Waste Maid WM-158-3B Bruksanvisning
Waste Maid
soptunna
WM-158-3B
Läs nedan 📖 manual på svenska för Waste Maid WM-158-3B (6 sidor) i kategorin soptunna. Denna guide var användbar för 2 personer och betygsatt med 4.5 stjärnor i genomsnitt av 2 användare
Sida 1/6
Food Waste Disposer
Instruction Manual
See insert for specic information about your new disposer
NOTE: This Food Waste Disposer has been designed to operate on 110-120 Volt, 60 Hz
exclusively. Using any other voltage or Hz adversely affects performance.
IMPORTANT: Read all instructions thoroughly. Keep this guide for future reference.
CAUTION: Be sure to review SAFETY INSTRUCTIONS FIRST PERTAINING TO A RISK OF
FIRE, ELECTRICAL SHOCK OR INJURY TO PERSONS before using disposer.
Record important disposer information here
Model Number* Serial Number*
*Above information appears on the label axed to bottom of the disposer. For your convenience,
write down the model and serial numbers prior to installation.
IMPORTANT SAFETY INSTRUCTIONS
INSTRUCTIONS PERTAINING TO A RISK OF FIRE, ELECTRIC SHOCK OR INJURY TO
PERSONS. SAVE THESE INSTRUCTIONS.
WARNING – When using electrical appliances,
basic precautions should always be followed,
including the following:
1. Read all instructions before using the appliance.
2. To reduce the risk of injury, close supervision is
necessary when an appliance is used near children.
3. Do not put ngers or hands into a waste disposer.
4. Turn the power switch to the o position before
attempting to clear a jam or remove an object from the
disposer.
5. When attempting to loosen a jam in a waste disposer,
use a long wooden object such as a wooden spoon or
the wooden handle of a broom or mop.
6. When attempting to remove objects from a waste
disposer use long-handled tongs or pliers. If the
disposer is magnetically actuated, non-magnetic tools
should be used.
7. To reduce the risk of injury by materials that may be
expelled by a waste disposer, do not put the following
into a disposer: clam or oyster shells; caustic drain
cleaners or similar products; glass, china or plastic;
large whole bones; metal, such as bottle caps, tin
cans, aluminum foil or utensils; hot grease or other
hot liquids; whole cornhusks.
8. When not operating a disposer, leave the stopper in
place to reduce the risk of objects falling into the
disposer.
9. DO NOT operate disposer unless splash guard is in
place.
10. For proper grounding instructions see the ELECTRICAL
CONNECTION portion of this manual.
11. If the supply cord is damaged, it must be replaced by
the manufacturer, its service agent, or authorized
person in order to avoid hazard.
12. This appliance is not intended for use by persons
(including children) with reduced physical, sensory or
mental capabilities, or lack of experience and
knowledge, unless they have been given supervision
or instruction concerning use of the appliance by a
person responsible for their safety.
13. Children should be supervised to ensure that they do
not play with the appliance.
IM-USA-111
If you are utilizing a dishwasher, complete the following
procedure. If dishwasher is not to be connected go on to
section 3.
A. Using a blunt instrument (steel punch or wooden
dowel), knock out entire plug (see 2A). Do not use a
screwdriver or sharp instrument. (When knockout
plug falls into disposer, you may remove it or grind it
up when the disposer is used. This will not damage
the disposer in any way, but may take some time to
grind).
B. Connect dishwasher hose (see 2B) using hose
clamp. Make sure all plumbing connections are tight
and in accordance with all plumbing codes and
ordinances. Run water and check for leaks.
Before starting this step, turn o electrical
power at the circuit breaker or fuse box. Unplug
disposer.
If your old mount is the same type as the mount on your
new disposer, just reverse the assembly instructions found
in section 3. If your new mount system is dierent, follow
these instructions:
A. Use a pipe wrench to disconnect drain line where it
attaches to disposer discharge elbow (see 1A).
B. Remove disposer from sink ange by turning mount
ring to the left clockwise (see 1B). If you are unable to
turn the mount ring, tap on one of the extensions from
the ring with a hammer. Some mounting systems have
tubular extensions. Inserting a screwdriver into one
tube will provide additional leverage for turning the
mount ring (see 1B). Some disposers may require the
removal or loosening of nuts from the mount screws
(see 1C). Some disposers may require the removal of
a clamp.
1. REMOVAL OF OLD UNIT
TYPICAL INSTRUCTIONS, YOUR MODEL MAY VARY.
1A 1B 1C 1D
C. To remove remaining mount system from the sink,
loosen mount screws, push mount ring up. Under it is
the snap ring. Use screwdriver to pop o ring (see
1D). Remove mount ring, protector ring and gasket
from sink flange. Some mounts will require the
unscrewing of a large ring holding the sink ange in
place. Pull sink ange up through sink and clean o
old putty from sink.
IMPORTANT: This is a good time to clean out
the trap and drain lines by running a drain auger
or plumber’s snake before installing your new
disposer.
Caution: Be sure to support the disposer while
performing this step or it may fall when the mounting
ring is disconnected from the mounting assembly.
2. DISHWASHER CONNECTION
KNOCK
OUT PLUG
2B
RUBBER
HOSE
DISHWASHER
HOSE
*
AIR GAP
*Air gap may not be required
for all installations. Check local
plumbing codes.
3. INSTALLATION OF MOUNTING ASSEMBLY
2A
READ COMPLETELY BEFORE STARTING
NOTE: Pay close attention to the order of mount assembly parts, as
they have been correctly assembled by the factory (see 3A). Also,
reference the cushion mount detail in illustration 3G for the proper
position of the cushion mount.
NOTE: Try practicing this assembly before you get under the sink to
get the “feel” of how the parts t together.
A. Disassemble mount assembly from disposer by turning mount
ring to the left (clockwise) and remove.
Speed Master Mount System
SUPPORT RING
CUSHION MOUNT
MOUNT RING
SINK FLANGE
SINK FLANGE
GASKET
DRAIN
DISPOSER
WOOD OR
METAL DOWEL
FIBER GASKET
3A
REMOVABLE SPLASH
GUARD
SPEED MASTER MOUNT SYSTEM
B. Raise mount ring toward top of sink ange. Remove cushion mount.
Remove mount ring. You may want to practice installing the cushion
mount at this point before you are under the sink. See paragraph H.
Also see the “Important Notice: Cushion Mount Detail.”
C. Unscrew support ring from sink ange and remove ber gasket. You
are now left with sink ange and rubber gasket.
D. The rubber gasket is used instead of plumbers putty with stainless
steel sinks. Other sinks will require putty.
E. If no putty is used, insert sink ange through rubber gasket into sink
opening. Do not rotate sink ange once it is seated.
F. If you use putty instead of the gasket, form a ring
around underside of sink ange (see 3D). Insert
flange into sink opening, press down hard to
squeeze out excess putty (see 3B). From under
sink, trim o excess putty ush with bottom edge of
sink opening.
G. From underneath sink, slip ber gasket onto exposed sink ange.
With arrows pointing up, screw support ring onto the sink ange, hand
tighten until the sink ange will not move. At this point you may want
to insert stopper in sink and ll with water to check sink ange seal
and ensure there are no leaks.
H. Place mount ring over sink ange and hold in place while installing
cushion mount (large side down) so the groove on the inside of
cushion mount ts over lip on sink ange, similar to putting the lid on
a plastic container (see 3E, 3F & 3G). Please read important notice
below.
I. The disposer must be installed so that the reset button is readily
accessible.
3C
SINK
FLANGE
SINK
SCREWS
DISCHARGE ELBOW
RUBBER SINK
FLANGE GASKET
(OR PUTTY)
FIBER GASKET
SUPPORT RING
(NOTE ARROWS
INDICATING UP)
REMOVABLE
SPLASH GUARD
MOUNT RING
TIGHTENING EARS
CUSHION MOUNT
GROOVE
ELBOW GASKET
DISHWASHER
INLET
ELBOW
FLANGE
TOP OF SINK FLANGE
FIBER
GASKET
RUBBER
GASKET
SUPPORT
RING
SINK
FLANGE
SINK
BOTTOM
BEAD OF
CUSHION
MOUNT
3F
When the cushion mount is
installed correctly, the lip
of the sink ange ts into
the groove on the inside of
the cushion mount and
mount ring can be pulled
downward over cushion
mount and will be free to
rotate. The bottom bead of
the cushion mount acts as
a gasket between the
bottom of the sink ange
and the top of the disposer.
See illustration 3G.
IMPORTANT NOTICE: CUSHION MOUNT DETAIL
3G
GROOVE
BOTTOM
“LIP” OF
SINK
FLANGE
3E CUSHION MOUNT DETAIL
MOUNT
RING
SUPPORT
RING
3D
SINK
HOPPER
RESET BUTTON
(FRONT)
BOTTOM
BEAD
CUSHION
MOUNT
OPEN AREA, NO
OBSTRUCTION
MOUNT RING
SHOULD BE
FREE TO MOVE
UP & DOWN
3B
A. Connect disposer to appropriate household current
only.
4. ELECTRICAL CONNECTIONS
DANGER: IMPROPER CONNECTION OF THE
EQUIPMENT-GROUNDING CONDUCTOR CAN RESULT
IN A RISK OF ELECTRIC SHOCK. CHECK WITH A
QUALIFIED ELECTRICIAN OR SERVICEMAN IF YOU
ARE IN DOUBT AS TO WHETHER THE APPLIANCE IS
PROPERLY GROUNDED. DO NOT MODIFY THE PLUG
PROVIDED WITH THE APPLIANCE IF IT WILL NOT FIT
THE OUTLET. HAVE A PROPER OUTLET INSTALLED BY
A QUALIFIED ELECTRICIAN.
STOPPER
Produktspecifikationer
| Varumärke: | Waste Maid |
| Kategori: | soptunna |
| Modell: | WM-158-3B |
Behöver du hjälp?
Om du behöver hjälp med Waste Maid WM-158-3B ställ en fråga nedan och andra användare kommer att svara dig
soptunna Waste Maid Manualer
11 December 2024
soptunna Manualer
- soptunna IKEA
- soptunna Gemini
- soptunna Trebs
- soptunna Tower
- soptunna Hobart
- soptunna Turbotronic
- soptunna Suncast
- soptunna SilverSaver
- soptunna Ex-Cell Kaiser
- soptunna Sport-Tronic
- soptunna Joseph Joseph
- soptunna ITouchless
Nyaste soptunna Manualer
5 December 2024
5 December 2024
5 December 2024
5 December 2024
5 December 2024
5 December 2024
5 December 2024
26 September 2024
26 September 2024
26 September 2024