Woods Vacation Villa 2 Bruksanvisning

Woods tält Vacation Villa 2

Läs nedan 📖 manual på svenska för Woods Vacation Villa 2 (2 sidor) i kategorin tält. Denna guide var användbar för 7 personer och betygsatt med 4.5 stjärnor i genomsnitt av 2 användare

Sida 1/2
Woods®
Vacation Villa 2 Room Tent with Awning
PARTS LIST
This tent requires at least three people to assemble.
SET-UP
1. Select a smooth, level site free of debris.
2. Lay out all the poles and sort them into groups
according to the colored stickers affixed to the poles.
3. Create the Roof Structure
Gather the two long pink poles with the attached hubs
and lay them parallel to each other. (NOTE: The one
with the attached four way hub is the pole for the back
of the tent.) Attach the four way front corner hubs (A)
to ends of the front pink stickered pole. Attach the
three way back corner hubs to the ends of the back
pink stickered pole. Put the three yellow stickered
poles into the corresponding stickered yellow hub
openings. Put the blue eave poles into the front hubs
openings. At this point your pole structure should look
like Figure 1.
4. Insert the Leg Poles
Gather together the remaining green and red stickered
poles. The green poles are for the front of the tent and
the red ones are for the back of the tent. Insert them
into the remaining hub openings. At this point your
pole structure should look like Figure 2. (NOTE: we
suggest that two people insert the poles on the diago-
nal of the tent one red and one green to steady the
tent frame structure and the remaining person will
install the other four poles)
5. Insert the Tent Body
The tent can now be attached to the pole structure.
Clip the tent S-Hooks (E) into the six holes in the roof
hubs. Then insert the pin from pin-ring assemblies at
base of tent into ends of poles (F). Then attach the
quick clips to the tent frame (G). As the frame is a free-
standing structure, the tent may be added or removed
as needed.
Qty Description
3 Roof Pole 3 sections 205cm (yellow)
2 Roof Pole with attached hub - 5 sections 335cm (pink)
3 Rear Leg Pole 3 sections 153cm (red)
3 Front Leg Pole 4 sections 224cm (green)
3 Front Eave Pole 1 sections 69cm (blue)
2 Canopy Pole (for end) 3 sections 170cm (black)
1 Canopy Pole (for center) 3 sections 190cm (black)
2 Front Corner 4-way Hub (A)
2 Back Corner 4-way Hub (B)
1 Front Center 5-way Hub (attached to pink pole for front) (C)
1 Rear Center 4-way Hub (attached to pink pole for rear) (D)
3 Bay Window Pre bent Fiberglass pole 3 sections
1 Rainfly/awning
1 Divider Curtain
10 Guy ropes
21 Stakes
1 Pole Storage Bag
1 Stake Storage Bag
1 Tent Storage Bag
6. Install the Bay Windows
Locate the three Pre-bent Fiberglass poles. Slide the
poles through the pole sleeves on the edge of the win-
dow awning. Extend the window awning so it is taut
and then close the nylon fastener flaps to ensure that
the pole remains in position.
7. Stake the Tent Body
To stake out tent drive stakes through webbing loops
attached to pin-ring assemblies (F) at the base of the
tent.
8. Install the rainfly/awning
Lay the fabric of the rainfly over the tent. The edge
with the three grommets (H) should be at the front of
the tent. Attach the five hooks (I) of the fly extensions
that cover the corner and back poles to the holes in
the leg poles Attach the three hooks in the front into.
the ends of the blue poles (J). Wrap the all the nylon
fasteners (K) on the underside of the rainfly around the
poles to further secure the rainfly.
Yellow Sticker Pole
Yellow Sticker Pole
Yellow Sticker Pole
Front of Tent
Blue Sticker Poles
Pink Sticker Pole
Pink Sticker Pole
FIG. 1
Red Rear Leg Pole
Green Front Leg Pole
FIG. 2
FIG. 3
E
A
F
BG
D
A
B
C
JK
H
I
9. Install the poles for the awning
Layout the remaining canopy poles on the ground.
Locate the middle pole (it will be the longest. Put the
metal tip of the canopy pole through the grommet in
the awning (L). While someone is holding the pole
upright, tie one end of the guy rope to the pole tip.
Extend the guy rope so it angles between 1.5 and 2
metres from the pole. Using the slider (M) make a
loop at the end of the rope and insert stake. Repeat
with the other two side poles. Use the slider to adjust
guy rope tension. NOTE: If the awning is not required
it may also be rolled up and tied at the eaves of the
tent.
10. Install the remaining guy ropes of the
rainfly/awning
Locate a guy rope on the side of back of the tent.
Unroll and extend so it angles between 1.5 and 2
metres from the pole. Using the slider (M) make a
loop at the end of the rope and stake to secure.
11. Install the Divider Curtain
To install curtain, push curtain toggles into correspon-
ding loops on inside of tent.
Model 76-5043
Call Toll Free 1 (800) 625-8772 Mon-Fri,
8:00 a.m. to 5:00 p.m. for Bilingual Warranty
Service (Eastern Standard Time)
L
M
TO TAKE DOWN TENT
1. Remove the stakes from base of tent and rainfly
awning. Place in stake bag.
2. Remove and fold divider curtain inside the tent.
3. Remove bay window poles from the three windows.
4. Unhook and remove tent body from frame. Fold into
a rectangle and lay flat.
5. Remove the three front awning poles and guy ropes.
6. Remove rainfly/awning. Fold into thirds to make a
long rectangle and then lay flat.
7. Remove tent poles from hubs and place into pole
storage bag. Put the four hubs into storage bag.
8. Roll tent body and rainfly/awning tightly together.
9. Place tent body, rainfly/awning, pole storage bag,
stake bag into tent carry bag for storage.
The tent frame can be used with or without
the tent body. With the tent body removed, the
rainfly/awning becomes a canopy.

Produktspecifikationer

Varumärke: Woods
Kategori: tält
Modell: Vacation Villa 2

Behöver du hjälp?

Om du behöver hjälp med Woods Vacation Villa 2 ställ en fråga nedan och andra användare kommer att svara dig




tält Woods Manualer

tält Manualer

Nyaste tält Manualer