BeamZ S700 160.438 Bruksanvisning

BeamZ Vi S700 160.438

Läs nedan 📖 manual på svenska för BeamZ S700 160.438 (12 sidor) i kategorin Vi. Denna guide var användbar för 9 personer och betygsatt med 4.5 stjärnor i genomsnitt av 2 användare

Ladda ner PDF

Sida 1/12

Ref. Nr. 160.438

S700

SMOKE MACHINE

INSTRUCTION MANUAL

GEBRUIKSAANWIJZING

BEDIENUNGSANLEITUNG

V1.1

- 2 -

- 3 -

Warning:

- The smokemachine must be placed at least 100 cm away from inflammable materials such as curtains,

books, etc. Make sure that the housing cannot be touched by accident.

- Use only Beamz water-based smoke fluid recommended by your dealer.

- Poor smoke liquid caused permanent damage, bad effect, clogging, spitting of unevaporated liquid etc.

- Never add flammable fluids (oil, gas, perfume) to the fog liquid.

- Always keep enough smoke liquid in the tank.

Use of the device without liquid will cause damage to the pump and heater.

- Do not obstruct the openings on top of the case to guarantee a good ventilation.

- Don’t put any objects on the smoke machine.

- For indoor use only.

- During installation, nobody should stand beneath the mounting area.

- Prior to the first use, have the unit checked by a qualiﬁed person.

- The unit contains voltage carrying parts. DO NOT open the smokemachine

- Never plug or unplug the unit with wet hands.

- If the plug and/or mains lead are damaged, they need to be repaired by a qualified technician.

- If the unit is damaged to an extent that you can see internal parts, do not plug the unit into a mains outlet. It

needs to be repaired by a qualiﬁed technician.

- Only connect this unit to an earthed mains outlet of 220-240Vac/50Hz .

- Always unplug the unit during a thunderstorm or when it is not in use.

- If the unit has not been used for a longer period of time, condensation can occur inside the housing. Please

let the unit reach room temperature prior to use.

- When you unplug the unit from the mains always pull the plug, never the lead.

- In order to prevent dropping of the unit, a safety fastening needs to be installed. This can be a solid chain, a

steel cable, etc. which has to be fastened separately from the mounting bracket.

- The supplied bracket is the main fixing and must be used to solidly mount the light effect.

- In order to avoid accidents in public premises, the local legal requirements and safety regulations/warnings

must be fulfilled.

- Keep out of the reach of children.

Location

Select a location where it is easy to fill the tank. It is also possible to hang the unit by means of the supplied

holder and fixing screws.

Installation and Use

Unpack the fog machine. Fill the fluid tank by means of a funnel. Plug the unit into a mains outlet. Thus the

heating element is automatically switched on. Depending on the room temperature, it takes about 2 minutes

until the working temperature is reached. Then the thermostat is clicking and the LED on the manual control

lights up. Push the switch once and the smoke machine will produce a nice thick fog. Once the smoke machine

has reached its working temperature (the LED is lit) the smoke machine can produce fog for a while. After this

period of time, the fog generator is cooled so much down that the thermostat switches off. Wait a while until the

working temperature is reached again. It is recommended to produce smoke with small pauses in between so

that the temperature is maintained and the thermostat doesn’t switch off.

Make sure that there is always enough liquid smoke contained in the tank. Use of the smoke machine without

liquid can permanently damage the unit. Once the smoke machine generates little smoke or pump generate

another 'rattling' sound i turn off the unit direct. Check the fluid level and fill the tank when it is empty, check the

hose and filter blockages and restore it. Plug in the unit and check if the problem is resolved. If problem persists,

switch unit direct off to prevent further damage and contact your dealer.

Switching the unit off

Switch the unit off by unplugging it from the mains. Otherwise the 700W heating element will draw unnecessarily

current.

Produktspecifikationer

Varumärke:	BeamZ
Kategori:	Vi
Modell:	S700 160.438
Färg på produkten:	Zwart
Vikt:	15100 g
Original bildförhållande:	4:3
Synlig skärmhöjd (h):	1097.28 mm
Synlig skärmbredd (b):	1463.04 mm
Diagonal:	72 "
Schermgain:	1.1