Crosley CR56 Bruksanvisning

Läs nedan 📖 manual på svenska för Crosley CR56 (8 sidor) i kategorin Telefon. Denna guide var användbar för 8 personer och betygsatt med 4.5 stjärnor i genomsnitt av 2 användare

Sida 1/8
910-008800-0420-200 R1
1950’s Classic Pay Phone
Instruction Manual
CR56
www.crosleyradio.com
ENGLISH
FCC Requirements
1. This equipment complies with 47CFRPart 68 and ACTA technical requirements.
On the bottom of this equipment is a label that contains, among other information,
the registration number and ringer equivalence number (REN) for this equipment.
If requested, this information must be provided to the telephone company.
2. The USOC number of the registration jack for the equipment is RJ11C/RJ11W.
3. A FCC compliant telephone cord and modular plug is provided with this equipment.
Thisequipment is designed to be connected to the telephone network or premises
wiring using a compatible modular jack which is TIA/EIA-IS-968 compliant. See
Installation Instructions details.
4. The REN is used to determined the quantity of devices which may be connected
to the telephone line. Excessive RENs on the telephone line may result in the
devices not ringing is response to an incoming call. In most, but not all areas,
the sum of RENs should not exceed five (5.0). To be certain of the number of
devices that may be connected to a line, as determined by the total RENs,
contact the local telephone company.
5. If this terminal equipment causes harm to the telephone network, the telephone
company will notify you in advance that temporary discontinuance of service
may be required. But if advance notice isn’t practical, the telephone company
will notify the customer as soon as possible. Also, you will be advised of your
right to file a compliant with the FCC if you believe it is necessary.
6. The telephone company may make changes in its facilities, equipment, operations
or procedures that could affect the operation of the equipment. If this happens
the telephone company will provide advance notice in order for you to make
necessary modifications to maintain uninterrupted services.
7. The equipment cannot be used on public coin phone service provided by the
telephone company. Connection to party line service is subject to state tariffs.
8. Please follow instructions for repairing if any (e.g. battery replacement section),
otherwise do not alternate or repair any parts of device except specified.
9. This equipment if it uses a telephone handset is hearing aid compatible.
10.If trouble is experienced with this equipment, for repair or warranty information,
please contact service center at the below. If the equipment is causing harm
to the telephone network, the telephone company may request that you disconnect
the equipment until the problem is resolved.
TROUBLESHOOTING
If you experience problems with your telephone, try the following suggestions:
NO DIAL TONE
1. Make sure that all plugs are connected properly. Check the connections at the wall jack, the telephone
body and the handset.
2. Try another modular jack within your home which you know to be working properly.
CALLS CANNOT BE DIALED OR DIALED SLOWLY
Check to make sure that the DIAL MODE switch is in the correct position for the type of service available
in your area.
TELEPHONE DOES NOT RING
Check that RINGER CONTROL switch is not set to OFF.
If there are several telephones connected to the same line, try disconnecting some of the other telephones.
Having too many telephones connected to the same line can cause low ringer volume or poor sound quality
during calls.
CARE AND MAINTENANCE
Avoid rough treatment to your telephone. Do not drop the handset and always replace it gently onto the
cradle.Clean only with a cloth slightly dampened with water only. Do not use detergents, waxes, solvents,
sprays, alcohols or excessive water.
PARTS INCLUDED
Your new telephone includes the following items:
1 - Telephone handset
1 - Handset coil cord
1 - Telephone body
1 - 7 Foot line cord
1 - 15 Inch line cord
2 - Screws with wall archors
4 - Rubber spacer pads.
2 - Tapping screw
1 - Template (See above picture and instructions)
4
TO INSTALL WALL ANCHORS
If the location you have chosen to mount your telephone
is a hollow wall without any beams you will have to use the
included wall anchors.
To install, place the template against the wall where you
wish to place your telephone. Mark the wall at the location
of the two + on the template by pushing a pen or pencil
through the template. Drill a 1/4" hole at each mark.
With a Phillips screwdriver, begin tightening the screw by
turning it clockwise. Stop turning when you feel firm
resistance.
Turn the screw counter clockwise until the screw head is
about 1/4" out of the wall.
Install the 7 foot line cord at back of the telephone . Adjust
the switches to your preference. Position the line cord
through the slot on the bottom of the cabinet. Line up the
holes with the two screws. Place the telephone onto these
two screws and gently pull down.
This may require a little fine tuning until the phone is seated
securely.
ENGLISH
WALL
1/4" HOLE
WALL ANCHOR
PRIOR TO INSTALLION
AFTER INSTALLION

Produktspecifikationer

Varumärke: Crosley
Kategori: Telefon
Modell: CR56

Behöver du hjälp?

Om du behöver hjälp med Crosley CR56 ställ en fråga nedan och andra användare kommer att svara dig




Telefon Crosley Manualer

Telefon Manualer

Nyaste Telefon Manualer