EdgeCraft Chef-s Choice - Commercial 2100 Bruksanvisning
EdgeCraft
Knivslipare
Chef-s Choice - Commercial 2100
Läs nedan 📖 manual på svenska för EdgeCraft Chef-s Choice - Commercial 2100 (19 sidor) i kategorin Knivslipare. Denna guide var användbar för 2 personer och betygsatt med 4.5 stjärnor i genomsnitt av 2 användare
Sida 1/19
INSTRUCTION MANUAL
Commercial
Diamond Hone® Knife Sharpener 2100
Read instructions before use.
It is essential that you follow these
instructions to achieve optimal results.
2
IMPORTANT SAFEGUARDS
When using electrical appliances, basic safety precautions should always be
followed including the following:
1. Read all instructions.
2. To protect against electrical hazards, do not immerse the Chef’sChoice® Model 2100
motor drive section in water or other liquids.
3. Make sure knife blades are cleaned thoroughly before they are inserted in the
Model 2100 sharpener.
4. Disconnect the appliance from its power source when not in use, before cleaning,
during service and when replacing parts (Figure 1).
5. Avoid contacting moving parts.
6. Do not operate any appliance with a damaged cord or plug or after the appliance
malfunctions, or is dropped or damaged in any manner.
U.S. customers: You can return your sharpener to EdgeCraft’s factory for service
where the cost of repair or electrical or mechanical adjustment can be estimated. If the
electrical cord on this appliance is damaged, it must be replaced by the Chef’sChoice®
distributor or other qualified service to avoid the danger of electrical shock.
Outside U.S.: Please return your sharpener to your local distributor where the cost of
repair or electrical or mechanical adjustment can be estimated. If the supply cord of
this appliance is damaged, it must be replaced by a repair facility appointed by
the manufacturer because special tools are required. Please consult your local
Chef’sChoice® distributor.
7. The use of attachments not recommended or sold by EdgeCraft Corporation may cause
fire, electric shock or injury.
8. The Chef’sChoice® Model 2100 Knife Sharpener is designed to sharpen kitchen knives,
pocket knives, and most sports knives. Do not attempt to sharpen ax blades, “parrot
beak” knives or any large knife that does not fit freely in the slots.
9. Do not let the power cord hang over edge of table or counter or touch hot surfaces.
10. When in the “ON” position the Chef’sChoice® should always be on a stable countertop
or table.
11. WARNING: KNIVES PROPERLY SHARPENED ON YOUR CHEF’SCHOICE WILL BE
SHARPER THAN YOU EXPECT. TO AVOID INJURY, USE AND HANDLE THEM WITH
EXTREME CARE. DO NOT CUT TOWARD ANY PART OF YOUR FINGERS, HAND OR
BODY. DO NOT RUN FINGER ALONG EDGE. STORE IN A SAFE MANNER.
12. Do not use outdoors.
13. Appliance is not intended to be used or cleaned by children or persons with reduced
physical, sensory or mental capabilities or lack of experience and knowledge of the
hazards involved. Children shall not play with the appliance.
14. Do not use honing oils, water or any other lubricant with the Chef’sChoice® sharpener.
15. SAVE THESE INSTRUCTIONS.
3
Congratulations on your selection of
the Chef’sChoice® Commercial
Knife Sharpener Model 2100!
You will find the Chef’sChoice® Model 2100 Sharpener puts an exceptionally sharp and
durable edge on all of your knives. It is backed by EdgeCraft, the World Leader in Cutting
Edge Technology®.
The Model 2100 incorporates advanced EdgeCraft diamond abrasive, honing and stropping
technology to produce the sharpest and most durable edges of any sharpener available
today. With it you can quickly and reliably develop a shaving-sharp edge on all your knives.
Once your knives have been sharpened on the Model 2100, resharpening takes less than
1 minute. Consequently if the Model 2100 is conveniently located in your work area, you
can resharpen so rapidly that your knives can be maintained razor sharp every day.
UNPACKING AND PREPARING FOR OPERATION
The Model 2100 has a cast metal motor-drive housing and a detachable Sharpening
Module that are packed together but are not assembled (See Figure 1).
To assemble the Model 2100, insert the Sharpening Module into the guide rails of the
motor-drive housing, (Figure 2) and slide the module toward the motor compartment until
it locks in place. If the sharpening module does not snap together easily and quickly, follow
the instructions in the “Inserting Sharpening Module” section, (Page 12) of this manual.
Figure 1. Model 2100 sharpener disassembled.
On/Off Switch
Release ButtonMotor-drive Section
Detachable Sharpening Module
Produktspecifikationer
| Varumärke: | EdgeCraft |
| Kategori: | Knivslipare |
| Modell: | Chef-s Choice - Commercial 2100 |
Behöver du hjälp?
Om du behöver hjälp med EdgeCraft Chef-s Choice - Commercial 2100 ställ en fråga nedan och andra användare kommer att svara dig
Knivslipare EdgeCraft Manualer
20 September 2024
20 September 2024
19 September 2024
19 September 2024
19 September 2024
19 September 2024
19 September 2024
19 September 2024
19 September 2024
19 September 2024
Knivslipare Manualer
- Knivslipare IKEA
- Knivslipare Adler
- Knivslipare Ambiano
- Knivslipare Ozito
- Knivslipare Gude
- Knivslipare Silvercrest
- Knivslipare OBH Nordica
- Knivslipare Melissa
- Knivslipare Sun Joe
- Knivslipare Beper
- Knivslipare Tacklife
- Knivslipare Eldom
- Knivslipare Einhell
- Knivslipare Guzzanti
- Knivslipare Blokker
- Knivslipare Trebs
- Knivslipare Steba
- Knivslipare Champion
- Knivslipare Bomann
- Knivslipare Graef
- Knivslipare Presto
- Knivslipare Salter
- Knivslipare Bifinett
- Knivslipare Tower
- Knivslipare Gastroback
- Knivslipare Sogo
- Knivslipare Bavaria
- Knivslipare For_Q
- Knivslipare Roadstar
- Knivslipare C3
- Knivslipare Herkules
- Knivslipare Gardenline
- Knivslipare Orava
- Knivslipare Wüsthof
- Knivslipare Berkel
- Knivslipare Petra Electric
- Knivslipare GARDE
- Knivslipare Alpha Tools
- Knivslipare Studio
- Knivslipare Chef's Choice
- Knivslipare IdeenWelt
- Knivslipare Brentwood
- Knivslipare Donau Elektronik
- Knivslipare Sharpal
Nyaste Knivslipare Manualer
7 Januari 2025
7 Januari 2025
7 Januari 2025
30 December 2025
30 December 2025
29 December 2024
9 December 2024
8 December 2024
6 December 2024
11 Oktober 2024