Xaoc Katowice Bruksanvisning

Läs nedan 📖 manual på svenska för Xaoc Katowice (6 sidor) i kategorin Inte kategoriserad. Denna guide var användbar för 9 personer och betygsatt med 4.5 stjärnor i genomsnitt av 2 användare

Sida 1/6
stereo
variable band
isolator
Model of 1978
operator’s manual rev. 1978/1.0
Thank you for purchasing this Xaoc Devices
product. Katowice is a stereo variable–band
isolator that allows the user to manipulate

module in a series of upcoming Xaoc Devices

stereo signals.
Katowice splits the stereo input signal into
three bands: low, middle, and high. While
       
frequency and bandwidth of the mid band,
the low and high bands are automatical-
ly adjusted so that the sum of all three is a
complete signal. All three bands are passed
through high quality VCAs and their stereo
outputs are available separately for further
    
available.
Katowice may be used as a crossover net-
 
other band-selective applications, including
multiband compression and stereo enhance-
ment.
The module requires 10hp worth of free
space in the Eurorack cabinet. The rib-
bon-type power cable must be plugged into
the bus board, paying close attention to po-
larity orientation. The red stripe indicates
the –12V rail and should point in the same
direction on both the bus board and the unit.
The module itself is secured against reversed
power connection, however, reversing the
16-pin header may cause serious damage
to other components of your system because
it will short-circuit the +12V and +5V power
rails.
The module should be fastened by mounting
the supplied screws before powering up. To
better understand the device, we strongly
advise the user to read through the entire
manual before using the module.

The stereo pair of signal inputs is
AC-coupled and accepts all Eurorack signal
levels (up to 20Vpp), however, a conservative
-
ing certain signals may occasionally result
in increased amplitude and cause distortion.
   
the position of the two knobs: mid freq
sets the geometric center of the middle band
(in Hz), and mid width sets the width of
this band (in octaves). The corresponding
two jacks and allow for voltage control
and accept voltages in ±5V range. The ampli-
tude of the middle band is controlled by the
central mid slider and the corresponding
CV input above that accepts voltages in
the range of ±8V. The left slider low and
CV input control the amplitude of low fre-
module
explained
front panel
overview
fig. 1: interface

Produktspecifikationer

Varumärke: Xaoc
Kategori: Inte kategoriserad
Modell: Katowice

Behöver du hjälp?

Om du behöver hjälp med Xaoc Katowice ställ en fråga nedan och andra användare kommer att svara dig




Inte kategoriserad Xaoc Manualer

Xaoc

Xaoc Ustka 1966 Bruksanvisning

26 September 2024
Xaoc

Xaoc Batumi Bruksanvisning

11 September 2024
Xaoc

Xaoc Poti Bruksanvisning

11 September 2024
Xaoc

Xaoc Zadar Bruksanvisning

11 September 2024
Xaoc

Xaoc Katowice Bruksanvisning

11 September 2024
Xaoc

Xaoc Tirana Bruksanvisning

11 September 2024
Xaoc

Xaoc Warna II Bruksanvisning

11 September 2024
Xaoc

Xaoc DEVA Bruksanvisning

11 September 2024
Xaoc

Xaoc Lipsk Bruksanvisning

11 September 2024

Inte kategoriserad Manualer

Nyaste Inte kategoriserad Manualer