Eco-Flo Plastic Shallow Jet Pump Bruksanvisning

Eco-Flo Pomp Plastic Shallow Jet Pump

Läs nedan 📖 manual på svenska för Eco-Flo Plastic Shallow Jet Pump (33 sidor) i kategorin Pomp. Denna guide var användbar för 4 personer och betygsatt med 4.5 stjärnor i genomsnitt av 2 användare

Ladda ner PDF

Sida 1/33

Owner’s Manual

Plastic Shallow

Jet Pumps

General Safety . . . . . . . . . . . . . . . . . . . . 2

Installation . . . . . . . . . . . . . . . . . . . . . 3-5

Electrical . . . . . . . . . . . . . . . . . . . . . . . . .6

Operation . . . . . . . . . . . . . . . . . . . . . . . . 7

Troubleshooting . . . . . . . . . . . . . . . . . . . 8

Repair Parts . . . . . . . . . . . . . . . . . . . . . . 9

Jet/Tank Assembly . . . . . . . . . . . . . . . . 10

Warranty . . . . . . . . . . . . . . . . . . . . . . . . 11

TABLE OF CONTENTS

Safety: Need safety Info

1. Avoid Pressure Burns/Explosion

2. Avoid Electric Shock

Fill Pump with water: Ensure pump body is lled with water to discharge.

Motor’s Electrical Settings: Set motor to proper voltage,

i.e. voltage supplied to pump – See electrical section

Need Help: Call 1-877-326-3561 for assistance

Important Safety Instructions Safety Labels

Carefully read and follow all safety

instructions in this manual and on pump.

SAVE THESE INSTRUCTIONS – This manual

contains important instructions that should be

followed during installation, operation, and main-

tenance of the product. Save this manual for

future reference.

This is the safety alert symbol. When you

see this symbol on your pump or in this manual,

look for one of the following signal words and be

alert to the potential for personal injury!

Indicates a hazard which, if

not avoided, will result in death or serious injury.

Indicates a hazard which,

if not avoided, could result in death or serious

injury.

Indicates a hazard which, if

not avoided, could result in minor or moderate

injury.

NOTICE indicates practices not related to

personal injury.

Keep safety labels in good condition. Replace

missing or damaged safety labels.

General Safety

Risk of burns. Do not

touch an operating motor. Motors are de-

signed to operate at high temperatures. To

avoid burns when servicing pump, allow it to

cool for 20 minutes after shut-down before

handling.

Do not allow pump or any system compo-

nent to freeze. To do so will void warranty.

Pump water only with this pump.

Periodically inspect pump and system com-

ponents.

Wear safety glasses at all times when work-

ing on pumps.

Risk of explosion. Pump

body may explode if used as a booster

pump.

GENERAL SAFETY

STOP Before you start

For parts or assistance, call ECO-FLO Customer Service at 1-877 326-3561

DEDICATED SHALLOW WELL PUMP INSTALLATIONS

REPLACING AN OLD PUMP

For parts or assistance, call ECO-FLO Customer Service at 1-877 326-3561

Disconnect power to pump before

working on pump or motor.

1. Drain and remove the old pump. Check the old pipe for

scale, lime, rust, etc., and replace it if necessary.

2. Install the pump in the system. Make sure that all pipe

joints in the suction pipe are air-tight as well as water

tight. If the suction pipe can suck air, the pump will not

be able to pull water from the well.

3. Adjust the pump mounting height so that the plumbing

connections do not put a strain on the pump body.

Support the pipe so that the pump body does not take

the weight of piping or ttings.

(Figure 1)

Foot Valve

Stainer

Well Casing

Sanitary Well Seal

To Power Box

Suction Pipe

Priming Tee with

Priming Port, Plug

and Pressure

Gauge

To House

Water

System

Cased Well Installation (Figure 1)

1. Mount the pump as close to the well as possible.

2. Assemble the foot valve, strainer, and well pipe.

Make sure that the foot valve works freely.

3. Lower the pipe into the well until the strainer is ve

feet above the bottom of the well. It should also be at

least 10 feet below the well’s water level.

4. Install a sanitary well seal.

5. Install a priming tee, priming plug, and pressure gauge

to pump’s discharge port. Connect the pipe from the

well to the pump’s suction port, using the fewest

possible ttings-especially elbows – increase friction

in the pipe. The suction pipe should be at least

as large as the suction port on the pump. Support

the pipe so that there are no dips or sags in the pipe,

so not to strain the pump body, and so that it

slopes slightly upward from the well to the pump

(Note: Not doing so can create air locks preventing

the pump from working properly). Seal the suction

pipe joints with PTFE pipe thread sealant tape or a

PTFE-based pipe joint compound. Joints must be air-

and-water-tight. If the suction pipe can suck air,

the pump cannot pull water from well.

6. See instructions on page 8 for connecting discharge

pipe to tank.

Produktspecifikationer

Varumärke:	Eco-Flo
Kategori:	Pomp
Modell:	Plastic Shallow Jet Pump
Färg på produkten:	Zwart
Vikt:	86 g
Förpackningens vikt:	111 g
Förpackningens bredd:	96 mm
Djuppackning:	143 mm
Förpackningshöjd:	32 mm
Snäll:	Ventilator
Ljudnivå (hög hastighet:	28 dB
Material:	Kunststof
Förvaringsfuktighet:	-20 - 70 procent
Spännande:	12 V
Medeltid mellan fel (MTBF):	40000 uur
Anslutning(ar):	1 - Molex Fan (4 pin; PWM)
Rotationshastighet:	2500 RPM
Mått (B x D x H):	80 x 80 x 25 mm
Lämplig plats:	Computer behuizing
Drifttemperatur (TT):	-10 - 70 °C
Relativ luftfuktighet i drift (VV):	0 - 65 procent
Harmoniserad systemkod (HS):	84733080
Ventilator diameter:	80 mm
Nominell nätspänning:	0.16 A
Ventilatorns prestanda:	25.02 cfm