Fisher 29841 Bruksanvisning

Fisher Inte kategoriserad 29841

Läs nedan 📖 manual på svenska för Fisher 29841 (2 sidor) i kategorin Inte kategoriserad. Denna guide var användbar för 2 personer och betygsatt med 4.5 stjärnor i genomsnitt av 2 användare

Ladda ner PDF

Sida 1/2

1. Do not use reel at higher pressures or temperatures than listed on

the back of these instructions.

2. Remove all spring tension before beginning dissassembly process.

SAFETY

INSTALLATION:

LUBRICATION:

REPLACING HOSE:

ADJUSTMENTS:

REPAIRS:

MOUNTING:

Dimensions

A 11 3/16”

B 11 1/16”

C 6”

D 8”

E 4 3/16”

F 6”

G 2 1/2”

Operating Instructions

Model: 29841 / 29662

Spring Driven Reel

Fisher Manufacturing Co. • 1900 “O” Street, Tulare, CA 93274

Ph: 800-421-6162 / 559-685-5200 • Fax: 800-832-8238 / 599-685-5222

Part No.75031 Rev.A

A flexible hose connection must be used between the hose reel inlet and the source of supply to prevent possible

misalignment and binding. Turn over the page for more detailed instructions and drawing configuration.

This reel is configured to be under the counter mounted.The hose reel is equipped with a universal mounting bracket so that it can

be mounted on the floor, wall or hose guide arm accessory kit (sold separately)or ceiling. In order to modify it”s factory set position the

can be moved to the position desired by removing two screws fastening the spring case to the reel base. Shift the guide arm bracket

so the hose comes off the reel at the desired position and replace the screws. CAUTION: Unless reel was specified differently when

ordering. maximum height is 16 feet.

Hose reel spring and bearings are factory lubricated and require no further lubrication.

1. Wind spool flange clockwise-facing swivel-until spring is tight

2. Back off three turns and latch.

3. Insert hose through roller guide.

4. Connect hose fitting to swivel joint and secure hose with clamps.

To adjust spring tension, add or remove wraps of hose from the spool, one wrap at a time until desired tension is

obtained.

Extensive repairs should be performed only by an authorized serviceman or factory to avoid damage which may

void your warranty. Remove all spring tension before beginning disassembly process.

Model: 29841 / 29662

Model: 74989 Reel Kit Utilty Spray Valve / Pro Spray

Page 2

Description

29841 or 29662

Hose I.D. and Length 3/8” x 20’

Reel Inlet Connection 3/8” NPT (F)

Hose Outlet Connection 1/4” NPT(M)

Max. Operating Pressure 300 PSI

Max. Operating Temperature 160 °F

Item # Description # Req.

1 Swivel and elbow assy, 3/8 LP, 3/8 MPT x FPT 1

2 Hardware Kit 1

Spacing washer 1.005 ID x 1.312 OD x .020 THK 2

Snap ring 1

Hex washer screw 3

Hex lock nut M5 8

Machine screw M5 x 10 8

Screw set 3/8-16 x 1/2 1

Nyloc nut M6 2

U-bolt 1

3 Main shaft with snap ring 1

4 Sheave Assembly 1

Sheave flange 1

Sheave disc 1

Ratchet arbor 1

Item # Description # Req.

5 Base and roller assembly 1

Tube rivet 4

Universal roller (2”) 1

Base weldment assembly 1

6 Drive spring assembly 1

7 Spring case stud 1

8 Spring case assembly 1

9 Bumper assembly

10 Latch pawl assembly 1

Latch pin 1

Latch pawl 1

Torsion spring 1

11 Hose assemby

12 Guide arm assembly w/ hardware

(sold separately) 1

Item # Req.# Part Description

13 175066 Hose RR 3/8m x 1/2f x 1 1/2 ft

14 12900-3309 Bushing 1/4f x 3/8m brs

12980-R020 Tube vinyl clear 6 inch15

16 12913-3/8 Handle 3/4-14f X 3/8f

17 12922-5000 Gasket Handle

18 12920 or 2990 Utility Spray Valve or Pro Spray

19 13298 PST Thread Sealant

1. Connect the lead-in line (13) to the reel (29841 / 29662) inlet located on the right-hand side of the hose reel,

by appling PST (19) or plumbers tape on the male 3/8” NPT threads on the lead-in line (13) and thead it

to the reel (29841) using a wrench to support the swivel while tightening the lead-in line.

2. Connect the 1/2” female end of the lead-in line (13) to the water supply using PST (19) or plumbers tape

and tighent.

3. Turn on water supply and flush the reel line to remove any debis from the reel for a few seconds and

then turn off water supply.

4. Attach the bushing (14) to the reel hose (11) By appling PST (19) or plumbers tape on the 1/4” NPT male threads on reel hose

and tighten.

5. Slide the clear vinyl tube (15) over the reel hose up to the bumper (9).

6. Attach the handle (16) to the reel hose (11). By appling PST (19) or plumbers tape on the 3/8” NPT male threads on reel hose

and tighen.

7. Insert the gasket handle (17) into the handle (16) and then connect the pro spray valve (18).

8. Turn water supply on and check for leaks.

NOTE: Apply PST or Plumber Tape on

the following locations to prevent any

leaks.

Produktspecifikationer

Varumärke:	Fisher
Kategori:	Inte kategoriserad
Modell:	29841
Färg på produkten:	Grey, White
Bredd:	1828.8 mm
Djup:	762 mm
Höjd:	812.8 mm

Behöver du hjälp?

Om du behöver hjälp med Fisher 29841 ställ en fråga nedan och andra användare kommer att svara dig

Ditt namn*

Din e-post*

Skriv din fråga här

Inte kategoriserad Fisher Manualer

Fisher 29841 Bruksanvisning

7 September 2024

Inte kategoriserad Manualer

Nyaste Inte kategoriserad Manualer

Livarno Lux IAN 93986 Bruksanvisning

18 December 2024

Livarno Lux IAN 111166 Bruksanvisning

18 December 2024

Livarno Lux Z30347A Bruksanvisning

18 December 2024

Livarno Lux IAN 338294 Bruksanvisning

18 December 2024

Livarno Lux IAN 63843 Bruksanvisning

18 December 2024

Livarno Lux IAN 110725 Bruksanvisning

18 December 2024

Livarno Lux IAN 353907 Bruksanvisning

18 December 2024

Livarno Lux IAN 321327 Bruksanvisning

18 December 2024

Livarno Lux IAN 353560 Bruksanvisning

18 December 2024

Livarno Lux IAN 345071 Bruksanvisning

18 December 2024