Crestron GLS-PART-CN Bruksanvisning

Crestron Smarth hem GLS-PART-CN

Läs nedan 📖 manual på svenska för Crestron GLS-PART-CN (2 sidor) i kategorin Smarth hem. Denna guide var användbar för 12 personer och betygsatt med 4.5 stjärnor i genomsnitt av 2 användare

Ladda ner PDF

Sida 1/2

GLS-PART-CN

Cresnet® Partition Sensor

Installation and Operation Guide

Description

The Crestron® GLS-PART-CN is a partition sensor that is controlled by the Cresnet

network and designed for installation into a 1-gang electrical box or surface mounting. The

GLS-PART-CN has a contact closure output (EXT) that allows for use in a non-system

environment.

Installation

NOTE: Observe the following points:

• Install and use this product in accordance with appropriate electrical codes and

regulations.

• If you are unsure about any part of these instructions, consult a qualied electrician.

• Sensors must be mounted on a vibration-free surface.

NOTE: Before using the GLS-PART-CN, ensure the device is using the latest rmware.

Check for the latest rmware for the GLS-PART-CN at www.crestron.com/rmware.

Load the rmware onto the device using Crestron Toolbox™ software.

Preparing and Connecting Wires

When making connections, strip the ends of the wires approximately 7/16 in (11 mm). Use

care to avoid nicking the conductors. Tighten the connector to 5 in-lb (0.5 to 0.6 Nm). The

wire gauge should be 14 to 26 AWG.

Wiring the GLS-PART-CN

The 5-pin terminal block connects the GLS-PART-CN to the Cresnet network (24 Y Z G)

and to a non-system device (EXT).

Wire the GLS-PART-CN

Additional Resources

Visit the product page on the Crestron website (www.crestron.com)

for additional information and the latest rmware updates. Use a QR

reader application on your mobile device to scan the QR image.

Standard 1-gang

electrical box

Ceiling

Mounting

screws (2)

Faceplate

(Not included)

3. Attach the desired decorator style faceplate (not supplied).

GLS-PART-CN Installed in a 1-Gang Electrical Box with Faceplate

4. Turn the Cresnet system power on.

Surface Mount the GLS-PART-CN

After the Cresnet network wiring has been installed and veried, use the following

procedure to surface mount the GLS-PART-CN.

1. Remove the two screws from the back of the GLS-PART-CN and then remove the

bracket. Retain the screws.

Remove these two screws in order to swap the mounting

brackets. Reuse the screws for reassembly using the

other mounting bracket.

Connection to the

control system Contact closure output for

non-system environment

Ceiling Mount in 1-Gang Electrical Box

After the Cresnet network wiring has been installed and veried, use the following

procedure to install the device in a standard 1-gang electrical box.

1. Holding the GLS-PART-CN with the sensors facing the area to be monitored, place

the GLS-PART-CN into the electrical box.

2. Secure the GLS-PART-CN using the included screws.

Installing the GLS-PART-CN in a 1-Gang Electrical Box

Mounting Location

Position the GLS-PART-CN 2 ft (0.6 m) away from the partition. The GLS-PART-CN

sensors must face the partition so that when the partition opens, the sensor sees the

unobstructed room.

Sensor Mounting Location (Bottom View)

2 ft (0.6 m)

Partition

As of the date of manufacture, the device has been tested and found to comply with specications for

CE marking.

Federal Communications Commission (FCC) Compliance Statement

This device complies with part 15 of the FCC Rules. Operation is subject to the following conditions:(1)

This device may not cause harmful interference and (2) this device must accept any interference

received, including interference that may cause undesired operation.

CAUTION: Changes or modications not expressly approved by the manufacturer responsible for

compliance could void the user’s authority to operate the equipment.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital

device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable

protection against harmful interference in a residential installation. This equipment generates, uses and

can radiate radio frequency energy and, if not installed and used in accordance with the instructions,

may cause harmful interference to radio communications. However, there is no guarantee that

interference will not occur in a particular installation. If this equipment does cause harmful interference

to radio or television reception, which can be determined by turning the equipment off and on, the

user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is

connected.

• Consult the dealer or an experienced radio/TV technician for help.

Crestron Electronics, Inc. Installation and Operation Guide - DOC. 7727B

15 Volvo Drive Rockleigh, NJ 07647 (2043368)

Tel: 888.CRESTRON 12.16

Fax: 201.767.7576 Specications subject to

www.crestron.com change without notice.

Industry Canada (IC) Compliance Statement

CAN ICES-3(B)/NMB-3(B)

The product warranty can be found at www.crestron.com/warranty.

The specic patents that cover Crestron products are listed at patents.crestron.com.

Certain Crestron products contain open source software. For specic information, please visit

www.crestron.com/opensource.

Crestron, the Crestron logo, Cresnet, and Crestron Toolbox are either trademarks or registered

trademarks of Crestron Electronics, Inc. in the United States and/or other countries. Other trademarks,

registered trademarks, and trade names may be used in this document to refer to either the entities

claiming the marks and names or their products. Crestron disclaims any proprietary interest in the

marks and names of others. Crestron is not responsible for errors in typography or photography.

This document was written by the Technical Publications department at Crestron.

Congure the GLS-PART-CN

The GLS-PART-CN may not need conguration after installation; conguration is needed

only if the device is not operating as intended. If the partition sensor detects a partition

when there is no partition, or if the partition sensor does not detect a partition when there

is a partition, use the and buttons on the GLS-PART-CN to calibrate the sensors so + –

that the GLS-PART-CN properly detects the partition.

Operation

LED Functionality

The PWR, NET, and ALIGN LEDs perform the following functions:

• Green PWR LED illuminates to indicate that power is applied to the device.

• Yellow NET LED illuminates to indicate trafc on the Cresnet network.

• Red ALIGN LED illuminates to indicate that a partition is detected.

Non-System Mode

When the GLS-PART-CN is operating in a non-system environment, the sensor provides

24 V to the EXT port when a partition is detected. Otherwise, the pin is driven to ground.

2. Install the at bracket to the back of the GLS-PART-CN using the screws removed in

step 1.

3. Holding the GLS-PART-CN with the sensors facing the area to be monitored, secure

the GLS-PART-CN to the ceiling using the screws that are appropriate for the

mounting surface.

Surface Mount the GLS-PART-CN

4. Attach the desired decorator style faceplate (not supplied).

GLS-PART-CN Installed on Surface with Faceplate

Produktspecifikationer

Varumärke:	Crestron
Kategori:	Smarth hem
Modell:	GLS-PART-CN
Enhetsplacering:	Aanrecht
Innehåll (inuti):	23 l
Typ av operation:	Draaiknop
Magnetronkraft:	800 W
Färg på produkten:	Wit
Antal effektnivåer:	6
Dörrgångjärn:	Links
Skivspelare:	Ja
Skivbordsstorlek:	288 mm
Inbyggd display:	Ja
Timer:	Ja
Vikt:	12000 g
Bredd:	489 mm
Djup:	374 mm
Höjd:	275 mm
Nettoskatt:	1250 W
Dörrfärg:	Zwart
Sladdlängd:	0.9 m
Förpackningens vikt:	13500 g
Förpackningens bredd:	552 mm
Djuppackning:	423 mm
Förpackningshöjd:	326 mm
Dörröppningsmekanism:	Uittrekken
Integrerad klocka:	Ja
Typ av klocka:	Elektronisch
Avfrostningsfunktion:	Ja
Skriv timer:	Digitaal
Klockläge:	12/24 uur
Innermått (B x D x H):	330 x 324 x 211 mm
Timerns varaktighet:	99 min
Klockfunktion:	Ja
Invändig beläggning:	Keramisch email
AC-ingångsspänning:	230 V
AC-ingångsfrekvens:	50 Hz
Typ produkt:	Solo-magnetron
Type beeldscherm:	LED