Epson WorkForce 1100 Bruksanvisning

Epson Skrivare WorkForce 1100

Läs nedan 📖 manual på svenska för Epson WorkForce 1100 (8 sidor) i kategorin Skrivare. Denna guide var användbar för 9 personer och betygsatt med 4.5 stjärnor i genomsnitt av 2 användare

Sida 1/8
WorkForce 1100 Series
Notices and Warranty
®
2
Important Safety Instructions
Before using your WorkForce 1100 Series, read and follow these safety instructions:
Be sure to follow all warnings and instructions marked on the printer.
Use only the type of power source indicated on the printer.
Place the printer near a wall outlet where the plug can be easily unplugged.
Avoid plugging the printer into an outlet on the same circuit as a photo copier or air
control system that regularly switches on and off, or on an outlet controlled by a wall
switch or timer.
Do not let the power cord become damaged or frayed.
If you use an extension cord with the printer, make sure the total ampere rating of the
devices plugged into the extension cord does not exceed the cord’s ampere rating.
Also, make sure the total ampere rating of all devices plugged into the wall outlet does
not exceed the wall outlet’s ampere rating.
Always turn off the printer using the power button, and wait until the power
light stops flashing before unplugging it or cutting off power to the electrical outlet.
Place the printer on a flat, stable surface that extends beyond its base in all directions.
It will not operate properly if it is tilted or at an angle.
Leave enough room around the printer for sufficient ventilation. Do not block or
cover openings in the case or insert objects through the slots.
Make sure the back of the printer is at least 4 inches (10 cm) away from the wall, and
leave enough space in front of the printer for the paper to be fully ejected.
Avoid locations that are subject to rapid changes in heat or humidity, shocks or
vibrations, or dust.
Do not place the printer near a radiator or heating vent or in direct sunlight.
Keep the printer away from potential sources of electromagnetic interference, such as
loudspeakers or the base units of cordless telephones.
When connecting the printer to a computer or other device with a cable, ensure the
correct orientation of the connectors. Each connector has only one correct
orientation. Inserting a connector in the wrong orientation may damage both devices
connected by the cable.
Do not touch the flat white cable inside the printer.
Do not move the print head by hand; this may damage the printer.
Do not spill liquid on the printer.
Do not use aerosol products that contain flammable gases inside or around the
printer. Doing so may cause fire.
3
Except as specifically explained in your documentation, do not attempt to service the
printer yourself.
Unplug the printer and refer servicing to qualified service personnel under the
following conditions: if the power cord or plug is damaged; if liquid has entered the
product; if the product has been dropped or the case damaged; if the product does not
operate normally or exhibits a distinct change in performance. Adjust only those
controls that are covered by the operating instructions.
If damage occurs to the plug, replace the cord set or consult a qualified electrician. If
there are fuses in the plug, make sure you replace them with fuses of the correct size
and rating.
Before transporting the printer, make sure that the print head is in the home (far
right) position and the ink cartridges are in place.
When storing or transporting the printer, do not tilt it, stand it on its side, or turn it
upside down; otherwise ink may leak from the cartridges.
Ink Cartridge Safety
Keep ink cartridges out of the reach of children and do not drink the ink.
Be careful when you handle used ink cartridges; there may be ink remaining around
the ink supply port. If ink gets on your skin, wash it off with soap and water. If it gets
in your eyes, flush them immediately with water.
Do not put your hand inside the printer or touch any cartridges during printing.
Install a new ink cartridge immediately after removing an expended one. Leaving
cartridges uninstalled can dry out the print head and may prevent the printer from
printing.
If you remove an ink cartridge for later use, protect the ink supply area from dirt and
dust and store it in the same environment as the printer. Note that there is a valve in
the ink supply port, making covers or plugs unnecessary, but care is needed to prevent
the ink from staining items that the cartridge touches. Do not touch the ink cartridge
ink supply port or surrounding area.
Use an ink cartridge before the date printed on its package.
Do not dismantle an ink cartridge. This could damage the print head.
Store ink cartridges in a cool, dark place.
After bringing an ink cartridge inside from a cold storage site, allow it to warm up at
room temperature for at least three hours before using it.
Store ink cartridges with their labels facing upward. Do not store cartridges upside
down.

Produktspecifikationer

Varumärke: Epson
Kategori: Skrivare
Modell: WorkForce 1100

Behöver du hjälp?

Om du behöver hjälp med Epson WorkForce 1100 ställ en fråga nedan och andra användare kommer att svara dig




Skrivare Epson Manualer

Skrivare Manualer

Nyaste Skrivare Manualer