Electro Harmonix Canyon Bruksanvisning

Läs nedan 📖 manual på svenska för Electro Harmonix Canyon (13 sidor) i kategorin Inte kategoriserad. Denna guide var användbar för 11 personer och betygsatt med 4.5 stjärnor i genomsnitt av 2 användare

Sida 1/13
1
CANYON
Multifunction Delay & Looper
Congratulations on your purchase of the Canyon, an tremely powerful yet ex
easy- -use Delay and Looper pedal. to Within the compact Canyon chassis there’s
a vast array of awe-inspiring tones including 10 different types of delays from :
pristine digital to warm tape and more. We’ve even included an exquisite Deluxe
Memory Man emulation plus otherworldly octave delay and shimmer effects. Add
in a full-featured looper, built- or external tap tempo with tap divide, a in
selection of secondary controls and you’re in for a truly grand delay experience.
- GETTING STARTED WITH THE CANYON -
1. Plug the supplied EHX9.6DC AC Adapter into the jack at the top of
the CANYON.
2. Plug your guitar into the INPUT jack and plug the OUTPUT jack into
your amplifier.
3. Turn the 11-position mode knob to the ECHO setting for a standard
digital delay.
4. Set the number of repeats with the FEEDBACK knob, the delay time
with the DELAY knob, and the delay volume with the FX LVL knob.
- TABLE OF CONTENTS -
Getting started with the CANYON 1
Controls 2
Connections 3
Description of modes 4
Using the CANYON’s Loop Mode 5
Tap Tempo with the CANYON 7
Secondary Knob Functionality 9
Secondary Controls Chart 12
Warranty Information and FCC Compliance 13
2
- CONTROLS -
FX LVL Knob Controls the output volume of the delay effect. When
this knob is at the minimum position, the output is only your dry signal.
As the knob is turned up, the delay output increases in volume. As the
knob is turned past 2 o’clock, the dry signal decreases in volume. When
the knob is at the maximum position, the output is only the delay output.
Note: in S/H and LOOP modes, the dry signal remains at unity volume
even as FX LVL is turned to maximum
DELAY Knob Controls the delay time of the CANYON, from a
minimum position of 5 milliseconds to a maximum of 3 seconds.
FEEDBACK Knob Controls the number of repeats of the delayed
signal. As this knob is turned clockwise, the number of repeats increases.
In S/H mode, this knob controls the pluck detection sensitivity. As the
knob is turned clockwise, the sensitivity increases.
In LOOP mode, this knob controls how much of the existing loop is
preserved when overdubbing. As the knob is rotated clockwise, more of
the existing loop is preserved. At the maximum position, the loop will
stay the same volume while overdubbing.
MODE Knob This knob is an 11-position rotary switch that selects
which of the CANYON’s delay modes is active.
TAP/DIVIDE Switch and LED This switch controls the Tap Divide
setting. When the delay time is set using tap tempo, this button controls
the division of the tapped tempo. Press the switch to cycle through the
Tap Divide options, which are indicated by the LED color. Red indicates
quarter notes, orange indicates dotted eighth notes, and green indicates
eighth notes. If the LED does not change color when pressing this
switch, internal Tap Tempo is disabled. Tap Tempo with the See
CANYON on page 7 for the details of tap tempo use.
Footswitch Press this footswitch to switch the pedal between bypass
and effect modes. When the pedal is in effect mode, the LED will be lit.
The footswitch can also be used to set the delay time by tapping it at
least two times. This functionality is enabled from the factory, but can be
disabled. See “Tap Tempo with the CANYONon page 7 for details.
3
TAILS Switch The CANYON allows you to choose whether delayed
echoes continue to repeat or stop immediately after the pedal is
switched to bypass. To control this, remove the CANYON’s bottom cover
and locate the small slide switch on the bottom of the board labeled
“TAILS.”
When Tails are set to ON, the echoes will continue to repeat after the
pedal is switched to bypass, with the number of repeats set by the
FEEDBACK knob. Anything you play after entering bypass will not repeat.
If the pedal is set for infinite feedback (i.e. the FEEDBACK knob is set to
maximum) the repeats will continue until you turn the FEEDBACK knob
down or switch to a different mode.
Note: In Sample/Hold mode, repeats will not continue indefinitely when
Tails are ON. The repeats will fade out over half a second.
When Tails are set to OFF, all repeats will stop as soon as the bypass
switch is pressed, regardless of the FEEDBACK knob setting.
- CONNECTIONS -
INPUT Jack This ¼” jack is the audio input of the CANYON. The
input impedance is 1M .
OUTPUT Jack ON. The output This ¼” jack is the audio output of the CANY
impedance is 680 .
TAP IN Jack Connect an external momentary footswitch to this ¼”
jack to control the delay time by tapping in a tempo. The external switch
should be normally open. Upon engaging the switch, it should create a
short circuit between the Tip and Sleeve of the plug. See “Tap Tempo
with the CANYON” on page 7 for details on using Tap Tempo.
9V Power Jack Plug the output of the CANYON’s supplied EHX9.6DC
200mA AC adapter in the 9V power jack located at the top of the pedal.
The CANYON requires 150mA at 9VDC with a center-negative plug.

Produktspecifikationer

Varumärke: Electro Harmonix
Kategori: Inte kategoriserad
Modell: Canyon

Behöver du hjälp?

Om du behöver hjälp med Electro Harmonix Canyon ställ en fråga nedan och andra användare kommer att svara dig




Inte kategoriserad Electro Harmonix Manualer

Inte kategoriserad Manualer

Nyaste Inte kategoriserad Manualer