Electro-Voice XLE191-FG Bruksanvisning

Electro-Voice högtalare XLE191-FG

Läs nedan 📖 manual på svenska för Electro-Voice XLE191-FG (4 sidor) i kategorin högtalare. Denna guide var användbar för 2 personer och betygsatt med 4.5 stjärnor i genomsnitt av 2 användare

Ladda ner PDF

Sida 1/4

X-Line Very Compact

Crossover Retrofit

Installation Instructions

YOU WILL NEED:

- ONE SHORT-HANDLED PHILLIPS SCREWDRIVER

- ONE SHORT-HANDLED ¼” NUT DRIVER

- SMALL SCRAPER OR PUTTY KNIFE

- SMALL WIRE (SIDE) CUTTER TO SNIP CABLE TIES

- CARPENTERS’ WOOD GLUE

- 3M SUPER 77 SPRAY ADHESIVE OR LIQUID

CONTACT CEMENT

1) REMOVE THE 6 SCREWS HOLDING THE INPUT PANEL. CAREFULLY UNPLUG THE MOLEX CONNECTOR

FOR THE TRANSDUCER WIRING AND PEEL OFF THE CONTACT INFORMATION LABEL COVERING THE

“BIAMP” INDICATOR WINDOW ON XLD OR “PASSIVE” INDICATOR WINDOW ON XLE.

2) REMOVE THE GRILLE.

3) REMOVE THE WOOFER THAT SHARES THE SAME CHAMBER AS THE INPUT PANEL.

4) STAND THE ENCLOSURE ON ONE END WITH THE NOW OPEN CHAMBER ON TOP. REMOVE THE BATTING

FROM THIS CHAMBER AND DISCARD.

5) USING THE ¼” NUT DRIVER, UNSCREW THE TWO CABLE TIES SECURING THE WIRES TO THE DIVIDER

PANEL. SAVE THE SCREWS.

6) CAREFULLY SNIP THROUGH THE CABLE TIES TO FREE THE WIRES FROM THEIR BUNDLE, TAKING CARE

NOT TO DAMAGE THE INSULATION ON THE WIRES.

7) SCRAPE OFF ANY EXCESS GLUE DRIBBLES, ADHESIVE AND LEFTOVER BATTING FROM THE SIDEWALLS

OF THIS CHAMBER, ESPECIALLY THE DIVIDER PANEL. TAKE CARE NOT TO ALLOW WIRING TO BE

DAMAGED BY YOUR SCRAPER BLADE. DO NOT DISTURB CAULKING MATERIAL IN WIRING THRU-HOLE

TO HF CHAMBER. IF YOU DO, IT MUST BE RE-SEALED WITH SILICONE RTV CAULK.

8) NOTE THE CHANNELS MILLED INTO ONE SIDE OF THE NEW MOUNTING BOARD. (THE SIDE WITH THE T-

NUTS SHOWING) APPLY AN EVEN LAYER OF WOOD GLUE TO THE FLAT AREAS ADJACENT TO THESE

CHANNELS. (SEE FIGURE 1)

Glue

Rounded Corner

Glue

Rounded Corner

Glue

000-649103 TSILSTRAPTIFORTERREVOSSORCE/DLX

N/P NOITPIRCSED .YTQ

000-080207 DRAOBGTMTIFORTERREVOXE/DLX 1

000-804065 E/DLX,REVOX 1

90883 NOLYN,TALF,REHSAW 7

PCL412706 8/7X42-01,WERCS 7

31437 EITELBAC 1

000-126195 GNITTAB FL1

000-141185 WERCSLLAWYRD”¼1x8# 6

47401183 TIFORTERREVOXE/DLX,SNOITCURTSNI 1

This End of Mounting Board

to Rear of Enclosure

T-Nuts

Figure 1: Apply Glue to Mounting Board

Channel

9) CENTER THE NEW CROSSOVER MOUNTING BOARD TOP-TO-BOTTOM ON THE DIVIDER PANEL WITH THE

WIRING TO THE HF CHAMBER ROUTED THROUGH THE ANGLED CHANNEL ON THE UNDER-SIDE OF THE

BOARD. THE END OF THE BOARD WITH THE ROUNDED CORNERS MUST BE FLUSH AGAINST THE REAR

OF THE ENCLOSURE AND THE SCREW POINT STICKING THROUGH FROM THE HF CHAMBER SHOULD BE

IN THE NARROWER CHANNEL NEAR THE FRONT. MOUNTING BOARD MUST LAY FLAT AGAINST THE

DIVIDER PANEL. (SEE FIGURE 2)

Figure 2: Attach Mounting Board to Divider Panel on Interior of Enclosure

10) INSERT ONE DRYWALL SCREW (PROVIDED) INTO EACH OF THE SIX RECESSED HOLE LOCATIONS AND

TIGHTEN SECURELY.

11) USING ONE OF THE ORIGINAL SCREWS AND THE NEW CABLE TIE, SECURE THE WOOFER WIRES TO

THE DIVIDER PANEL NEAR THE FRONT OF THE ENCLOSURE. (SEE FIG. 2 FOR LOCATION) REMEMBER

TO LEAVE PLENTY OF SLACK AT EACH END TO REACH BOTH THE WOOFER TERMINALS AND THE INPUT

PANEL. SNIP OFF THE EXCESS CABLE TIE AND DISCARD.

Rounded Corner Rounded Corner

Transducer

Wiring Harness

1/4” Hex Screw

and Wire Tie

Woofer Wires

Drywall Screws

in Recessed

Holes

(6 places)

Mounting Board to be

Centered on Divider

Panel

Bottom Side Top Side

Divider Panel Between

LF Chamber and HF

Chamber

12) APPLY SUPER 77 (OR CONTACT CEMENT) TO THE ENTIRE BOTTOM PANEL AND THE END PANEL. WAIT

ABOUT 1 MINUTE, (DO NOT ALLOW ADHESIVE TO DRY COMPLETELY) THEN FOLD THE NEW PIECE OF

BATTING IN HALF AND INSERT IT THROUGH THE WOOFER OPENING. PLACE THE FRONT EDGE OF THE

BATTING UP AGAINST THE BAFFLE AND TUCK THE ADJACENT EDGE DOWN BETWEEN THE BOTTOM

PANEL AND THE NEW MOUNTING BOARD. PRESS THE BATTING UP INTO THE CORNER WITH THE SIDE

PANEL AND FOLD IT AROUND AS FAR AS IT WILL GO. BATTING SHOULD NOT BLOCK ANY PART OF THE

PORT OPENING. ALLOW EXCESS TO FOLD OVER ONTO REAR PANEL BUT DO NOT GLUE TO REAR

PANEL. (SEE FIGURE 3)

13) PLACE A PLASTIC WASHER ON EACH OF THE SEVEN 10-24 MACHINE SCREWS AND INSERT ONE INTO

EACH OF THE SEVEN GROMMETS ON THE COMPONENT SIDE OF THE CROSSOVER. NOTE THAT THE

GROMMETS ARE FURTHER IN FROM THE END OF THE CIRCUIT BOARD ON ONE END. INSERT THE

CROSSOVER THROUGH THE WOOFER OPENING THIS END FIRST AND POSITION SO ALL SEVEN SCREWS

LINE UP WITH THEIR CORRESPONDING THREADED HOLES IN THE MOUNTING BOARD BEFORE

SECURELY TIGHTENING ALL SEVEN SCREWS. DO NOT TRAP ANY WIRES UNDER CIRCUIT BOARD.

14) ON THE INPUT PANEL, SELECT THE OPERATING MODE BY MOVING THE 4-WIRE JUMPER PLUG AT THE

EDGE OF THE CIRCUIT BOARD.

XLD: SELECT “BIAMP” OR “TRIAMP” OPERATION

XLE: SELECT “PASSIVE” OR “BIAMP” OPERATION

MAKE SURE ALL 4 PINS ARE COMPLETELY ENGAGED.

15) RE-CONNECT THE TRANSDUCER WIRING MOLEX CONNECTOR TO THE HEADER ON THE BACK OF THE

INPUT PANEL CIRCUIT BOARD NEAR THE TOP EDGE. CONNECT THE 4-WIRE MOLEX PLUG FROM THE

CROSSOVER TO THE 4-PIN HEADER LOCATED NEAR THE CENTER OF THE BOARD. DOUBLE CHECK

YOUR WORK. BE SURE ALL PINS ARE COMPLETELY AND SECURELY ENGAGED.

16) RE-INSTALL THE INPUT PANEL.

Figure 3: Installing New Batting in Low-Frequency Chamber

Fold Excess Batting over

onto Rear Panel but Do

Not Glue to Rear Panel

Batting must not

Obstruct Port Opening

Note: This View

Shows the

Enclosure without

the Baffle

or Components

Start Batting in this

Corner

Transducer Wiring

Harness

Produktspecifikationer

Varumärke:	Electro-Voice
Kategori:	högtalare
Modell:	XLE191-FG

Behöver du hjälp?

Om du behöver hjälp med Electro-Voice XLE191-FG ställ en fråga nedan och andra användare kommer att svara dig

Ditt namn*

Din e-post*

Skriv din fråga här

högtalare Electro-Voice Manualer

Electro-Voice XLE191-FG Bruksanvisning

9 Januari 2025

Electro-Voice Sx600 Bruksanvisning

9 Januari 2025

Electro-Voice Tour X TX1122FM Bruksanvisning

2 Oktober 2024

Electro-Voice EVID C10.1 Bruksanvisning

2 Oktober 2024

Electro-Voice EKX-15 Bruksanvisning

30 September 2024

Electro-Voice Sx100+ Bruksanvisning

24 September 2024

Electro-Voice Zx1 Bruksanvisning

24 September 2024

Electro-Voice Tour X TX2152 Bruksanvisning

21 September 2024

Electro-Voice EVID-40C Bruksanvisning

19 September 2024

Electro-Voice EVOLVE30M-EU Bruksanvisning

17 September 2024

högtalare Manualer

Nyaste högtalare Manualer

Heco CELAN GT 502 Bruksanvisning

9 Januari 2025

Heco INC 602 Bruksanvisning

9 Januari 2025

Yorkville Paraline PSA1 Bruksanvisning

9 Januari 2025

Boston Acoustics VS 336 Bruksanvisning

9 Januari 2025

Klipsch ProMedia 2.1 Wireless Bruksanvisning

8 Januari 2025

Polk F/X 1000 Bruksanvisning

8 Januari 2025

QSC Wideline 10 WL2102-w Bruksanvisning

8 Januari 2025

RCF HDL 36-AS Bruksanvisning

8 Januari 2025

Anchor Audio MEGA-DP DUAL/EM/CM Bruksanvisning

8 Januari 2025

IDance Cuty Cat Bruksanvisning

8 Januari 2025