Electro Harmonix EHX Tortion Bruksanvisning

Läs nedan 📖 manual på svenska för Electro Harmonix EHX Tortion (4 sidor) i kategorin Inte kategoriserad. Denna guide var användbar för 2 personer och betygsatt med 4.5 stjärnor i genomsnitt av 2 användare

Sida 1/4
1
EHX TORTION
JFET Overdrive/Preamp
Congratulations on your purchase of the EHX TORTION, the most advanced and
dynamic overdrive pedal on the market today. The EHX TORTION uses analog
JFET technology to reproduce the overdrive and distortion character of a tube
amplifier, all in a compact, durable die-cast chassis. Three-band EQ and a Pre-
Gain switch hone your sound, and a footswitchable BOOST mode adds a second
channel of modern high-gain tones.
WARNING: Your EHX TORTION comes equipped with an Electro-Harmonix 9.6DC-200BI
power supply (same as used by Boss® & Ibanez®
: 9.6 Volts DC 200mA). The EHX
TORTION requires 27mA at 9VDC with a center negative plug. Using the wrong adapter
may damage your unit and void the warranty. The EHX TORTION also accepts 9V
batteries, we recommend alkaline.
- MODES OF OPERATION: NORMAL VS. BOOST -
The EHX TORTION operates in two modes: NORMAL and BOOST. The NORMAL
mode uses three JFET stages for low to medium gain sounds. The volume and
gain controls for NORMAL mode are located in the top row of knobs. The boost
mode is activated with the BOOST footswitch, and adds a fourth gain stage for
modern high-gain tones. The BOOST volume and gain knobs are on the bottom
row of the controls. The volume and gain controls for each mode are completely
independent, allowing the two modes to function like two separate channels on a
tube amplifier.
- CONTROLS -
GAIN Knob The NORMAL GAIN knob is on the top row. This knob controls the
amount of input gain when the pedal is in NORMAL mode. This knob is disabled
when in BOOST mode.
PRE-GAIN Switch This switch controls the level and tone of the initial input
signal to the EHX TORTION. This switch has four settings. The two leftmost
settings select a lower input level, for vintage plexi tones. The two rightmost
settings are higher gain for a modern, hot-rodded sound. Each pre-gain setting
has two tone selections: Full or Tight, indicated by and . The Full setting has F T
2
more bass for a bigger sound. The Tight setting focuses the bass frequencies for
a more modern tone.
BASS Knob Controls the level of the bass frequency range.
MID Knob Controls the level of the middle frequency range.
TREBLE Knob Controls the level of the treble frequency range.
VOL Knob The NORMAL VOL knob is on the top row. This knob controls the
output level of the EHX TORTION when in NORMAL mode. This knob is disabled
when in BOOST mode.
BOOST GAIN Knob The BOOST GAIN knob is on the bottom row. This knob
controls the amount of input gain when the pedal is in BOOST mode. This knob
is completely independent from the NORMAL GAIN knob, and is disabled when in
Normal mode.
BOOST VOL Knob The BOOST VOL knob is on the bottom row. This knob
controls the output level of the EHX TORTION when in BOOST mode. This knob
is completely independent from the NORMAL VOL knob, and is disabled when in
Normal mode.
BYPASS Footswitch LED and red footswitch selects whether the EHX This
TORTION is engaged or in buffered bypass mode. When the effect is engaged,
the red LED will be lit.
BOOST Footswitch and blue LED This footswitch toggles Boost mode on
and off. When in Boost mode, the blue LED will be lit.
INPUT Jack EHX TORTION. The input This ¼” jack is the audio input for the
impedance is . 1M
OUTPUT Jack ck is the audio output from the EHX TORTION. The This ¼” ja
output impedance depends on the VOLUME setting, ranging from k . 250to 25
BOOST SW Jack Allows an external momentary footswitch to control toggling
Boost mode on and off. The external switch should be normally open. Upon
engaging the switch, it should create a short circuit between the Tip and Sleeve
of the plug inserted into the BOOST SW jack on the EHX TORTION. Releasing
the switch should open the circuit between the Tip and Sleeve. The BOOST SW
jack is connected in parallel with the BOOST Footswitch so they can both work at
the same time. A suggested momentary footswitch that has been tested with the
EHX TORTION is the Boss FS-5U Momentary Foot Switch.
DI OUTPUT Jack This is a low impedance output capable of driving 600 to
plug directly into a mixing console or recording equipment. The DI output uses
an all-analog amp/cabinet simulator to create the sound of a real 4x12 cabinet.
3
This output’s signal is line-level, and is controlled by the active Volume knob.
When the EHX TORTION is in bypass mode, the DI output and cabinet simulator
are still active, and send your bypass signal through the simulator. This can be
used to warm up the sound of other pedals or processors for recording.
9V Power Jack Although the EHX TORTION accepts 9V Batteries, it is
supplied from the factory with an Electro-Harmonix 9.6DC-200BI power supply.
Plug the output of the supplied AC Adapter into the 9V power jack located at the
top of the EHX TORTION. The EHX TORTION draws 27mA at 9VDC with a center
negative plug. The EHX TORTION accepts Boss® and Ibanez® style AC Adapters.
- CHANGING THE BATTERY -
To change the 9-volt battery, you must remove the 4 screws on the bottom of
the EHX TORTION. Once the screws are removed, you can take off the bottom
plate and change the battery. Please do not touch the circuit board while the
bottom plate is off or you risk damaging a component. Avoid touching the
trimmers on the circuit board. These have been set at the factory for proper
operation. Changing these trimmers can result in a non-functional unit.
- WARRANTY INFORMATION -
Please register online at http://www.ehx.com/product-registration or complete
and return the enclosed warranty card within 10 days of purchase. Electro-
Harmonix will repair or replace, at its discretion, a product that fails to operate
due to defects in materials or workmanship for a period of one year from date of
purchase. This applies only to original purchasers who have bought their product
from an authorized Electro-Harmonix retailer. Repaired or replaced units will then
be warranted for the unexpired portion of the original warranty term.
If you should need to return your unit for service within the warranty period,
please contact the appropriate office listed below. Customers outside the regions
listed below, please contact EHX Customer Service for information on warranty
repairs at info@ehx.com or +1- - -8300. USA and Canadian customers: 718 937
please obtain a (RA#) from EHX Customer Return Authorization Number
Service before returning your product. Include with your returned unit: a written
description of the problem as well as your name, address, telephone number, e-
mail address, and RA#; and a copy of your receipt clearly showing the purchase
date.
United States & Canada
EHX CUSTOMER SERVICE
ELECTRO-HARMONIX
c/o NEW SENSOR CORP.
47-50 33RD STREET
LONG ISLAND CITY, NY 11101
Tel: 718- - 937 8300

Produktspecifikationer

Varumärke: Electro Harmonix
Kategori: Inte kategoriserad
Modell: EHX Tortion

Behöver du hjälp?

Om du behöver hjälp med Electro Harmonix EHX Tortion ställ en fråga nedan och andra användare kommer att svara dig




Inte kategoriserad Electro Harmonix Manualer

Inte kategoriserad Manualer

Nyaste Inte kategoriserad Manualer