BeamZ F1500 160.510 Bruksanvisning
Läs nedan 📖 manual på svenska för BeamZ F1500 160.510 (46 sidor) i kategorin Vi. Denna guide var användbar för 4 personer och betygsatt med 4.5 stjärnor i genomsnitt av 2 användare
Sida 1/46
Ref. Nr. 160.510
F1500
Fazer with DMX & Controller
INSTRUCTION MANUAL
GEBRUIKSAANWIJZING
BEDIENUNGSANLEITUNG
V1.1
- 2 -
Warning:
- The fazermachine must be placed at least 100 cm away from inflammable materials such as curtains, books,
etc. Make sure that the housing cannot be touched by accident.
- Use only Beamz water-based fluid recommended by your dealer.
- Poor liquid caused permanent damage, bad effect, clogging, spitting of unevaporated liquid etc.
- Never add flammable fluids (oil, gas, perfume) to the fog liquid.
- Always keep enough liquid in the tank.
Use of the device without liquid will cause damage to the pump and heater.
- Do not obstruct the openings on top of the case to guarantee a good ventilation.
- Don’t put any objects on the fazer machine.
- For indoor use only.
- During installation, nobody should stand beneath the mounting area.
- Prior to the first use, have the unit checked by a qualified person.
- The unit contains voltage carrying parts. DO NOT open the fazermachine
- Never plug or unplug the unit with wet hands.
- If the plug and/or mains lead are damaged, they need to be repaired by a qualified technician.
- If the unit is damaged to an extent that you can see internal parts, do not plug the unit into a mains outlet. It
needs to be repaired by a qualified technician.
- Only connect this unit to an earthed mains outlet of 220-240Vac/50Hz .
- Always unplug the unit during a thunderstorm or when it is not in use.
- If the unit has not been used for a longer period of time, condensation can occur inside the housing. Please
let the unit reach room temperature prior to use.
- When you unplug the unit from the mains always pull the plug, never the lead.
- In order to prevent dropping of the unit, a safety fastening needs to be installed. This can be a solid chain, a
steel cable, etc. which has to be fastened separately from the mounting bracket.
- The supplied bracket is the main fixing and must be used to solidly mount the light effect.
- In order to avoid accidents in public premises, the local legal requirements and safety regulations/warnings
must be fulfilled.
- Keep out of the reach of children.
Location
Select a location where it is easy to fill the tank. It is also possible to hang the unit by means of the supplied
holder and fixing screws.
Installation and Use
Unpack the fazer machine. Do not connect yet the net cable. Connect the remote control to the connector on
the back of the fogger.Fill the fluid tank by means of a funnel. Plug the unit into a mains outlet. Thus the heating
element is automatically switched on. Depending on the room temperature, it takes about 4 minutes until the
working temperature is reached. Then the thermostat is clicking and the LED on the manual control lights up.
Push the switch once and the fazer machine will produce a nice thick fog. Once the fazer machine has reached
its working temperature (the LED is lit) the fazer machine can produce fog continuously. After this period of time,
the fog generator is cooled so much down that the thermostat switches off. Wait a while until the working
temperature is reached again. It is recommended to produce haze with small pauses in between so that the
temperature is maintained and the thermostat doesn’t switch off.
Make sure that there is always enough liquid contained r machine without liquid can in the tank. Use of the faze
permanently damage the unit. Once the fazer machine generates little haze or pump generate another 'rattling'
sound i turn off the unit direct. Check the fluid level and fill the tank when it is empty, check the hose and filter
blockages and restore it. Plug in the unit and check if the problem is resolved. If problem persists, switch unit
direct off to prevent further damage and contact your dealer.
Switching the unit off
Switch the unit off by unplugging it from the mains. Otherwise the 1500W heating element will draw
unnecessarily current.
- 3 -
Timer remote control
Connect the remote control to the connector on the back of the fogger.
After some warm-up time, the device is ready for use, the LED will light up on the remote. During use, it may
happen that the machine stops, in this case the LED will go out, indicating that the machine is warming up.
Timer function:
Press the yellow button and set the interval, duration and volume controls to the desired level.
Interval: time between the smoke moments (10-200 seconds)
Volume: amount of smoke (0-100%)
Duration: duration of the smoking time
Continuous function:
Press the red button and set the volume to the desired level. The machine will continueously produce an
amount of smoke. It may be that the machine in between have to warm up, during this period no smoke is
produced. How many times this is done depends on the amount of smoke.
Manual Mode:
Press the green button to produce 100% smoke immediately; this button overrides all previous settings.
DMX control (DIP)
Connect the device directly to a DMX controller or a DMX loop with multiple DMX effects. The machine has a 3-
pin XLR connector for DMX connection.
Address Setup:
Use the DIP switch on the rear panel to set the start address. The base/start address is defined as a first
channel, where responsive to the device. Check if no overlapping channels are used!
Example addressing:
DMX
address
Dipswitch
1
2
3
4
5
Etc.
Note:
It is necessary always lock a DMX loop with a 120 Ohm terminator for correct data
transmission.
CHANNEL VALUE FUNCTION
1 0 – 100% Smoke level
Produktspecifikationer
| Varumärke: | BeamZ |
| Kategori: | Vi |
| Modell: | F1500 160.510 |
Behöver du hjälp?
Om du behöver hjälp med BeamZ F1500 160.510 ställ en fråga nedan och andra användare kommer att svara dig
Vi BeamZ Manualer
17 Oktober 2024
2 Oktober 2024
11 Augusti 2024
8 Augusti 2024
3 Augusti 2024
Vi Manualer
- Vi IKEA
- Vi Severin
- Vi Black And Decker
- Vi Tristar
- Vi Waring Commercial
- Vi Livoo
- Vi Crivit
- Vi Bestron
- Vi Ryobi
- Vi Clatronic
- Vi Russell Hobbs
- Vi Ernesto
- Vi Hazet
- Vi Hama
- Vi Exquisit
- Vi Hamilton Beach
- Vi Primo
- Vi Gastroback
- Vi Team
- Vi G3 Ferrari
- Vi Wolf
- Vi N8WERK
- Vi Toolcraft
- Vi Kalorik
- Vi Karma
- Vi Girmi
- Vi Underwater Kinetics
- Vi Brentwood
Nyaste Vi Manualer
3 Oktober 2024
2 Oktober 2024
30 September 2024
29 September 2024
26 September 2024
26 September 2024
26 September 2024
26 September 2024
24 September 2024
23 September 2024