Air King EWF-180 Bruksanvisning

Air King Fläkt EWF-180

Läs nedan 📖 manual på svenska för Air King EWF-180 (8 sidor) i kategorin Fläkt. Denna guide var användbar för 2 personer och betygsatt med 4.5 stjärnor i genomsnitt av 2 användare

Ladda ner PDF

Sida 1/8

IMPORTANT INSTRUCTIONS -

OPERATING MANUAL

SAVE THESE INSTRUCTIONS

www.airkinglimited.com

210575005 Rev. D 12-15 1 of 8

Through the Wall Exhaust Fan

Model: EWF-180

READ AND SAVE THESE INSTRUCTIONS

READ CAREFULLY BEFORE ATTEMPTING TO ASSEMBLE, INSTALL, OPERATE OR MAINTAIN

THE PRODUCT DESCRIBED. PROTECT YOURSELF AND OTHERS BY OBSERVING ALL SAFETY

INFORMATION. FAILURE TO COMPLY WITH INSTRUCTIONS COULD RESULT IN PERSONAL

INJURY AND/OR PROPERTY DAMAGE!

RETAIN INSTRUCTIONS FOR FUTURE REFERENCE.

GENERAL SAFETY INFORMATION

When using electrical appliances, basic precautions should

always be followed to reduce the risk of ﬁre, electric shock and

injury to person, including the following:

WARNING: TO REDUCE THE RISK

OF FIRE, ELECTRIC SHOCK AND INJURY TO

PERSON, OBSERVE THE FOLLOWING:

a) Use this unit only in the manner intended by the manufacturer.If you have

questions, contact the manufacturer.

b) Before servicing or cleaning the unit, switch power off at service

panel and lock the service disconnecting means to prevent power

from being switched on accidentally. When the service disconnecting

means cannot be locked, securely fasten a prominent warning

device, such as a tag, to the service panel.

WARNING: TO REDUCE THE RISK

OF FIRE, ELECTRIC SHOCK AND INJURY TO

PERSON, OBSERVE THE FOLLOWING:

a) Installation work and electrical wiring must be done by qualiﬁed

person(s) in accordance with all applicable codes and standards,

including ﬁre-related construction.

b) Sufﬁcient air is needed for proper combustion and exhausting of

gases through the ﬂue (chimney) of fuel burning equipment to prevent

back drafting. Follow the heating equipment manufacturer’s guideline

and safety standards such as those published by the National Fire

Protection Association (NFPA) and the American Society for Heating,

Refrigeration, and Air Conditioning Engineers (ASHRAE), and the local

code authorities.

c) When cutting or drilling into wall or ceiling, do not damage electrical

wiring and other hidden utilities.

CAUTION: FOR GENERAL VENTILATING USE ONLY.

DO NOT USE TO EXHAUST HAZARDOUS OR EXPLOSIVE

MATERIALS AND VAPORS.

d) Ducted fans must always be vented to the outdoors.

e) This unit must be grounded.

f) To avoid motor bearing damage and noisy and/or unbalanced impellers,

keep drywall spray, construction dust, etc. off power unit.

g) Read all instructions before installing or using exhaust fan.

WARNING: TO REDUCE THE RISK OF FIRE,

ELECTRIC SHOCK, DO NOT USE THIS FAN WITH

ANY SOLID-STATE SPEED CONTROL DEVICE.

a) If this unit is to be installed over a tub or shower, it must be

marked as appropriate for the application and be connected to a

GFCI (Ground Fault Circuit Interrupter) – protected branch circuit.

WARNING: DO NOT USE IN KITCHENS.

INSTALLATION INSTRUCTIONS

CAUTION: MAKE SURE POWER IS SWITCHED OFF AT

SERVICE PANEL BEFORE STARTING INSTALLATION.

SECTION 1

Preparing the Exhaust Fan

1. Unpack from carton and conﬁrm that all pieces are present. You should have:

1 - Grill

1 - Grill Knob

1 - Wiring Compartment and screws

1 - Motor

1 - Housing

1 - Instruction/Safety Sheet

NOTE: This fan is designed to mount between exterior walls 4-1/2” to 9-1/2” in thickness.

2. Remove the motor bracket assembly from the fan housing by loosening the two screws

which secure the bracket in place .(Figure 1)

3. Slide the inner housing out from the outer housing and set aside in a safe place (Figure 2).

SECTION 2

Mounting the Housing

1. From inside the house, choose the best location to mount the housing on an exterior wall.

Make sure to locate the housing where there are no studs, electrical/mechanical utilities,

or any other obstructions.

2. Once you have selected the best location from inside the house, transfer the location to

the exterior of the house and conﬁrm that there are no obstructions in the location and

the fan has proper clearance to operate.

3. Once the installation location has been conﬁrmed, cut a 8-1/4” diameter hole in the

interior wall where the fan is to be located (Figure 3).

4. Drill a small hole through to the outside in the center of the 8-1/4” diameter hole, so you

can properly locate the exterior housing (Figure 3).

www.airkinglimited.com

210575005 Rev. D 12-15 2 of 8

5. On the siding of the outside wall, layout a 14-1/2” x 14-1/2” square using the small hole

drilled in Step 4 as the center point and cut out the square hole (Figure 4).

CAUTION: ONLY CUT THE EXTERIOR WALL SIDING. DO NOT CUT INTO

THE SHEATHING (PLYWOOD) UNDERNEATH.

6. Once the siding is cut, nail down all the loose ends of the siding (Figure 4).

7. In the center of the 14-1/2” square cut in step 5, mark and cut a 8-1/4” diameter hole

through the wall sheathing (Figure 5).

8. Install 1” x 2” casing strips (not included) for support on the edges of the 14-1/2” square

hole. Secure casing strips to plywood sheathing with screws or nails (not included) and

seal where the strips meet the plywood with caulk (Figure 5).

CAUTION: IF SHEATHING IS NOT PLYWOOD, YOU WILL HAVE TO ADD

ADDITIONAL SUPPORT FOR THE INSTALLATION.

9. If the wall is less than 8” thick, remove one or more of the electrical compartment

clearance knockouts located on the housing (Figure 6).

10. On the interior ﬂange of the housing, apply a generous amount of caulking and install the

housing through the hole and onto the casing strips and secure in place using screws or

nails (not included) through the predrilled holes on the four corners of the housing. Seal

the ﬂange where the housing meets the wall with caulk (Figure 7).

Figure 1

Screws

Figure 2

Inner

Housing

Outer

Housing

Figure 3

Exterior

Wall

Interior

Wall

Exterior

Wall Interior

Wall

Hole

Figure 4

Nail

14½"

Figure 5

8¼"Casing

Knockouts

Figure 6

Figure 7

Screw Caulk

SECTION 3

Wiring

CAUTION: MAKE SURE POWER IS SWITCHED OFF AT

SERVICE PANEL BEFORE STARTING INSTALLATION.

CAUTION: ALL ELECTRICAL CONNECTIONS MUST BE MADE

IN ACCORDANCE WITH LOCAL CODES, ORDINANCES, OR NATIONAL

ELECTRICAL CODE. IF YOU ARE UNFAMILIAR WITH METHODS OF INSTALLING ELECTRICAL

WIRING, SECURE THE SERVICES OF A QUALIFIED ELECTRICIAN.

1. Run wiring from an approved wall switch carrying the appropriate rating. One neutral

(white), one ground (green or bare copper), and one hot (black).

2. From inside the house, insert the inner housing into the outer housing until it is tight against

the wall. Line up three holes at the end of the inner housing with three of the holes on the

outer housing and secure in place with the three included 3/8” screws (Figure 8).

NOTE: If you removed any of the electrical compartment clearance knockouts on the outer

housing, make sure the electrical opening of the inner housing is aligned with them.

3. Pull the electrical wires through the electrical opening of the interior housing. Remove one

of the electrical knockouts of the wiring compartment and run wires through the opening

making sure to leave enough wiring to make the connection to the fan’s receptacle. Secure

wires to wiring compartment with an approved electrical connector (Figure 9).

4. Connect the green or bare ground wire from the house to the ground screw in the

wire compartment. Connect the white wire from the house to the white wire from the

receptacle. Connect the hot (black) wire from the wall switch to the black wire from the

receptacle Use approved methods for all connections. (Figure 10).

5. Insert the wire compartment into the electrical opening of the interior housing and line

up holes of wire compartment and wire compartment cover with holes on the interior

housing. Secure in place using the two included 1/2” screws (Figure 11).

www.airkinglimited.com

210575005 Rev. D 12-15 3 of 8

SECTION 4

Completing the Installation

1. Reinstall the fan’s motor bracket by sliding in place and tightening the screws. Rotate

the blower wheel by hand to ensure it spins freely. Now plug the fan motor into the

receptacle (Figure 1).

2. Install grill by positioning over the inner housing and aligning the center hole on the grill

with the hole on the motor bracket. Screw one side of the included grill bolt into the hole

on the motor bracket and the other side into the grill knob and turn to tighten until the

grill is tightly ﬁt against the wall. DO NOT OVER TIGHTEN (Figure 12).

3. Restore power and test your installation.

SECTION 5

Use and Care

CAUTION: MAKE SURE POWER IS SWITCHED OFF AT

SERVICE PANEL BEFORE SERVICING THE UNIT.

1. Cleaning the Grill: Remove grill and use a mild detergent, such as dishwashing liquid,

and dry with a soft cloth. NEVER USE ANY ABRASIVE PADS OR SCOURING POWDERS.

Completely dry grill before reinstalling. Refer to instructions in Section 4 Completing the

Installation, to reinstall grill.

2. Cleaning the Fan Assembly: Wipe all parts with a dry cloth or gently vacuum the fan.

NEVER IMMERSE ELECTRICAL PARTS IN WATER.

CALIFORNIA RESIDENTS ONLY:

WARNING: THIS PRODUCT CAN EXPOSE YOU TO A CHEMICAL [OR

CHEMICALS] KNOWN TO THE STATE OF CALIFORNIA TO CAUSE CANCER.

WARNING: THIS PRODUCT CAN EXPOSE YOU TO A CHEMICAL [OR

CHEMICALS] KNOWN TO THE STATE OF CALIFORNIA TO CAUSE REPRODUCTIVE

TOXICITY.

Figure 8

Hole

Knockout

Inner

Housing

Electrical

Opening

Figure 10

Figure 9

Knockout

Electrical

Opening

Wiring Compartment

Figure 11

Electrical Opening

Wiring Compartment Cover

Wiring Compartment

Figure 12

Grill

Bolt

Grill

Knob

Motor

Bracket Hole

Produktspecifikationer

Varumärke:	Air King
Kategori:	Fläkt
Modell:	EWF-180
Färg på produkten:	Zwart
Förpackningens vikt:	7000 g
Användarmanual:	Ja
Justerbar i höjdled:	Ja
Beeldscherm:	LCD
Skärm diagonal:	24 "
Upplösning:	1920 x 1080 Pixels
Pekskärm:	Nee
Original bildförhållande:	16:9
Typ av anslutningskontakt:	3,5 mm
Videolägen som stöds:	1080p
Betraktningsvinkel, horisontell:	178 °
Betraktningsvinkel, vertikal:	178 °
Medföljande kablar:	AC, Audio (3.5mm), DisplayPort, VGA
Typiskt kontrastförhållande:	1000:1
VGA (D-Sub) port(ar):	2
Antal HDMI-portar:	2
Monteringsalternativ för kabellås:	Ja
Kabellåsspårtyp:	Kensington
Inbyggda högtalare:	Ja
Genomsnittlig effekt:	2 W
Strömförbrukning (i standby):	0.5 W
Antal högtalare:	2
Hörlursutgångar:	1
Certifiering:	FCC-B, CE, UL/cUL, RoHS
Display, antal färger:	16.78 miljoen kleuren
HDCP:	Ja
Maximal uppdateringshastighet:	76 Hz
HD typ:	Full HD
Ljudingångar:	Ja
Displayteknik:	LED
Respons tid:	5 ms
Pixelpitch:	0.2715 x 0.2715 mm
Grafikupplösningar som stöds:	1920 x 1080 (HD 1080)
VESA montering:	Ja
Panelmonteringsgränssnitt:	100 x 100 mm
Ljusstyrka (typiskt):	250 cd/m²
Djup (utan bas):	53.3 mm
Höjd (utan bas):	332.7 mm
Bredd (utan bas):	561.3 mm
Vikt (utan bas):	3700 g
Antal DisplayPorts:	2
Enhetsbredd (med stativ):	561.3 mm
Djupenhet (med stativ):	213.4 mm
Enhetshöjd (med stativ):	386.1 mm
Vikt (med stativ):	5700 g
On Screen Display (OSD):	Ja
Typ av bakgrundsbelysning:	Edge LED
Typ av panel:	IPS
Roterbar:	Ja
Horisontellt vridbar:	45 - 45 °
Mac-kompatibilitet:	Ja
Bildområde:	Glans
Fötter färg:	Zwart
Gångjärn:	Ja
Pivothörn:	0 - 90 °
AC-ingångsspänning:	100 - 240 V
Strömförbrukning (typiskt):	32 W
Tiltvinkelområde:	-5 - 15 °
lutningsjusteringar:	Ja