Aurum TITAN VII Bruksanvisning

Aurum högtalare TITAN VII

Läs nedan 📖 manual på svenska för Aurum TITAN VII (21 sidor) i kategorin högtalare. Denna guide var användbar för 9 personer och betygsatt med 4.5 stjärnor i genomsnitt av 2 användare

Sida 1/21
USER INSTRUCTIONS
BEDIENUNGSANLEITUNG
NOTICE D´UTILISATION
MANUAL DE INSTRUCCIONES
TITAN VII
VULKAN VII
MONTAN VII
ESPAÑOL
FRANÇAIS
DEUTSCH
ENGLISH
BDA AURUM 22.08.06.indd 1 19.09.2006 12:07:50 Uhr
2
ENGLISH
3
Contents/Inhalt/Sommaire/Índice
Safety notes 3-4
Setting up 5
Positioning your speaker on hard floor surface 5-6
Connecting to the amplifier 6-8
Beware of clipping 9
Care of loudspeakers 9
What to do if your speakers don‘t sound right ? 10
Technical data 11
Sicherheitshinweise 12-13
Aufstellung 14
Platzierung auf harten Böden 14-15
Anschluss an den Verstärker 15-17
Vorsicht Clipping 18
Pflege der Lautsprecher 18
Was tun in Störungsfällen? 19
Technische Daten 20
Sécurité 21-22
Installation 23
Placement sur des sols durs 23-24
Raccordement á l‘amplificateur 24-26
Attention, risque de distorsion 27
Entretien des enceintes 27
Que faire en cas d’anomalies ? 28
Caratéristiques techniques 29
Seguridad 30-31
Ubicación 32
Colocación en suelo duro 32-33
Conexión al amplificador 33-35
Cuidado Clipping 36
Mantenimiento de los altavoces 36
¿Qué hacer en caso de avería? 37
Datos técnicos 38
First of all, thank you for deciding on AURUM loudspeakers.
It is to satisfy the high expectations of music lovers and connoisseurs such as you that
we build loudspeakers of a class that is well above average. Even though you may
already be familiar with them, we list below a few ground rules that will enable you
to make optimal use of your loudspeakers.
Safety advice for passive loudspeakers
Please take time to read through the manual carefully and follow all the steps
describing how to set up and operate the loudspeakers. Keep the manual
somewhere you can quickly access it should you have any questions later on.
The stability of loudspeakers (especially large units) depends on the nature of
the surface on which they stand. Carpets are often very poor for stability. Even an
average bump can cause a loudspeaker to fall over and be a hazard for persons
or pets in the vicinity. Stability can be significantly improved by using “spikes”, but
care should be taken during assembly as the sharp points can cause injury and
the spikes can damage the floor. On smooth floors, the loudspeakers can be
stabilised with Velcro or double-sided tape. Loudspeakers should never be used
as a seat or as a substitute for a ladder!
Use only wheeled furniture, stands or wall mounting systems and other devices for
attaching and installing the products, which are available from the manufacturer
and are sold for or with the product. To avoid damage or injury through tipping
over, please be careful when moving table devices or stands on which the
speakers are mounted. If wall-mounting the product, take special care that all
components are securely screwed! Additional securing equipment (chains, etc.)
should be fitted.
The location for the loudspeakers should be dry and not too cold. Constant high
humidity or strong sunlight (UV radiation) can cause your loudspeakers to age
prematurely and consequently affect their functioning.
Very high volume levels for long periods of time are not only annoying for your
neighbours, but can also be harmful to the health of the user!
When loudspeakers are overloaded with very high volume levels, there is a risk
of individual components in crossover circuits or individual speakers burning out.
In particularly bad cases, it is even possible for fire to break out inside a speaker.
Speakers operated at these extremes should therefore not be left unattended.
FRANÇAIS
ESPAÑOL
DEUTSCH
BDA AURUM 22.08.06.indd 2-3 19.09.2006 12:07:51 Uhr
4
ENGLISH
5
Setting up
As a rule you should try various set-up positions in order to get the best sound
results.
Since the positioning of loudspeakers decisively influences the quality of the sound
they deliver, we’ll start by giving you some hints on how and where to set your
AURUM units up.
Placing the speakers near the corners of the room will essentially give you loud
bass reproduction but with little outline. On the other hand, speakers positioned well
away from the walls sound precise, but also very bright and thin. The best solution is
to place the speakers with a clearance of at least 30 cm between their backs and
the nearest wall. To avoid loud wall reflections, the distance from the side walls of the
room can even be 50 cm or more.
As far as possible, the speakers should be equidistant from the listening position, while
the distance of the speakers from each other can be rather less than the distance
from the listener.
Positioning your speakers on hard floor surfaces
If your AURUM floorstanding speakers are going to be placed on a hard floor
surface, for instance on tiles, stone, parquet or laminate, we urgently recommend
that you fit the supplied rubber mats in place under the cabinet base. These mats
will protect your speakers as well as the floor from damage while compensating
any slightly uneven spots. However, you will not need to use them where soft
floor surfaces such as carpets are concerned since the aluminium discs pre-fitted
between the cabinet and base already serve the purposes of acoustic decoupling.
When fitting the rubber mats (S) onto the speaker base you will need a helper as
well as the cardboard angle strip that you will find in the speaker
packaging. We recommend doing so on each of the speakers
as follows:
Firstly, determine where you definitively wish to position the
speaker in the listening area and have the angle strip and
rubber mat ready to hand.
Your helper should now tilt the cabinet slightly to one side
so that you can slide the angle strip one centimetre (at the
most!) under the raised edge of the cabinet base.
Your helper should now tilt the cabinet slightly to the other
side and hold it in this tilted position while you fit the rubber
mat precisely into place under the raised base; when doing
At high volumes, voltage levels of 30–50 V can be present at speaker terminals
and components. Be very careful not to touch uninsulated terminal contacts of
speakers when in operation. To avoid injury, never put hands or arms into sound
outlets (bass reflex tubes). Children and pets, in particular, are at risk from this.
For safety reasons, we generally forbid the opening of loudspeaker cabinets
when in operation or connected since, as explained in the above paragraph,
voltages of up to 50 volts can be present inside.
Improper handling of mains voltage can cause fatal injury!
Passive loudspeakers must on no account be connected to the electricity
supply!
Speaker terminals may only be connected to the appropriate output terminals
of the amplifier. You should never connect these terminals to the electricity supply
(230 V/115 V) in any way since that will otherwise also immediately destroy the
loudspeaker and all connected products. Avoid fitting plugs to ends of speaker
cables that could even remotely be confused with mains supply plugs.
Loudspeakers that are not magnetically shielded can affect the colour of the
TV picture or cause distortion. A distance of 50 cm is generally sufficient to avoid
problems of this kind. Avoid placing items such as credit cards, diskettes, audio or
video cassettes or other magnetic media on the loudspeaker. This could destroy
the information stored on them. Similarly, avoid operating magnetic tape devices
in the immediate vicinity.
(W )
BDA AURUM 22.08.06.indd 4-5 19.09.2006 12:07:52 Uhr

Produktspecifikationer

Varumärke: Aurum
Kategori: högtalare
Modell: TITAN VII

Behöver du hjälp?

Om du behöver hjälp med Aurum TITAN VII ställ en fråga nedan och andra användare kommer att svara dig




högtalare Aurum Manualer

högtalare Manualer

Nyaste högtalare Manualer