Ultimaker 2+ Connect Bruksanvisning
Läs nedan 📖 manual på svenska för Ultimaker 2+ Connect (39 sidor) i kategorin Skrivare. Denna guide var användbar för 2 personer och betygsatt med 4.5 stjärnor i genomsnitt av 2 användare
Sida 1/39

Ultimaker 2+ Connect
Installation and user manual
EN 10/2020 v1.0 Original instructions

Ultimaker 2+ Connect user manual 1
Table of contents
1. Safety and compliance
1.1 Safety messages 4
1.2 General safety information 4
1.3 Hazards 5
1.4 Regulatory information 6
2. Introduction
2.1 Main components 9
2.2 Specications 11
3. Installation
3.1 Unboxing 13
3.2 What's in the box? 14
3.3 Hardware installation 15
3.4 First setup 16
3.5 Firmware update 17
3.6 Install Ultimaker Cura 18
4. Operation
4.1 Touchscreen 20
4.2 Materials 21
4.3 Preparing a print with Ultimaker Cura 22
4.4 Printing with the Air Manager 24
4.5 Remove the print 25
4.6 Change the printer conguration 26
5. Maintenance
5.1 Update the rmware 28
5.2 Material handling and storage 28
5.3 Maintenance schedule 29
5.4 Replace the Air Manager lter 30
6. Troubleshooting
6.1 Error messages 32
6.2 Extrusion problems 32
6.3 Adhesion issues 33
6.4 Air Manager troubleshooting 34
7. Warranty
7.1 General 36
7.2 Conditions 36
7.3 Notication 37
7.4 Exclusions 37
7.5 Applicable law and competent court 37

Ultimaker 2+ Connect user manual 2
Disclaimer
This manual sets out the instructions on how to install and operate the Ultimaker 2+ Connect. Please read and
understand the contents of this installation and user manual carefully. Failure to read the manual may lead to
personal injury, inferior print results or damage to the Ultimaker printer or its peripherals. Always make sure that
anyone who uses this 3D printer knows and understands the contents of the manual to make the most out of
the Ultimaker printer.
Upon delivery of the product, installation shall be done in accordance with the instructions in this user manual. The
handling, storage, use, or disposal of the device are beyond our control and are for your sole responsibility. We do
not assume responsibility and expressly disclaim liability for loss, injuries, damage, or expense arising out of or in
any way connected with the handling, storage, use, or disposal of the product.
The information within this document has been collected and represented with great care and is considered
accurate. In case inconsistencies or inaccuracies are observed those are unintentional and Ultimaker welcomes to
be made aware of those. Submit your feedback to Ultimaker via ‘Submit a request’ at support.ultimaker.com.
Intended use
Ultimaker 3D printers are designed and built for fused lament fabrication with Ultimaker materials mainly within
a commercial, professional, or educational environment. The mixture of precision and speed makes Ultimaker 3D
printers very suitable for concept models, functional prototypes, and small series production.
The Ultimaker 2+ Connect, with its networking capabilities and new touchscreen, delivers single extrusion for
simple applications.
Although we achieved a very high standard in the reproduction of 3D models with the usage of Ultimaker Cura,
the user remains responsible to qualify and validate the application of the printed object for its intended use. This
is especially critical for applications in strictly regulated areas like medical devices and aeronautics. While being
an open material platform, the best results will be achieved with Ultimaker materials, as eort has been made to
match material properties with machine settings.
Produktspecifikationer
Varumärke: | Ultimaker |
Kategori: | Skrivare |
Modell: | 2+ Connect |
Färg på produkten: | Zwart |
Vikt: | 115 g |
Bredd: | 30 mm |
Djup: | 30 mm |
Höjd: | 122 mm |
Snäll: | Voorlicht |
Typ lampa: | LED |
Batterikapacitet: | 2200 mAh |
På / Av knapp: | Ja |
Typ av strömkälla: | Batterij/Accu |
siffra: | 1 |
Lichtstroom: | 450 lm |
Laddning via USB: | Ja |
Väderbeständig: | Ja |
Batteriteknik: | Lithium-Ion (Li-Ion) |
Laddbart batteri: | Ja |
Antal ljuseffekter: | 6 |
Ljuslägen: | Blinking light, Continuous light |
Axelremsmaterial: | Silicone |
Behöver du hjälp?
Om du behöver hjälp med Ultimaker 2+ Connect ställ en fråga nedan och andra användare kommer att svara dig
Skrivare Ultimaker Manualer

9 September 2024

30 Augusti 2024

28 Augusti 2024

20 Augusti 2024
Skrivare Manualer
- Skrivare Sony
- Skrivare Samsung
- Skrivare Xiaomi
- Skrivare LG
- Skrivare Huawei
- Skrivare HP
- Skrivare Panasonic
- Skrivare Epson
- Skrivare Honeywell
- Skrivare Olympus
- Skrivare Toshiba
- Skrivare Xerox
- Skrivare Canon
- Skrivare Brother
- Skrivare Sharp
- Skrivare Renkforce
- Skrivare Kodak
- Skrivare Lenovo
- Skrivare Polaroid
- Skrivare Sagem
- Skrivare Roland
- Skrivare Citizen
- Skrivare Fujifilm
- Skrivare AVM
- Skrivare Konica Minolta
- Skrivare Mitsubishi
- Skrivare Velleman
- Skrivare Seiko
- Skrivare Argox
- Skrivare Oki
- Skrivare Royal Sovereign
- Skrivare Fujitsu
- Skrivare Olympia
- Skrivare Dymo
- Skrivare Bixolon
- Skrivare Ricoh
- Skrivare Lexmark
- Skrivare Dell
- Skrivare Olivetti
- Skrivare Intermec
- Skrivare Zebra
- Skrivare D-Link
- Skrivare Kyocera
- Skrivare Minolta
- Skrivare DNP
- Skrivare GoDEX
- Skrivare Triumph-Adler
- Skrivare Oce
- Skrivare Testo
- Skrivare Metapace
- Skrivare Pantum
- Skrivare Ibm
- Skrivare Tomy
- Skrivare StarTech.com
- Skrivare Toshiba TEC
- Skrivare Frama
- Skrivare Builder
- Skrivare Kogan
- Skrivare Brady
- Skrivare ZKTeco
- Skrivare Star Micronics
- Skrivare Posiflex
- Skrivare Datamax-O'neil
- Skrivare Panduit
- Skrivare Dascom
- Skrivare HiTi
- Skrivare GG Image
- Skrivare Vupoint Solutions
- Skrivare Elite Screens
- Skrivare Primera
- Skrivare DTRONIC
- Skrivare Phoenix Contact
- Skrivare TSC
- Skrivare Star
- Skrivare EC Line
- Skrivare Colop
- Skrivare Equip
- Skrivare Approx
- Skrivare Fichero
- Skrivare Raspberry Pi
- Skrivare Epson 7620
- Skrivare Middle Atlantic
- Skrivare IDP
- Skrivare Evolis
- Skrivare Fargo
- Skrivare Microboards
- Skrivare Tally Dascom
- Skrivare Custom
- Skrivare CSL
- Skrivare Nisca
- Skrivare Sawgrass
Nyaste Skrivare Manualer

16 Januari 2025

16 Januari 2025

15 Januari 2025

15 Januari 2025

15 Januari 2025

15 Januari 2025

15 Januari 2025

15 Januari 2025

15 Januari 2025

15 Januari 2025