Varad IL2W Bruksanvisning

Varad Inte kategoriserad IL2W

Läs nedan 📖 manual på svenska för Varad IL2W (2 sidor) i kategorin Inte kategoriserad. Denna guide var användbar för 2 personer och betygsatt med 4.5 stjärnor i genomsnitt av 2 användare

Ladda ner PDF
Sida 1/2
IL2W
IM-IL2Wv1
Thank you for purchasing the Varad IL2W, dual 1 watt LED
lighting system with driver. To ensure proper use please
carefully read this installation manual prior to installation.
Installation Guide
www.varad.com
1. IL2WC - Digital Controller
2. Two 1 watt LEDs
3. Mounting bracket
4. Power Harness
5. Self tapping screws, 4pcs.
6. flush mount screws, 2pcs.
7. Tie straps, 4 pcs.
Power Harness LEDs
4
4
Digital Controller Description
Technical Specifications
Physical Specifications:
Digital controller:
Height - 0.75”
Width - 1.5”
Length - 2.25”
Current Draw - 250ma
LED:
Length: 3”, Width: 1.25”, Height: 0.55”
Wires:
12’ of cable
Electrical Specifications:
Digital controller:
12v - 24v input
LEDs:
Orange - ALINGAP, 350ma, 180 degree
Red - TS ALINGAP, 350ma, 180 degree
Blue/Green/White - INGAN 350ma, 180 degree
Parts List
Function
These 1 watt LEDs are designed to create accent
lighting for automotive interiors. Applications include,
speaker boxes, footwells, amplifier racks, doors and
much more...
Precautions
To prevent fire or shock hazard, do not expose the
digital controller to rain or moisture.
To avoid electrical shock, do not open the digital
controller. Refer servicing to a factory authorized
dealer. Do not attempt to disassemble the LED or
damage will occur.
Do not bend the wire away from the
bottom of the LED or water may leak
into the housing.
Required tools
· Wire Stripper
· Wire cutter
· Assorted drill dits
· Cordless drill
· Screwdriver
Installation of LEDs
Visually inspect for a location to mount the LED. The
light dispersion pattern will vary depending upon the
location of the LED. It is recommended that you power
up the LED and move it around to determine the
location that provides the best lighting. When you have
found a suitable location, begin to install by marking
each drilling point and pre-drill each hole with a 1/8” drill
bit. Mount the LED with supplied tapping screws. Once
again making an effort not to bend the wire away from
the bottom of the LED, so no damage should occur.
Connect wiring
harness as indicated below:
· Red wire - Battery Positive, 12v - 24v
· Black wire - Negative (Ground)
· Grey wire - refer to installation with
SL200 / SL210 or stand alone
Installation of the Controller
Install the Digital Controller inside the vehicle. Find a
location that will allow all the wires to the LEDs to
connect without binding. The location needs to be with
in 144” of the LED.
Power Harness
4
When all controllers and LEDs are installed you can
proceed to plug all the conectors into the IL2W
controller.
Installation with SL200 / SL210
With the SL200 and SL210
there is an optional LED
expansion port and wire
harness. If you choose, you
can connect the grey
ground trigger wire of the
IL2W to this expansion
connector.
In doing so, this will allow your IL2W to do some of the
same intensity control, strobing, breathing and music
react modes.
Connect wiring
harness as indicated below:
· Red wire - Battery Positive, 12v - 24v
· Black wire - Negative (Ground)
· Grey wire - expansion output on the
SL200, SL210
(NOTE) if using with the expansion output of the SL200
or SL210, Please be aware that the not all strobing and
breathing patterns will function with the IL2W.
Stand alone installation
To install the IL2W in a stand alone application, the grey
ground trigger must be attached to a negative ground
point.
Connect wiring
harness as indicated below:
· Red wire - Battery Positive, 12v - 24v
· Black wire - Negative (Ground)
· Grey wire - Negative (Ground)
Varad's product warranty covers against breakage due to defects in
materials or workmanship for one year from the date of purchase.
Warranty is only valid with proof of purchase from an authorized Varad
dealer. Varad's warranty program does not cover cosmetic damage,
damage due to acts of god, accident, misuse, abuse or negligence to the
product. Repair or replacement as provided under this warranty is the
exclusive remedy of the consumer. Varad shall not be liable for any express
or implied warranty on this product. Except to the extent provided by this
warranty or prohibited by applicable law, there are no implied nor
expressed warranties or merchantability or fitness for a particular
purpose of this product.
www.varad.com
techsupport@varad.com
Designed and Engineered in the U.S.A. Assembled in China
Warranty
Trouble Shooting
System does not turn “ON”
Check to see that the grey wire is grounded or has a
good connection to SL200 or SL210 expansion output.
LED does not work
Check to see that the cable between LED and controller
is not damaged.
Plug into the other port to verify that it is the LED that
is not functioning.

Produktspecifikationer

Varumärke: Varad
Kategori: Inte kategoriserad
Modell: IL2W

Behöver du hjälp?

Om du behöver hjälp med Varad IL2W ställ en fråga nedan och andra användare kommer att svara dig


Inte kategoriserad Varad Manualer

Varad

Varad HLW9 Bruksanvisning

11 September 2024
Varad

Varad SLX300 Bruksanvisning

11 September 2024
Varad

Varad HLW15 Bruksanvisning

11 September 2024
Varad

Varad IL2W Bruksanvisning

11 September 2024

Inte kategoriserad Manualer

Nyaste Inte kategoriserad Manualer

Philips

Philips 43PUL7672 Bruksanvisning

27 Oktober 2024
Manhattan

Manhattan 461504 Bruksanvisning

27 Oktober 2024
Sungrow

Sungrow SG125HV Bruksanvisning

27 Oktober 2024
Schneider

Schneider CCT724319 Bruksanvisning

27 Oktober 2024
Technoline

Technoline WS 250 Bruksanvisning

27 Oktober 2024
Livarno

Livarno IAN 354423 Bruksanvisning

27 Oktober 2024
Kupper

Kupper 12152 Bruksanvisning

27 Oktober 2024
JennAir

JennAir CARBON24L Bruksanvisning

27 Oktober 2024
Medion

Medion Life E74001 (MD 81035) Bruksanvisning

27 Oktober 2024
POLARIS

POLARIS Sportsman Touring 850 SP (2015) Bruksanvisning

27 Oktober 2024