WyreStorm RX-35 Bruksanvisning

WyreStorm Audio/video-omvandlare RX-35

Läs nedan 📖 manual på svenska för WyreStorm RX-35 (4 sidor) i kategorin Audio/video-omvandlare. Denna guide var användbar för 8 personer och betygsatt med 4.5 stjärnor i genomsnitt av 2 användare

Ladda ner PDF

Sida 1/4

4K UHD HDBaseT™ Receiver with Bidirectional IR,

RS-232 and PoH (4K: 35m/115ft | 1080p: 70m/230ft)

RX-35-POH Quickstart Guide

RX-35-POH Quickstart Guide | 201112

UK: +44 (0) 1793 230 343 | ROW: 844.280.WYRE (9973)

Email: support@wyrestorm.com

1 of 4

WyreStorm recommends reading through this document in its entirety to become familiar with the product’s features before beginning the

installation process.

Basic Wiring Diagram

IMPORTANT! Installation Requirements

• Visit the product page to download the latest rmware, document versions,

additional documentation, and conguration tools.

• Read through the section for important wiring

Wiring and Connections

guidelines before creating or choosing premade cables.

• While this product supports CEC, WyreStorm cannot guarantee

compatibility with all forms of CEC communication.

In the Box

1x RX-35-POH Receiver

1x 12V 2A Power Adaptor (US, UK, EU, AU)

1x IR Emitter

1x IR Receiver

2x Mounting Brackets

1x 3 Pin Phoenix Male Connector

1x Quickstart Guide (this document)

HDR Display

HDMIR RX IR TX

12V DC 2A

Power Supply

RX-35-POH Quickstart Guide | 201112

UK: +44 (0) 1793 230 343 | ROW: 844.280.WYRE (9973)

Email: support@wyrestorm.com

2 of 4

Front Panel Rear Panel

Power LED Solid: The receiver is powered On

Off: The receiver is powered Off

Status LED Flashing: The receiver is operating normally.

Off: The receiver is Not operating normally.

HDCP LED

Solid: HDCP content is present.

Flashing: HDCP content is not present.

Off: No signal.

LINK LED

Solid: Link to receiver has been established.

Flashing: Link to receiver has not been

established.

Power Input

5.5mm Screw Down Barrel Jack

Connect to the included 12V DC 2A power

supply to the transmitter or receiver. A power

supply is not required on the other end as it

will be powered using PoH.

IR TX

IR RX

IR TX - 3.5mm (1/8in) Mono Jack: Connect

to the supplied IR emitter to control a local

device from the remote display location via

HDBaseT

IR RX - 3.5mm (1/8in) Stereo Jack: Connect

to the supplied IR receiver to send IR to the

remote display location via HDBaseT.

See for more

IR TX/RX Guidelines

information.

RS-232 1x RS-232: 3-pin Phoenix

HDBT In

8-pin RJ-45 female

Connect the matrix HDBT Out to

receivers HDBT In.

HDMI Out 19-pin type A HDMI female

Supports HDMI and DVI/D with adapter

A CB D A CB D E

RX-35-POH Quickstart Guide | 201112

UK: +44 (0) 1793 230 343 | ROW: 844.280.WYRE (9973)

Email: support@wyrestorm.com

3 of 4

Wiring and Connections

WyreStorm recommends that all wiring for the installation is run and terminated prior to making connections to the switcher. Read through this section in it’s

entirety before running or terminating the wires to ensure proper operation and to avoid damaging equipment.

IMPORTANT! Wiring Guidelines

• The use of patch panels, wall plates, cable extenders, kinks in cables, and

electrical or environmental interference will have an adverse effect on

signal transmission which may limit performance. Steps should be taken

to minimize or remove these factors completely during installation for best

results.

• WyreStorm recommends the use of shielded category cable to minimize

signal noise and interference.

• WyreStorm recommends using pre-terminated HDMI cables due to the

complexity of these connector types. Using pre-terminated cables will

ensure that these connections are accurate and will not interfere with the

performance of the product.

IR TX/RX Guidelines

• Using WyreStorm infrared emitters and receivers is the best way to ensure

that most IR coding formats are transmitted and received Other 3rd party

emitters and receivers can be used; however, these devices must operate in

the same manner as the WyreStorm devices.

• Due to differences in IR across 3rd party control systems their IR ports

should never be connected directly to a NetworkHD system as an

incompatibility may exist. WyreStorm offers a cable that compensates for

voltage differences as well adjusts for differences in the pins used within

the port. Refer to the product page for more information.

CAB-IR-LINK

IR TX Port Pinout

Connection for IR TX (transmit) uses a 3.5mm (1/8in) mono plug.

Tip: Anode

Sleeve: Cathode (IR Signal)

IR RX Port Pinout

Connection for IR RX (receive) uses a 3.5mm (1/8in) stereo jack that outputs

+5V DC to power the included IR receiver.

Tip:

Ring: IR Signal

+5V DC

Sleeve: Ground (GND)

RS-232 Wiring

The RX-35-POH uses a 3-pin RS-232 with no hardware ow control. Most

control systems and computers are DTE where pin 2 is RX, this can vary

from device to device. Refer to the documentation for the connected device

for pin functionally to ensure that the correct connections can be made.

3rd Party Device

Pin 1 TX (Transmit) > To > RX (Receive)--- ---

Pin 2 RX (Receive) > To > TX (Transmit)--- ---

Pin 3 G (Gro d) > To > G (Gro d)un --- --- un

WyreStorm Co ectornn

Troubleshooting

No or Poor Quality Picture (snow or noisy image)

• Verify that power is being supplied to the transmitter and receiver.

• Verify that the HDBaseT cable is properly terminated following EIA568B

standard.

• Verify that the output resolution of the source and display is supported by

this extender.

• If transmitting 3D or 4K, verify that the HDMI cables used are 3D or 4K rated.

• Verify that all source and HDBaseT connections are not loose and are

functioning properly.

No or Intermittent 3rd party Device Control

• Verify that the RS-232 cables are properly terminated.

• Verify that emitters/receivers are compatible with WyreStorm IR.

• If using an IR control system, verify that it is connected using the CAB-IR-

LINK cable.

Produktspecifikationer

Varumärke:	WyreStorm
Kategori:	Audio/video-omvandlare
Modell:	RX-35
Färg på produkten:	Zwart
Bredd:	483 mm
Djup:	89 mm
Höjd:	44 mm
Förpackningens vikt:	750 g
Förpackningens bredd:	508 mm
Djuppackning:	342.9 mm
Förpackningshöjd:	76.2 mm
Snäll:	Rekschap
Husmaterial:	Staal
Maximal viktkapacitet:	11.34 kg
Hållbarhetscertifikat:	RoHS
Antal per paket:	1 stuk(s)
Rackkapacitet:	1U
Harmoniserad systemkod (HS):	85389099
Monteringshål form:	Ovaal
Kompatibel rackbredd:	19 "
Användbar bredd:	448 mm