit;
otherwise, the time lag of up to 15 minutes will occur.
• The setting will be saved for the next same operation.
Note:
Setting Everyday Timer
1Press
ON
: Set the ON timer. 3Press SET .
2Press
OFF
: Set the OFF timer. 4Press SET button during the ( or )
mark fl ashing.
• During the every day timer is activating, both arrows ( , ) are indicated.
PRESET OPERATION
14
Set your preferred operation for future use. The setting will be memorized by the
unit for future operation (except airfl ow direction).
1. Select your preferred operation.
2. Press and hold
PRESET
for 3 seconds to memorize the setting. The P mark
displays.
3. Press
PRESET
: Operate the preset operation.
AUTO RESTART OPERATION
15
To automatically restart the conditioner after the power failure (Power of the unit
must be on.)
Setting
1. Press and hold the RESET button on the indoor unit for 3 seconds to set the
operation. (3 beep sound and OPERATION lamp blink 5 time/sec for 5 seconds)
• Do not operate ON timer and OFF timer.
2. Press and hold the RESET button on the indoor unit for 3 seconds to cancel the
operation. (3 beep sound but OPERATION lamp does not blink)
To operate at super low fan speed for quiet operation (except in DRY mode)
Press
QUIET
: Start and stop the operation.
Note: Under certain conditions, QUIET operation may not provide adequate
cooling or heating due to low sound features.
To save energy while sleeping, automatically control air fl ow and automatically
turn OFF.
Press
COMFORT
SLEEP
: Select 1, 3, 5 or 9 hrs for OFF timer operation.
Note: The cooling operation, the set temperature will increase automatically
1 degree/hour for 2 hours (maximum 2 degrees increase). For heating
operation, the set temperature will decrease.
Cleaning the plasma air purifi er unit (About 1000 hours performed)
(RAS-10, 13, 16SKVR-A Only)
1. Turn off air conditioner using remote control and power supply.
2. Take out the air inlet grille (See detail in installation manual).
3. Take out the plasma air purifi er by grasp the handle, and the pull it out.
4. Soak in hot water at 40oC to 50oC for about 10 to 15 minutes and rub up,
down, left, right and rub surface gently with a sponge.
5. Allow to dry thoroughly in the shade.
6. Attach the plasma air purifi er by grasp the
handle and insert into the right and left
guide rails.
7. Press both ends of the plasma air purifi er
until the protrusions on both sides of the
plasma air purifi er are completely inserted.
8. Attach the air fi lter, and then close the air
inlet grille.
QUIET OPERATION
16
COMFORT SLEEP OPERATION
17
SELF CLEANING OPERATION (COOL AND DRY OPERATION ONLY)
20
OPERATION AND PERFORMANCE
21
1. Three-minute protection feature: To prevent the unit from being activated for 3
minutes when suddenly restarted or switched to ON.
2. Preheating operation: Warm up the unit for 5 minutes before the heating
operation starts.
3. Warm air control: When the room temperature reaches the set temperature,
the fan speed is automatically reduced and the outdoor unit will stop.
4. Automatic defrosting: Fans will stop during defrost operation.
5. Heating capacity: Heat is absorbed from outdoors and released into the room.
When the outdoor temperature is too low, use another recommended heating
apparatus in combination with the air conditioner.
6. Consideration for accumulated snow: Select the position for outdoor unit
where it will not be subjected to snow drifts, accumulation of leaves or other
seasonal debris.
7. Some minor cracking sound may occur when unit operating. This is normal
because the cracking sound may be caused by expansion/contraction of
plastic.
Item 2 to 6 for Heating model Note:
Air conditioner operating conditions
Temp.
Operation
Outdoor Temperature Room
Temperature
10, 13, 16SKVR-A
13, 16SKV-A 10SKV-A
Heating –15°C ~ 24°C –10°C ~ 24°C Less than 28°C
Cooling –10°C ~ 46°C 15°C ~ 43°C 21°C ~ 32°C
Dry –10°C ~ 46°C 15°C ~ 43°C 17°C ~ 32°C
The unit does not operate.
Cooling or Heating is abnormally low.
• The power main switch is turned off.
• The circuit breaker is activated to
cut off the power supply.
• Stoppage of electric current
• ON timer is set.
• The fi lters are blocked with dust.
• The temperature has been set
improperly.
• The windows or doors are opened.
• The air inlet or outlet of the outdoor
unit is blocked.
• The fan speed is too low.
• The operation mode is FAN or DRY.
TROUBLESHOOTING (CHECK POINT)
22
REMOTE CONTROL A-B SELECTION
23
To separate using of remote control for each indoor unit in case of 2 air conditioner
are installed nearly.
Remote Control B Setup.
1. Press RESET button on the indoor unit to turn the air conditioner ON.
2. Point the remote control at the indoor unit.
3. Push and hold CHK ●
button on the Remote Control by the tip of the pencil. “00” will
be shown on the display.
4. Press
MODE
during pushing CHK ●. “B” will show on the display and “00”
will disappear and the air conditioner will turn OFF. The Remote Control B is
memorized.
Note: 1. Repeat above step to reset Remote Control to be A.
2. Remote Control A has not “A” display.
3. Default setting of Remote Control from factory is A.
To start the sleep timer (OFF timer) operation
Press
SLEEP
: Select 1, 3, 5 or 9 hrs for OFF timer operation.
SLEEP TIMER OPERATION
18
Firstly, turn off the circuit breaker.
Filter Reset (Some models only)
FILTER lamp lights on; the fi lter must be cleaned.
To turn off the lamp, push the RESET button on the indoor unit or the FILTER
button on the remote control.
Indoor Unit and Remote Control
• Clean the indoor unit and the remote control with a wet cloth when needed.
• No benzine, thinner, polishing powder or chemically-treated duster.
Cleaning the air ionizer (Once every six months) (RAS-10, 13, 16SKVR-A Only)
1. Turn off air conditioner using remote control and power supply.
2. Fully open the vertical air fl ow louvers by hand.
3. Use a toothbrush to rub the ends of metal pin three or four times.
Note: Do not use cotton swabs or other objects with fl uff.
MAINTENANCE
19
To protect bad smell caused by the humidity in the indoor unit.
1. If the button is pressed once during “Cool” or “Dry” mode, the fan will continue
to run for other 20 minutes, then it will turn off automatically. This will reduce the
moisture in the indoor unit.
2. To stop the unit immediately, press the 3 times within 30 seconds.
Note:
• SELF CLEANING operation is default setting from factory.
• To cancel this function, press and hold the reset button on the indoor unit for 20
seconds.
The SELF CLEANING operation will be cancelled. (5 beep sound but OPERATION
lamp does not blink)
• Do the same to set this function again. (5 beep sound and OPERATION lamp
blink 5 time/sec for 5 seconds)
• AUTO RESTART operation will be cancelled by setting or cancellation of SELF
CLEANING operation. Set it again if necessary.
EN
1110250102-(1).indd 3
1110250102-(1).indd 3
1110250102-(1).indd 3
1110250102-(1).indd 31110250102-(1).indd 3
1110250102-(1).indd 3
1/4/07 4:48:08 PM
1/4/07 4:48:08 PM
1/4/07 4:48:08 PM
1/4/07 4:48:08 PM1/4/07 4:48:08 PM1/4/07 4:48:08 PM

Produktspecifikationer

Varumärke: Toshiba
Kategori: Luftkonditionering
Modell: RAS-13SKV

Behöver du hjälp?

Om du behöver hjälp med Toshiba RAS-13SKV ställ en fråga nedan och andra användare kommer att svara dig


Luftkonditionering Toshiba Manualer

Toshiba

Toshiba RAS-12LAV-UL Bruksanvisning

21 Oktober 2024
Toshiba

Toshiba RAS-B10SKVP-E Bruksanvisning

20 Oktober 2024
Toshiba

Toshiba RAS-13SKV Bruksanvisning

20 Oktober 2024
Toshiba

Toshiba RAS-15LKV-UL Bruksanvisning

20 Oktober 2024
Toshiba

Toshiba MCY-MAP0501HT Bruksanvisning

13 Oktober 2024
Toshiba

Toshiba RAS-25G2AVP-ND Bruksanvisning

4 Oktober 2024
Toshiba

Toshiba MCY-MAP0401HT Bruksanvisning

23 September 2024
Toshiba

Toshiba RAS-34E2KVG-A Bruksanvisning

19 September 2024
Toshiba

Toshiba RAS-07E2KV2G-A Bruksanvisning

19 September 2024
Toshiba

Toshiba RAS-22E2KV2G-A Bruksanvisning

19 September 2024

Luftkonditionering Manualer

Nyaste Luftkonditionering Manualer

Kenmore

Kenmore 580.77157 Bruksanvisning

27 Oktober 2024
Philco

Philco PSV12HRJ-A2 Bruksanvisning

27 Oktober 2024
BEKO

BEKO BIHPR 120 Bruksanvisning

27 Oktober 2024
General Electric

General Electric AEQ10 Bruksanvisning

27 Oktober 2024
Fujitsu

Fujitsu AIRSTAGE AJY040LBLDH Bruksanvisning

27 Oktober 2024
REMKO

REMKO RM426 Bruksanvisning

27 Oktober 2024
Delonghi

Delonghi Pinguino Arctic Whisper PACEX390LVYN-6AWH Bruksanvisning

26 Oktober 2024
Trisa

Trisa Cool Mate 9362.70 Bruksanvisning

26 Oktober 2024
Hotpoint

Hotpoint AHES09D2XXA Bruksanvisning

26 Oktober 2024
ARCTIC WIND

ARCTIC WIND 3AWTWH120002A Bruksanvisning

26 Oktober 2024